J05 结构要素 标准查询与下载

AIA/NAS NAS 43-2006 Rev. 11 联邦科学委员会:5365 螺栓螺杆间隔套

DASH -2 INACTIVE FOR DESIGN AFTER 1 NOV. 1945. LOW CARBON STEEL SPACERS INACTIVE FOR DESIGN AFTER 15 NOV. 1952. NORMALIZED ALLOY SPACERS INACTIVE FOR DESIGN AFTER 15 AUG. 1962. USE ACTIVE NAS43 SPACERS IN DESIGN. FOR DESCRIPTION OF STATUS NOTES SEE NAS380

Spacer, Sleeve - Screw and Bolt FSC 5365; Rev. 11

KS B ISO 13766:2005 土方机械.电磁兼容性

이 규격에서는 KS B ISO 6165에서 정의한 토공 기계의 전자파 적합성 평가에 대한

Earth-moving machinery-Electromagnetic compatibility

BS EN 10226-3:2005 螺纹上有压力密封接缝的管螺纹.用极限量规验证

This document specifies a process using limit gauges, for the validation of taper internal and external threads and parallel internal threads on piping systems components and other products, the dimensions and tolerances of which are detailed in EN 10226-1 and prEN 10226-2. The gauging system described may not be suitable, without special precautions, for gauging of threads on injection moulded plastic workpieces. This document does not cover completely all the requirements necessary for full control of thread quality and dimensions. Additional control of tools and equipment and visual inspection during production are required to ensure complete compliance with EN 10226-1 and prEN 10226-2, for example the length of useful thread on internally threaded workpieces should be checked by direct measurement. Annex A gives a summary of the gauges included in this document, together with details of the thread elements controlled by each gauge and gauge identification numbers. In the event of a dispute over compliance with the requirements of EN 10226-1 and prEN 10226-2, the gauges in this document are to be considered as decisive for the thread elements which they control on the workpiece.

Pipe threads where pressure-tight joints are made on the threads - Verification by means of limit gauges

NF E03-150*NF ISO 1502:2005 ISO一般用途米制螺纹.量规和量规检验

ISO general-purpose metric screw threads - Gauges and gauging.

DIN 13-21:2005 ISO通用米制螺纹.第21部分:优选公差级的细牙螺纹极限尺寸.标称直径1mm～24.5mm

This standard applies to the ISO general purpose metric screw threads with a basic profile according to DIN ISO 68-1. It contains the limits of sizes for fine threads from 1 mm to 24,5 mm nominal sizes with the prefered tolerance classes.#,,#

ISO general purpose metric screw threads - Part 21: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 1 mm to 24,5 mm

DIN 13-22:2005 ISO通用米制螺纹.第22部分:优选公差级的细牙螺纹极限尺寸.标称直径25～52mm

ISO general purpose metric screw threads - Part 22: Limits of sizes for fine pitch threads with the prefered tolerance classes; Nominal diameter from 25 mm to 52 mm

DIN 13-25:2005 ISO通用米制螺纹.第25部分:优选公差级的细牙螺纹的极限尺寸.标称直径182mm至250mm

This standard applies to the ISO general purpose metric screw threads with a basic profile according to DIN ISO 68-1. It contains the limits of sizes for fine threads from 182 mm to 250 mm nominal sizes with the prefered tolerance classes.

General purpose ISO metric screw threads - Part 25: Limits of sizes for fine pitch threads with the prefered tolerance classes - Nominal diameter from 182 mm to 250 mm

DIN 13-26:2005 ISO通用米制螺纹.第26部分:优选公差级的细牙螺纹极限尺寸.标称直径252～1000mm

This standard applies to the ISO general purpose metric screw threads with a basic profile according to DIN ISO 68-1. It contains the limits of sizes for fine threads from 252 mm to 1000 mm nominal sizes with the prefered tolerance classes.

ISO general purpose metric screw threads - Part 26: Limits of sizes for fine pitch threads with the prefered tolerance classes; Nominal diameter from 252 mm to 1000 mm

DIN 13-51:2005 ISO通用米制螺纹.第51部分:过渡配合用外螺纹(模型:紧密配合用螺纹).公差、极限偏差、尺寸极限

The standard specifies tolerance classes for external screw thread.

ISO general purpose metric screw threads - Part 51: External screw threads for transition fits (former: screw threads for interference fit); tolerances, limit deviations, limits of sizes

DIN 13-24:2005 ISO通用米制螺纹.第24部分:优选公差级的细牙螺纹的极限尺寸.标称直径112mm至180mm

This standard applies to the ISO general purpose metric screw threads with a basic profile according to DIN ISO 68-1. It contains the limits of sizes for fine threads from 112 mm to 180 mm nominal sizes with the prefered tolerance classes.

General purpose ISO metric screw threads - Part 24: Limits of sizes for fine pitch threads with the prefered tolerance classes - Nominal diameter from 112 mm to 180 mm8

DIN 13-23:2005 ISO通用米制螺纹.第23部分:优选公差级的细牙螺纹的极限尺寸.标称直径53mm至110mm

This standard applies to the ISO general purpose metric screw threads with a basic profile according to DIN ISO 68-1. It contains the limits of sizes for fine threads from 53 mm to 110 mm nominal sizes with the prefered tolerance classes.

General purpose ISO metric screw threads - Part 23: Limits of sizes for fine pitch threads with the prefered tolerance classes - Nominal diameter from 53 mm to 110 mm

DIN 3858:2005 管箍用惠氏管螺纹 平行内螺纹和锥形外螺纹 尺寸

This standard applies to assemblies of taper external threads on pipe couplings and screw plugs with type C stud ends as in DIN 3852-2 and type Z tapped holes with parallel internal thread as in DIN 3852-2. See DIN EN 10226-1 for Whitworth pipe threads for threaded pipes and fittings.

Whitworth pipe threads for pipe unions - Parallel internal thread and taper external thread - Dimensions

AIA/NAS NAS 1435-2005 FSC 1640.Rev. 3电缆孔眼及叉状端带终端

Terminal - Strap, Cable Eye End and Fork End Rev. 3; FSC 1640

Terminal - Strap, Cable Eye End and Fork End Rev. 3; FSC 1640

DIN 20401:2004 锯齿螺纹.0.8至2mm的螺距.尺寸

Threads according to this standard are intended for components, e. g. slit bolts according to DIN 22412. These threads are designed so that the axial forces effected by tightening the nut can be converted in radial forces only in minor parts.#,,#

Buttress threads - 0,8 mm to 2 mm pitch - Dimensions

NF E03-004-1*NF EN 10226-1:2004 用螺纹密封的管螺纹.第1部分:自攻外螺纹和平行内螺纹.尺寸、公差与标记

Pipe threads where pressure tight joints are made on the threads - Part 1 : taper external threads and parallel internal threads - Dimensions, tolerances and designation.

NF E03-057*NF ISO 965-5:2004 ISO通用米制螺纹.公差.第5部分:镀锌前与最大公差尺寸位置h热镀锌外螺纹相配的内螺纹的尺寸限值

ISO general purpose metric screw threads - Tolerances - Part 5 : limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing.

NF E03-049*NF ISO 724:2004 ISO一般用途米制螺纹.基本尺寸

ISO general-purpose metric screw threads - Basic dimensions.

NF E03-055:2004 ISO一般用途米制螺纹.公差.第4部分:热浸镀锌外螺纹的极限尺寸、与其相配的内螺纹镀锌后攻丝、内螺纹的公差带位置为H或G

ISO general purpose metric screw threads - Tolerances - Part 4 : limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing.

AIA/NAS NASM21083-2004 FSC 5310型250度F的低高度非金属插孔六边形自动锁螺母

DIMENSION ACROSS FLATS INCLUDE DEFORMATION OF SELF-LOCKING DEVICE.

Nut, Self-Locking, Hexagon, Non-Metallic Insert, Low Height, 250 Degrees F Rev 1

DIN 76-1:2004 符合DIN 13-1的ISO米制螺纹的螺纹尾部和螺纹切槽

This standard specifies thread run-outs and thread undercuts for screws and similar parts and for parts with internal thread with ISO metric threads in accordance with DIN 13-1 und DIN ISO 261 and the appropriate standard designations.

Thread run-outs and thread undercuts - Part 1: For ISO metric threads in accordance with DIN 13-1