91.060.20 屋顶 标准查询与下载

ASTM D6757/D6757M-18(2023) 陡坡屋顶用含无机纤维衬垫毛毡的标准规范

Standard Specification for Underlayment Felt Containing Inorganic Fibers Used in Steep-Slope Roofing

ASTM D41/D41M-11(2023) 屋顶、防潮和防水用沥青底漆标准规范

Standard Specification for Asphalt Primer Used in Roofing, Dampproofing, and Waterproofing

DB11/T 848-2023 压型金属板屋面工程施工质量验收标准

Acceptance standard for construction quality of profiled metal sheet roofing engineering

GSO ASTM E2777:2023 植物（绿色）屋顶系统标准指南

  Scope is not provided for this standard

Standard Guide for Vegetative (Green) Roof Systems

GSO ASTM D8014:2023 植物屋顶系统中使用的薄膜选择标准指南

  Scope is not provided for this standard

Standard Guide for Selection of Membranes Used in Vegetative Roofing Systems

BS EN 14437:2022 测定屋顶安装的粘土或混凝土瓦的抗隆起力 屋顶系统测试方法

1   Scope This document specifies a test method to establish the uplift resistance of installed clay or concrete tiles for roofing, complying with the relevant product standard, EN 490 or EN 1304, which are unfixed or mechanically fixed to the substructure. NOTE The test method has been developed for clay or concrete tiles for roofing, but can apply to other discontinuously laid small elements , such as: slates; fibre cement slates; stones; and, adapted accordingly, to photovoltaic and solar thermal panels. The test method is applicable to mechanical fixings such as clips, hooks, screws and nails. The method is not applicable to fixed tiles having fixing patterns with less than every third tile fixed. The test method is not applicable to under and over tiles. Examples of these tiles are given in Annex F.

Determination of the uplift resistance of installed clay or concrete tiles for roofing. Roof system test method

KS F 4733-2022 钢纤维混凝土墙板

Steel fiber reinforced concrete panel for wall

KS F 2269-2022 屋顶覆盖物防火试验方法

Methods for fire tests of roof coverings

ASTM D7655/D7655M-12(2022) 用作薄膜屋顶系统压载物的骨料尺寸的标准分类

1.1 This classification defines the aggregate size designations and ranges in mechanical analyses for standard sizes of aggregate used as ballast for membrane roof systems. 1.2 The text of this classification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.3 With regard to sieve sizes and the size of aggregate as determined by the use of testing sieves, the values in inchpound units are shown for the convenience of the user; however, the standard sieve designations shown in parentheses are the standard values as stated in Specification E11. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification for Size of Aggregate Used as Ballast for Membrane Roof Systems

T/ZS 0338-2022 卷材屋面工程防水施工作业管理规范

前  言　 1  范围　 2  规范性引用文件　 3  术语和定义　 4  基本要求　 5  人员　 6  材料　 7  作业条件　 8  操作流程　 9  质量控制　 10  成品保护　 11  安全防护　 附录A（规范性）屋面工程防水施工操作流程图　

Specification for management of waterproofing construction of coil roofing engineering

KS F 4750-2022 沥青油毡瓦片

Asphalt shingles

KS F 4522-2022 屋顶排水沟

Roof drains

KS F 4913-2022 机织织物沥青屋顶

Woven fabrics asphalt roofings

ASTM D6918-09(2022) 测试压接条件下垂直带材排水管的标准试验方法

1.1 This test method is a performance test that measures the effect crimping has on the ability of vertical strip drains to transmit water parallel to the plane of the drain. 1.2 This test method is applicable to all vertical strip drains. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Testing Vertical Strip Drains in the Crimped Condition

22/30455142 DC BS EN 508-3:2021 AMD1 金属板屋顶和覆层产品 钢、铝或不锈钢板自承式产品规范 第 3 部分：不锈钢

BS EN 508-3:2021 AMD1. Roofing and cladding products from metal sheet. Specification for self-supporting products of steel, aluminium or stainless steel sheet - Part 3. Stainless steel

T/CIEEMA 005-2022 村镇民用建筑装配式瓦型屋面部品

1  范围 2  规范性引用文件 3  术语和定义 4  分类和标记 5  一般规定 6  原材料 7  技术要求 8  试验方法 9  检验规则 10  产品标记、堆放和运输

Prefabricated tile roof parts of rural houses

ASTM D6754/D6754M-15(2022) 酮乙烯酯基薄屋面的标准规范

1.1 This specification covers flexible sheet made from ketone ethylene ester (KEE) as the primary polymer intended for use in single-ply roofing membrane exposed to the weather. The sheet shall be reinforced with fabric. 1.2 In-place roof system design criteria, such as fire resistance, field-seaming strength, material compatibility, uplift resistance, in-situ shrinkage, among others, are factors that must be considered but are beyond the scope of this specification. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 The following precautionary caveat pertains to the test methods portion only, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Ketone Ethylene Ester Based Sheet Roofing

GSO EN 12951:2022 屋顶预制配件 永久固定屋顶梯子 产品规范和试验方法

This document applies to permanently fixed ladders made of metal which are permanently installed on the load-bearing construction of pitched roofs and which may be stepped or walked on for purposes of inspection, maintenance and repair of equipment installed above the roof surface. This document specifies essential dimensions, materials to be used, requirements with respect to the load-bearing capacity, and the extent of testing. This document does not cover walkways, single treads, single steps or roof ladders that are not permanently fixed nor does it cover fire escape ladders.

Prefabricated accessories for roofing - Permanently fixed roof ladders - Product specification and test methods

ASTM E1680-16(2022) 通过外部金属屋顶板系统的空气泄漏率的标准试验方法

1.1 This test method covers the determination of the resistance of exterior metal roof panel systems to air infiltration resulting from either positive or negative air pressure differences. The test method described is for tests with constant temperature and humidity across the specimen. This test method is a specialized adaption of Test Method E283. 1.2 This test method is applicable to any roof area. This test method is intended to measure only the air leakage associated with the field of the roof, including the panel side laps and structural connections; it does not include leakage at the openings or perimeter or any other details. 1.3 The proper use of this test method requires knowledge of the principles of air flow and pressure measurements. 1.4 The text of this test method references notes and footnotes excluding tables and figures, which provide explanatory material. These notes and footnotes shall not be considered to be requirements of the test method. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 7. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Rate of Air Leakage through Exterior Metal Roof Panel Systems

ASTM D6917-16(2022) 预制垂直排水管（PVD）试验方法选择的标准指南

1.1 This guide provides recommendations for the selection of appropriate test methods for prefabricated vertical geocomposite drains (sometimes referred to as wick drains) used in geotechnical engineering applications to provide consistency in data reporting. 1.2 This guide includes test methods for all types of prefabricated geocomposite drains manufactured in a plant and consisting of a polymeric core structure with a synthetic fabric (geotextile) jacket for filtration. 1.3 This guide is intended to aid all personnel involved in the selection, manufacture, installation, or evaluation of prefabricated vertical drains. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Selection of Test Methods for Prefabricated Vertical Drains (PVD)