J05 结构要素 标准查询与下载

GB/T 6403.1-1986 球面半径

本标准规定一般机械零件的球面半径尺寸系列。

Radii of sphere surfaces

GB/T 6403.4-1986 零件倒圆与倒角

本标准适用于一般机械切削加工零件的外角和内角的倒圆、倒角。不适用于有特殊要求的倒圆、倒角。

Rounding and chamfered of parts

NF E03-055*NF ISO 965-4:2021 ISO一般用途米制螺纹. 公差. 第4部分: 热浸镀锌外螺纹的极限尺寸、与其相配的内螺纹镀锌后攻丝、内螺纹的公差带位置为H或G

ISO general purpose metric screw threads - Tolerances - Part 4 : limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing

DIN ISO 965-1:2017 ISO通用米制螺纹.公差.第1部分:原则和基本数据(ISO 965-1-2013)

ISO general purpose metric screw threads - Tolerances - Part 1: Principles and basic data (ISO 965-1:2013)

DIN 34817:2017 米制螺纹焊接螺钉

Weld screws with metric thread

BS ISO 2902:2016 ISO公制梯形螺纹 总平面图

ISO metric trapezoidal screw threads. General plan

BS ISO 2901:2016 ISO公制梯形螺纹. 基本和设计轮廓

ISO metric trapezoidal screw threads. Basic and design profiles

BS ISO 2903:2016 ISO公制梯形螺纹. 公差

ISO metric trapezoidal screw threads. Tolerances

DIN 76-1:2016 符合DIN 13-1的ISO米制螺纹的螺纹尾部和螺纹切槽

Thread run-outs and thread undercuts - Part 1: For ISO metric threads in accordance with DIN 13-1

GOST 10727-2015 单向玻璃螺纹. 规格

Unidirectional glass threads. Specifications

GOST ISO 1478-2015 自攻螺纹

Tapping screws thread

NF E03-051*NF ISO 965-1:2013 ISO一般用途公制螺纹.公差.第1部分:原理和基本数据

ISO general purpose metric screw threads - Tolerances - Part 1: principles and basic data

DIN 13-51:2013 ISO通用米制螺纹. 第51部分:过渡配合用外螺纹 (模型:紧密配合用螺纹). 公差, 极限偏差, 尺寸极限

ISO general purpose metric screw threads - Part 51: External screw threads for transition fits (former: screw threads for interference fit) - tolerances, limit deviations, limits of sizes

ISO 965-1:2013 ISO通用米制螺纹.公差.第1部分：原理和基本数据

This part of ISO 965 specifies a tolerance system for ISO general purpose metric screw threads (M) according to ISO 261. The tolerance system refers to the basic profile according to ISO 68-1.

ISO general purpose metric screw threads.Tolerances.Part 1: Principles and basic data

JIS B 0217-1:2013 ISO公制梯形螺纹.公差.第1部分:原理和基本数据

This Standard specifies a tolerance system for ISO metric trapezoidal screw threads (Tr) according to JIS B0216-2. This tolerance system refers to the basic profile and the maximum material profiles according to JIS B0216-1, and the basic dimensions according to JIS B0216-3; however, it does not apply to trapezoidal screw threads with special requirements on axial displacement, for example, lead screws.

ISO metric trapezoidal screw threads.Tolerances .Part 1: Principles and basic data

JIS B 0217-2:2013 ISO公制梯形螺纹.公差.第2部分:外部和内部螺纹的极限尺寸

This Japanese Industrial Standai'd specifies a tolerance system for ISO metric trapezoidal screw threads (Tr) specified in JIS B0216-2. The limit of size according to this Standard does not apply to trapezoidal screw threads with special requirements on axial displacement, for example, lead screws.

ISO metric trapezoidal screw threads.Tolerances .Part 2: Limits of sizes for external and internal screw thread

DIN 78:2013 螺栓尾部的凸度

Protrusions of bolt ends

SAE J476-2013 干密封管螺纹

This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying the continued suitability of technical guidance. Dry Seal threads should be in a ccordance with ASME B1.20.3.The Dryseal American Standard Taper Pipe Thread, the Dryseal American fuel Internal Straight Pipe Thread and the Dryseal American intermediate internal Straight Pipe Thread covered by this standard conform with the American Standard ASA-B2.2. The Dryseal SAE-Short Taper Pipe thread in this standard conforms with the Dryseal American Standard Taper pipe thread except for the length of thread, which is sho

Dryseal Pipe Threads

ANSI/ASME B1.20.1-2013 通用的管螺纹(英制)

Pipe Threads, General Purpose (Inch)

DIN 13-51:2012 ISO通用米制螺纹. 第51部分:过渡配合用外螺纹 (模型:紧密配合用螺纹); 公差, 极限偏差, 尺寸极限

ISO general purpose metric screw threads - Part 51: External screw threads for transition fits (former: screw threads for interference fit); tolerances, limit deviations, limits of sizes