91.060.20 屋顶 标准查询与下载

BS EN 508-3:2021 金属板屋顶和覆层产品 钢、铝或不锈钢板自承式产品规范 不锈钢

Roofing and cladding products from metal sheet. Specification for self-supporting products of steel, aluminium or stainless steel sheet. Stainless steel

DS/EN 508-3:2021 金属板屋顶和覆层产品《钢、铝或不锈钢板自支撑产品规范》第3部分：不锈钢

Roofing and cladding products from metal sheet – Specification for self-supporting products of steel, aluminium or stainless steel sheet – Part 3: Stainless steel

EN 508-3:2021 金属薄板材制成的屋顶产品.钢,铝或不锈钢薄板自支撑产品规范.第3部分:不锈钢

This part of EN 508 specifies requirements for self-supporting products for roof covering, wall cladding, lining, liner tray and tile products for discontinuous laying made from stainless steel sheets with or without additional metallic and/or organic coatings. Sheets intended to be used with insulation and membranes are also covered. This document establishes general characteristics, definitions, classifications and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are dispatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions. This document applies to all discontinuously laid self-supporting external profiled sheets for roof covering, wall cladding, lining, liner trays and tile products with the exception of tiles with a surface area less than 1 m2 and produced by stamping. These profiled roof sheets are designed to keep wind, rain and snow out of the building and to transfer any resultant loads and infrequent maintenance loads to the structure. This document does not cover products for structural purposes, i.e. it does cover products used in structural class III (according to EN 1993-1-3), it does not cover products used in constructions of structural classes I and II (according to EN 1993-1-3) intended to contribute to the global or partial stability of the building structure by providing racking resistance or resistance to permanent static loads (excluding self-weight of the metal sheet). No requirements for supporting construction, design of roof or cladding, lining, tile system and execution of connections and flashings are included.

Roofing and cladding products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet - Part 3: Stainless steel

EN 508-1:2021 金属制屋顶产品.钢铝或不锈钢片的自支持产品规范.第1部分:钢

Roofing and cladding products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet - Part 1: Steel

OENORM EN 607-2021 由 PVC-U 制成的檐槽和配件 定义、要求和测试

Eaves gutters and fittings made of PVC-U - Definitions, requirements and testing

prEN 607-2021 由 PVC-U 制成的檐槽和配件 定义、要求和测试

Eaves gutters and fittings made of PVC-U - Definitions, requirements and testing

T/CSTM 00292-2021 建筑隔热保温涂层节能评价方法

本文件规定了隔热保温涂层自然环境下建筑节能评价的术语和定义、试验设备、试样、试验方法、试验结果及评价和试验报告。 本文件适用于对不同类型的隔热保温涂层在不同气候区的建筑节能效果进行测试与评价。

Energy-saving evaluation method for building insulating coatin

T/CCMSA 10719-2021 旋转门

本文件规定了旋转门的分类、规格与标记、材料与配件、要求、试验方法、检验规则、包装、标志、维护、运输和贮存。 本文件适用于公共建筑中供人通行的旋转门。

Revolving Doors

ASTM E1091-21 用于防护板的非金属蜂窝芯的标准规范

1.1?This specification is for nonmetallic honeycomb core used in the manufacture of adhesively bonded sandwich panels for tactical shelters. The materials are intended for adhesive bonding to aluminum facings using materials and processes defined by Practices E864 and E874, and

Standard Specification for Nonmetallic Honeycomb Core for Use in Shelter Panels

CSA A123.24-2021 模块化植被屋顶组件抗风性的标准测试方法

Standard test method for wind resistance of modular vegetated roof assembly

ASTM D7954/D7954M-15a(2021) 用无损电阻抗扫描仪测量屋顶和防水系统湿度的标准实施规程

Standard Practice for Moisture Surveying of Roofing and Waterproofing Systems Using Nondestructive Electrical Impedance Scanners

T/CECS 796-2021 屋面结构雪荷载设计标准

主要技术内容是：总则、术语和符号、基本规定、基本雪压、屋面积雪分布系数、局部雪荷载等。

Design criteria for snow loads on roof structures

T/CCMSA 20216-2020 建筑金属屋（墙）面围护系统技术标准

包括：适用范围、引用规范、术语和定义、基本规定、载荷、材料、设计、制作、安装与验收、性能检测、实验室检测、日常维护等。

Technical Standard for Metal Roof and Wall Cladding System

T/ZZB 1984-2020 预应力混凝土空心板

本文件规定了预应力混凝土空心板的规格尺寸与标记、基本要求、技术要求、试验方法、检验规则、标志、堆放、运输和产品合格证、质量承诺。 本文件适用于抗震设防烈度不大于8度、环境类别为一类及二a类的工业与民用建筑用预应力混凝土空心板（以下简称空心板）。

Prestressed concrete hollow-core slabs

ASTM D8257/D8257M-20 陡坡屋顶用机械连接聚合屋顶垫层的标准规范

Standard Specification for Mechanically Attached Polymeric Roof Underlayment Used in Steep Slope Roofing

ASTM E2950-14(2020) 金属罩系统标准规范

1.1 This specification includes the following: 1.1.1 Structural framing, 1.1.2 Canopy Deck System, 1.1.3 Drainage system, 1.1.4 Fascia panels, 1.1.5 Accessories and trim, and 1.1.6 Canopy concrete foundations and accessories. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Metal Canopy Systems

ASTM D7158/D7158M-20 沥青瓦抗风性的标准试验方法（抗拔力/抗拔力法）

1.1 This test method covers the procedure for calculating the wind resistance of asphalt shingles when applied in accordance with the manufacturer’s instructions and sealed under defined conditions. Shingle designs that depend on interlocking or product rigidity to resist the wind cannot be evaluated using this test method. The method calculates the uplift force exerted on the shingle by the action of wind at a specified velocity, and compares that to the mechanical uplift resistance of the shingle. A shingle is determined to be wind resistant at a specified basic wind speed when the measured uplift resistance exceeds the calculated uplift force for that velocity (3-s gust, ASCE 7). 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Wind Resistance of Asphalt Shingles (Uplift Force/Uplift Resistance Method)

20/30393547 DC BS EN 1873-1 屋顶预制配件 单独的塑料屋顶灯 第 1 部分：产品规格和测试方法

BS EN 1873-1. Prefabricated accessories for roofing. Individual plastic rooflights - Part 1. Product specification and test methods

ASTM C1568-08(2020) 混凝土和粘土瓦片抗风性的标准试验方法（机械抗拔力法）

1.1 This test method covers a procedure to determine the mechanical uplift resistance of concrete and clay roof tiles, which relates to the wind resistance of an air-permeable roof tile system as applied to a roof. 1.2 The procedure covers mechanically-fastened attachment systems, adhesive-set attachment systems, and mortar-set attachment systems, or combinations of attachment systems, that are used to apply tile to a roof. 1.3 The values stated in inch pound units are to be regarded as the standard. The values in parentheses are given for reference only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Wind Resistance of Concrete and Clay Roof Tiles (Mechanical Uplift Resistance Method)

ASTM D6225/D6225M-98(2020) 矿物表层屋面颗粒盖标准试验方法

1.1 This test method covers the determination of the hiding power of granules on a mineral-surfaced roofing sheet. The test is used primarily after an abrasion test has been conducted to determine the portion of asphaltic compound that has been exposed as a result of the abrasion test. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Granule Cover of Mineral-Surfaced Roofing