91.060.20 屋顶 标准查询与下载

ASTM D6917-16(2022) 预制垂直排水管（PVD）试验方法选择的标准指南

1.1 This guide provides recommendations for the selection of appropriate test methods for prefabricated vertical geocomposite drains (sometimes referred to as wick drains) used in geotechnical engineering applications to provide consistency in data reporting. 1.2 This guide includes test methods for all types of prefabricated geocomposite drains manufactured in a plant and consisting of a polymeric core structure with a synthetic fabric (geotextile) jacket for filtration. 1.3 This guide is intended to aid all personnel involved in the selection, manufacture, installation, or evaluation of prefabricated vertical drains. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Selection of Test Methods for Prefabricated Vertical Drains (PVD)

ASTM D7954/D7954M-22 用无损电阻抗扫描仪测量屋顶和防水系统的湿度的标准实施规程

Standard Practice for Moisture Surveying of Roofing and Waterproofing Systems Using Nondestructive Electrical Impedance Scanners

YS/T 5410-2022 屋面工程施工操作规程

Operational specification for construction of roof

DB11/T 1832.9-2022 建筑工程施工工艺规程 第9部分：屋面工程

Construction technology specification for building engineering Part 9: Roofing engineering

T/SDGSY 5-2022 陶瓷太阳板锚桩结构坡屋面热水系统应用技术规程

1.0.1为规范陶瓷太阳板锚桩结构坡屋面热水系统的安装，推动陶瓷太阳板锚桩结构坡屋面热水系统的应用制定本规程。 1.0.2本规程适用于新建、扩建和改建民用与工、农业建筑以及既有建筑改造中,安装陶瓷太阳板的工程项目。 1.0.3陶瓷太阳板锚桩结构坡屋面热水系统的设计、施工及验收，除应符合本规程的规定外，尚应符合国家现行有关标准的规定。       本规程主要内容包括：1、总则，2、术语，3、基本规定，4、结构，5、材料，6、施工，7、检测与验收等七部分。

Technical specification for ceramic solar panel anchor pile structure insloping roof hot water system

JIS A 6021:2022 用于建筑物防水卷材涂层的液涂化合物

Liquid-applied compounds for waterproofing membrane coating of buildings

ASTM C1570-22 混凝土和粘土屋顶砖抗风性的标准试验方法（透气性法）

1.1 The air permeability of tile roofing systems is a critical factor in determining the wind resistance of tile roofing as applied to a roof. This Standard describes a procedure for measuring the air permeability of clay and concrete tile and slate roof systems when applied to a small section of roof deck in accordance with the manufacturer’s instructions. 1.2 This test procedure measures the air permeability of a laid array of unsealed clay or concrete roof tiles or slates. The tiles or slates shall have a thickness between 1⁄8-in. (3-mm) and 2-in. (51-mm). 1.3 The text of this test method references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Wind Resistance of Concrete and Clay Roof Tiles (Air Permeability Method)

ASTM C1492-22 混凝土屋顶瓦标准规范

1.1 This specification covers concrete tiles intended for the use as roof covering where durability and appearance are required to provide a weather-resistant surface of specified design. 1.2 Tiles are manufactured from portland cement, water, and mineral aggregates with or without the inclusion of other materials. 1.3 Tiles are shaped during manufacturing by molding, pressing, or extrusion. The shaping method can be used to describe the tile. 1.4 Other constituents, such as chemical and mineral admixtures established as suitable for use in concrete, shall conform to ASTM standard specifications where applicable, or shall be shown by tests or experience not to be detrimental to the durability of concrete. 1.5 Tiles are generally planar or undulating rectangular shapes available in a variety of cross-sectional areas profiles, shapes, sizes, surface textures, and colors. NOTE 1—Concrete roof tiles covered by this specification are made from lightweight or normal weight aggregates, or both. NOTE 2—When particular features are desired, such as color, surface texture for appearance, or other special features, such properties should be specified by the purchaser. However. the local sellers should be consulted as to the availability of concrete roof tile having a desired feature. 1.6 The text of this specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Concrete Roof Tile

ASTM C1569-22 混凝土和粘土屋顶砖抗风性的标准试验方法（风洞法）

1.1 This test method covers a procedure to determine the resistance of concrete and clay roof tiles to simulated wind effects in a wind-tunnel apparatus. Simulated wind velocities of 70 mph (31 m/s) to 130 mph (58 m/s) are employed. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Wind Resistance of Concrete and Clay Roof Tiles (Wind Tunnel Method)

ASTM F2021-17(2022) 塑料虹吸屋顶排水系统的设计和安装标准指南

1.1 This guide covers design and installation considerations for plastic siphonic roof drain systems for industrial, commercial, public, and residential buildings. Requirements for materials, pipe, and fittings are included. 1.2 The interchangeability of pipe and fittings made by different manufacturers is not addressed in this guide. Transition fittings for joining pipe and fittings of different manufacturers is provided for in the referenced pipe and fitting specification. 1.3 In referee decisions, the SI units shall be used for metric-sized pipe and inch-pound units for pipe sized in the IPS system (ANSI B36.10). In all cases, the values given in parentheses are for information only. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems

ASTM D8257/D8257M-22 陡坡屋顶用机械连接聚合屋顶垫层的标准规范

1.1 This specification addresses mechanically attached polymeric roof underlayment used in steep slope roofing. 1.2 The objective of this specification is to provide a finished product that will be used as a water-shedding underlayment layer on steep sloped roofs prior to and after installation of the primary roof covering. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Mechanically Attached Polymeric Roof Underlayment Used in Steep Slope Roofing

DIN EN 508-1:2022 金属板屋顶和覆层产品 钢、铝或不锈钢板自支撑产品规范 第1部分：钢；德文版 EN 508-1:2021

This part of EN 508 specifies requirements for self-supporting roofing, covering, wall cladding, lining, liner trays and tiles products for discontinuous laying made from metallic coated steel sheet with or without additional organic coatings. Sheets intended to be used with insu

Roofing and cladding products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet - Part 1: Steel; German version EN 508-1:2021

DB11/T 851-2021 聚脲防水涂料应用技术规程

Polyurea Waterproof Coating Application Technical Regulations

DB11/T 1945-2021 屋面防水技术标准

Technical standard for roof waterproofing

CJ/T 245-2021 建筑屋面排水用雨水斗通用技术条件

General technical specifications for rainwater buckets for building roof drainage

T/CECS 959-2021 焊接不锈钢屋面工程技术标准

主要技术内容包括：总则、术语、基本规定、材料、设计、施工、验收、维护等。

Technical Standards for Welded Stainless Steel Roofing Engineering

ASTM D6383/D6383M-99(2021) 三元乙丙橡胶屋顶薄膜材料制成的粘合接头的失效时间（蠕变断裂）的标准实施规程

1.1 This practice covers sample preparation temperatures, test parameters, and specimen exposure conditions that are applicable when Test Method D5405/D5405M is used for conducting time-to-failure (creep-rupture) tests of adhesive joints fabricated from ethylene-propylene-diene terpolymer (EPDM) roof membrane material. 1.2 This practice is applicable to joints fabricated in the laboratory from EPDM roof membrane materials and adhesives received from suppliers, and to joints prepared from EPDM seams sampled from field installations. 1.3 The joints are bonded using preformed tape or liquidbased adhesives, and EPDM roof membrane materials that are non-reinforced, fabricor scrim-reinforced, and fabric backed. Primers are also used as recommended for the specific adhesive. 1.4 This practice contains notes that are explanatory and are not part of the mandatory requirements of this practice. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Time-to-Failure (Creep-Rupture) of Adhesive Joints Fabricated from EPDM Roof Membrane Material

ASTM D4830/D4830M-98(2021) 屋面和防水用热塑性织物特性的标准试验方法

1.1 These test methods cover the procedures for characterizing thermoplastic fabrics (for example polyester, polyamide, polypropylene, and so forth) used in prefabricated roofing and waterproofing membranes. 1.2 Procedures appear in the following order: Section Unit Mass 3 Thickness 4 Breaking Load, Elongation, and Work-to-Break 5 Trapezoid Tearing Strength 6 Puncture Strength 7 Static Heat Stability 8 Dynamic Heat Stability 9 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Characterizing Thermoplastic Fabrics Used in Roofing and Waterproofing

BS EN 508-1:2021 金属板屋顶和覆层产品 钢、铝或不锈钢板自承式产品规范 钢

Roofing and cladding products from metal sheet. Specification for self-supporting products of steel, aluminium or stainless steel sheet. Steel

ASTM D7186-14(2021) 屋顶施工和维修的质量保证观测的标准实施规程

1.1 This practice covers procedures for performing visual monitoring of roofing construction to: 1.1.1 Establish guidelines for quality assurance observation practices; and 1.1.2 Define the role and responsibilities of the quality assurance observer. 1.2 This practice pertains to quality assurance observation of roofing projects and the report of information obtained from these observations. This practice is applicable to new construction or reroofing projects involving the installation of a new roof system, the removal of existing roofing and installation of a new roof system, or recovering an existing roof. It is also applicable to roofing projects involving repairs or scheduled maintenance to an existing roof. 1.3 This practice contains the following information: 1.3.1 The objectives of the quality assurance process; 1.3.2 The responsibilities and qualifications of the individual(s) involved in the observations of the roof construction or repair; 1.3.3 Identification and use of the basic tools or equipment required for the visual roof observation process; and 1.3.4 Monitoring, recording, and reporting procedures. 1.4 This practice addresses new construction or repair. This practice does not address the investigation, condition, or analysis of existing roofs. 1.5 This practice does not address practices of roof investigation, condition reporting, or analysis of preexisting roofs. 1.6 This practice does not pertain to quality control processes or techniques performed by persons or entities representing or under contract to the roofing contractor. The quality control process is separate and distinct from the quality assurance observation process. 1.7 Assessment of safe work practices or safety monitoring procedures followed by the contractor is outside the scope of this practice. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Quality Assurance Observation of Roof Construction and Repair