F81 通用核仪器 标准查询与下载

ISO 3999:2004 辐射防护.工业用Υ辐射照相设备.性能、设计和试验规范

This International Standard specifies the performance, design and test requirements of apparatus for gamma radiography with portable, mobile and fixed exposure containers of the various categories defined in Clause 4. It applies to apparatus designed to allow the controlled use of gamma radiation emitted by a sealed radioactive source for industrial radiography purposes, in order that persons will be safeguarded when the apparatus is used in conformity with the regulations in force regarding radiation protection. It is emphasised, however, that so far as transport of apparatus and sealed radioactive source is concerned, compliance with this International Standard is no substitute for satisfying the requirements of relevant international transport regulations (IAEA Regulations for the safe transport of radioactive materials: IAEA-STI-PUB 998, Safety Standards Series No. ST-1 and No. ST-2, and/or the relevant national transport regulations). The operational use of apparatus for industrial gamma radiography is not covered by this International Standard. Users of this equipment shall comply with national regulations and codes of practice.

Radiation protection - Apparatus for industrial gamma radiography - Specifications for performance, design and tests

BS ISO 4037-4:2004 校准剂量仪和剂量率仪及确定其光子能量响应的Χ和γ参考辐射.低能X参考辐射场中场所剂量计和个人剂量计的校准

This part of ISO 4037 gives guidelines on additional aspects of the characterization of low energy photon radiations. This part of ISO 4037 also describes procedures for calibration and determination of the response of area and personal dose(rate)meters as a function of photon energy and angle of incidence. This part of ISO 4037 concentrates on the accurate determination of conversion coefficients from air kerma to Hp(10) and H(10) for the spectra of low energy photon radiations. As an alternative to the use of conversion coefficients, the direct calibration in terms of these quantities by means of appropriate reference instruments is described.

X and gamma reference radiation for calibrating dosemeters and doserate meters and for determining their response as a function of photon energy - Calibration of area and personal dosemeters in low energy X reference radiation fields

DIN EN 14181:2004 固定源辐射.自动测量系统的质量保证

This standard specifies procedures that shall be carried out to cover quality assurance of automated measuring systems (AMS) installed on industrial plants for the determination of the flue gas components and other flue gas parameters. This includes the calibration and the determination of the variability of the measured values for comparison with stated uncertainties by means of parallel measurements using a standard reference method. Furthermore, the standard includes a procedure for operational activities necessary to maintain the required quality of the measurement results, as well as a procedure for the annual surveillance tests on the AMS.

Stationary source emissions - Quality assurance of automated measuring systems; German version EN 14181:2004

JB/T 6215-2004 工业用X射线管 系列型谱

本标准规定了工业用x射线管的分类和系列型谱。 本标准适用于工业用x射线管(包括材料探伤用、结构分析用、荧光光谱分析用、测厚用x射线管系列)。

Industrial X-ray Tube Series Spectrum

JB/T 6221-2004 工业X射线探伤机电气通用技术条件

本标准规定了工业x射线探伤机电气系统通用技术要求、检查与试验。 标准适用于额定电源电压为交流220V、380V或220V/380V，频率为50Hz的工业x射线探伤机的电气系统。

General electrical technical specifications for industrial X-ray flaw detectors

JB/T 6220-2004 射线探伤用密度计

本标准规定了射线探伤用密度计的产品型号、要求、试验方法、检验规则和标志、包装、运输、贮存等内容。 本标准适用于光透式射线探伤用密度计。

Density meter for radiography

DLA SMD-5962-02544 REV A-2004 单片硅线性微电路低噪声宽带运算放大器

This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN.

MICROCIRCUIT, LINEAR, LOW NOISE, WIDEBAND, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON

IEC 60405:2003 核仪表.放射性测量仪表的结构要求和分类

Specifies constructional requirements for the design of instruments and the radiation protection to be provided in the case of radiometric gauges. Special attention is drawn to the stability of the source housing in the event of fire.

Nuclear instrumentation - Constructional requirements and classification of radiometric gauges

ANSI N323B-2003 已安装的辐射防护仪器仪表试验和校准.邻近背景操作用便携式测量仪器

Performance requirements for portable instruments for radiation levels near background.

Installed Radiation Protection Instrumentation Test and Calibration - Portable Survey Instruments for Near Background Operation

DLA SMD-5962-02545-2003 单片硅辐射硬化线性微电路双宽带低噪声电压反馈运算放大器

This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN.

MICROCIRCUIT, LINEAR, RADIATION HARDENED, DUAL, WIDEBAND, LOW NOISE, VOLTAGE FEEDBACK OPERATIONAL AMPLIFIER, MONOLITHIC SILICON

ANSI N42.31-2003 离子辐射的宽能带隙半导体探测器的分辨和功效的测量规程

Measurement and test procedures are established for wide-bandgap semiconductor detectors such as cadmium-telluride (CdTe) cadmium-zinc-telluride (CdZnTe), and mercuric iodide (HgI2) that can be used at room temperature for the detection and quantitative

Measurement Procedures for Resolution and Efficiency of Wide-Bandgap Semiconductor Detectors of Ionizing Radiation

ANSI N42.34-2003 放射性核素检测和识别用手持式仪器的性能标准

This standard addresses instruments that can be used for homeland security applications to detect and identify radionuclides, for gamma dose rate measurement, and for indication of neutron radiation. This standard specifies general requirements and test procedures, radiation response requirements, and electrical, mechanical, and environmental requirements. Successful completion of the tests described in this standard should not be construed as an ability to successfully identify all isotopes in all environments.

Performance Criteria for Hand-held Instruments for the Detection and Identification of Radionuclides

ANSI N42.33-2003 国家安检用辐射检测仪器

This standard establishes performance and design criteria, test and calibration requirements, and operating and training instruction requirements for portable radiation detection instruments used for detection and measurement of radioactive substances for the purposes of interdiction and emergency response. The appendices of this standard provide reference information. This standard includes:Design and performance requirements for specific instrument types and applicationsType testing and certification requirements for these instruments;Calibration and test intervalsRequired calibration equipmentRequired documentation, including the instrument instruction manual

Radiation Detection Instrumentation for Homeland Security

ANSI N42.32-2003 国家安检用人员辐射警报检测器的性能标准

This standard describes design and performance criteria along with testing methods for evaluating the performance of instruments for homeland security that are pocket sized and carried on the body for the purpose of detecting the presence and magnitude of radiation. This standard specifies the performance criteria for radiation detection and measurement instruments that may be used in a variety of environmental conditions. The performance criteria contained in this standard are meant to provide a means for verifying the capability of these instruments to reliably detect significant changes above background levels of radiation and alert the user to these changes.

Performance Criteria for Alarming Personal Radiation Detectors for Homeland Security

IEEE/ANSI N42.17A-2003 标准环境条件中使用的保健物理学便携式仪器用美国国家标准化性能规范

American National Standard Performance Specifications for Health Physics Instrumentation-Portable Instrumentation for Use in Normal Environmental Conditions

ANSI N42.30-2002 氚监测器的性能规范

Contains performance requirements and test methods for tritium motors.

Performance Specification for Tritum Monitors

ANSI N42.28-2002 现场γ射线测量用锗探测器的校准

Covers performance criteria of measurement techniques for efficiency calibration.

Calibration of Germanium Detectors for In-Situ Gamma-Ray Measurements

IEC 61559-2:2002 核设施中的辐射.连续监测辐射和/或放射性水平的中心系统.第2部分:对卸料,环境,意外事件或紧急事故监测功能的要求

Identifies requirements pertinent to the integration of the monitoring functions into a centralized system. Considers requirements for general and design characteristics, electrical performance requirements and tests, mechanical performance requirements

Radiation in nuclear facilities - Centralized systems for continuous monitoring of radiation and/or levels of radioactivity - Part 2: Requirements for discharge, environmental, accident, or post-accident monitoring functions

IEEE/ANSI N42.28-2002 现场伽马射线测量用锗探测器的美国国家标准校正

American National Standard Calibration of Germanium Detectors for In-Situ Gamma-Ray Measurements

ANSI N43.2-2001 X射线衍射和荧光分析设备的辐射安全

Reviews the types of injuries resulting from accidental exposure to ionizing radiation resulting from the operation of analytical x-ray diffraction and fluorescence equipment, establishes equipment design criteria, sets up requirements for approved opera

Radiation Safety for X-ray Diffraction and Fluorescence Analysis Equipment