A83 包装方法 标准查询与下载

BS EN ISO 8318:2002 包装.满装运输包装件和成组装运.用变频进行正弦波振动试验

This International Standard specifies two methods for carrying out a sinusoidal vibration test on a complete, filled transport package or unit load using a variable frequency. These tests may be used to assess the performance of a package or an unit load in terms of its strength or the protection that it offers to its contents when it is subjected to vertical vibration. Each may be performed either as a single test to investigate the effects of vertical vibration or as part of a sequence of tests designed to measure the ability of a package or unit load to withstand a distribution system that includes a vibration hazard.

Packaging. Complete, filled transport packages and unit loads. Sinusoidal vibration tests using a variable frequency

BS EN ISO 2244:2002 包装.满装运输包装件和成组装运.水平冲击试验

This International Standard specifies methods of horizontal impact testing (horizontal or inclined plane test and pendulum test) on a complete, filled transport package or a unit load. The test may be performed either as a single test to investigate the effects of horizontal impact or as part of a sequence of tests designed to measure the ability of a package or a unit load to withstand a distribution system that includes a horizontal impact hazard.

Packaging. Complete, filled transport packages and unit loads. Horizontal impact tests

ASTM D3078-02(2008)e1 起泡法测定软包装泄漏的标准试验方法

1.1 This test method covers the determination of gross leaks in flexible packaging containing a headspace gas. Test sensitivity is limited to 1 × 10−5 atm cm3/s (1 × 10−6 Pa m3/s) or even less sensitive as indicated in a recent interlaboratory test (reported in Section 12). 1.2 Small leaks may not be detected by this procedure. Viscoelastic effects on the products, or entrapped air, become significant and prevent passage through small openings. Positive pressure inside the pouch after the vacuum is drawn may force the product to plug small leaks. The size of the leak that can be detected is dependent upon the products contained, the nature of the packaging material, and the test parameters selected. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Leaks in Flexible Packaging by Bubble Emission

ASTM D3078-02 起泡法测定软包装泄漏的标准试验方法

1.1 This test method covers the determination of gross leaks in flexible packaging containing a headspace gas. Test sensitivity is limited to 1 x 10-5 atm cm3/s (1 x 10-6 Pa m3/s) or even less sensitive as indicated in a recent interlaboratory test (reported in Section 12).1.2 Small leaks may not be detected by this procedure. Viscoelastic effects on the products, or entrapped air, become significant and prevent passage through small openings. Positive pressure inside the pouch after the vacuum is drawn may force the product to plug small leaks. The size of the leak that can be detected is dependent upon the products contained, the nature of the packaging material, and the test parameters selected.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Leaks in Flexible Packaging by Bubble Emission

KS T 1305-2001 防潮包装材料的透水性试验方法

이 규격은 방습 포장 재료의 투습도 시험 방법에 대하여 규정한다.

Testing method for permeability of damp proof packing materials

ISO 13355:2001 包装 满装的运输包装和单元货物 随机垂直振动试验

This International Standard specifies a method to carry out a vertical random vibration test on a complete, filled transport package(s) and unit loads using a random excitation. This test may be used to assess the performance of a package in terms of its strength or the protection that it offers to its contents when it is subjected to vertical vibration. It may be performed either as a single test to investigate the effects of vertical vibration or as a part of a sequence of tests designed to measure the ability of a test item to withstand a distribution system that includes a vibration hazard. NOTE In the following text a package or unit load is called a test item. note: 1) The treatment of random vibration theory can be found in IEC 60068-2-64 (see reference [3] in the Bibliography).

Packaging - Complete, filled transport packages and unit loads - Vertical random vibration test

DIN EN ISO 2233:2001 包装.满运输包装和单位负载.试验条件

Packaging - Complete, filled transport packages and unit loads - Conditioning for testing (ISO 2233:2000); German version EN ISO 2233:2001

BS EN 13054:2001 包装.完全填充运输包装.包裹重心测定方法

This standard specifies two methods of determining the location of the centre of gravity of flat sided rigid packages. In the following text, a package is called "a test item".

Packaging - Complete, filled transport packages - Test methods for the determination of the centre of gravity of a package

ASTM D3065-01(2006) 气溶胶制器可燃性的标准试验方法

These test methods were developed so that the Open Drum Test could be abandoned as a meaningful guide in establishing flammability hazards.1.1 These test methods cover the determination of flammability hazards for aerosol products.1.2 These test methods appear in the following order: SectionFlame Projection Test4 to 7Closed Drum Test8 to 101.3 This standard should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Flammability of Aerosol Products

ASTM D6573/D6573M-01(2007) 通用钢丝捆扎货运箱的标准规范

1.1 This specification covers the fabrication of new wirebound general purpose (GP) panelboard (hereafter referred to as wirebound boxes) shipping boxes intended for use as containers for domestic and overseas shipment of general materials and supplies, not exceeding 500 lb [226.8 kg] for class 1 domestic, 400 lb [181.4 kg] for Class 2 overseas shipments or 300 lb [136.0 kg] for Class 3 extreme distribution hazard conditions or military contingency purposes.1.2 Wirebound box performance is dependent on its fabricated components; therefore, a variety of types, classes, styles, and treatments reflecting varied performance are specified. This specification does not cover wirebound box performance under all atmosphere, handling, shipping, and storage conditions. Wirebound boxes in compliance with Hazardous Material Modal Regulations or United States Code of Federal Regulations (CFRs) are found in the Supplementary Requirements.1.3 The use of other construction methods or techniques are acceptable and shall be permitted, provided the resulting packaging systems are of equal or better performance than would result from the use of these specified materials and procedures. The appropriate Practice D 4169 distribution cycle(s) can be used to develop comparative procedures and criteria.1.4 Units8212;The values stated in inch-pound units are to be regarded as standard. The SI values given in brackets are mathematical. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. See IEEE/SI 10 for conversion of units.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for General Purpose Wirebound Shipping Boxes

ASTM D3065-01 气溶胶制器可燃性的标准试验方法

1.1 These test methods cover the determination of flammability hazards for aerosol products.1.2 These test methods appear in the following order: SectionFlame Projection Test4 to 7Closed Drum Test8 to 101.3 This standard should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Flammability of Aerosol Products

JIS Z 0203:2000 装箱的货物.试验条件

この規格は，包装貨物の落下試験，圧縮試験，振動試験などの試験に先立って行う前処置方法について規定する。

Packaged freights -- Conditioning for testing

KS T 1308-2000 大纸袋缝合强度试验方法

이 규격은 대형 지대(이하 지대라 한다.)의 바늘 땀 강도 시험 방법에 대하여 규정한다.

Testing method of sew-up strength for 1arge-sized paper bag

DIN 55457-1:2000 包装试验.聚烯烃容器.抗应力开裂性.温度程序

The document specifies tests of containers made of polyolefines within the temperature procedure. The test shows the tension cracking resistance of containers and their closures. The requirements for stacking are not taken into account.

Packaging test - Containers made from polyolefines - Part 1: Tension cracking resistance; temperature procedure

DIN 55457-2:2000 包装试验.聚烯烃容器.抗应力开裂性.第2部分:压力温度程序

The document specifies tests of containers made of polyolefines within the pressure-temperature procedure. The test shows the tension cracking resistance of containers made of polyolefines.

Packaging test - Containers made from polyolefines - Part 2: Tension cracking resistance; pressure-temperature procedure

ISO 2873:2000 包装 满装的运输包装和单元货物 低压试验

This International Standard specifies a method for subjecting complete, filled transport packages and unit loads to conditions of low air pressure similar to those encountered in aircraft. This method is applicable to complete, filled transport packages and unit loads which are intended to be transported in pressurized aircraft flying at any altitude and in unpressurized aircraft flying at 3 500 m or less.

Packaging - Complete, filled transport packages and unit loads - Low pressure test

ISO 2233:2000 包装 满装的运输包装和单元货物 试验条件

This International Standard specifies a method for the conditioning of complete, filled, transport packages and unit loads.

Packaging - Complete, filled transport packages and unit loads - Conditioning for testing

ISO 2244:2000 包装 满装的运输包装和单元货物 水平冲击试验

This International Standard specifies methods of horizontal impact testing (horizontal or inclined plane test and pendulum test) on a complete, filled transport package or a unit load. The test may be performed either as a single test to investigate the effects of horizontal impact or as part of a sequence of tests designed to measure the ability of a package or a unit load to withstand a distribution system that includes a horizontal impact hazard.

Packaging - Complete, filled transport packages and unit loads - Horizontal impact tests

ISO 2247:2000 包装 满装的运输包装和单元货物 固定低频率振动试验

This International Standard specifies methods to carry out vibration tests on complete, filled transport packages or unit loads using sinusoidal excitation at fixed frequency. These tests may be used to assess the performance of packages and unit loads in terms of the strength or the protection that they offer to their contents when subjected to low frequency vibration. These tests may be performed either as a single test to investigate the effects of low frequency vibration or as a part of a sequence of tests designed to measure the ability of a package or unit load to withstand a distribution system that includes a vibration hazard at low frequency or repetitive shocks.

Packaging - Complete, filled transport packages and unit loads - Vibration tests at fixed low frequency

ISO 2875:2000 包装 满装的运输包装和单元货物 喷水试验

This International Standard specifies a method for testing the resistance of a complete, filled transport package or a unit load to water spray or the protection it gives to its contents from water spray. It may also be used to precondition a complete, filled transport package or a unit load prior to another test to investigate reduction in strength caused by exposure to water. The test is performed on the test specimen as prepared for transport and may form part of a test sequence.

Packaging - Complete, filled transport packages and unit loads - Water-spray test