L63 计算机外围设备 标准查询与下载

ISO 18926:2006 成像材料.磁光盘(MO)存储系统.基于温度和相对湿度效应的概率寿命的估算方法

This International Standard specifies a test method for estimating the life expectancy (LE) of information stored on rewritable and write-once magneto-optical media. Only the effects of temperature and relative humidity on the media are considered.

Imaging materials - Information stored on magneto-optical (MO) discs - Method for estimating the life expectancy based on the effects of temperature and relative humidity

DIN EN 62008:2006 数字数据采集系统及相关软件的性能特征和校准方法(IEC 62008:2005)

This standard ensures that all measurement systems that rely on DAQ devices meet a common standard.This standard covers: - The minimum specifications that the DAQ device manufacturer must provide to describe the performance of the analogue-to-digital module (ADM) of the DAQ device. - Standard test strategies to verify the minimum set of specifications. - The minimum calibration information, required by the ADM, that is stored on the DAQ device. - The minimum calibration software requirements for external and self-calibration of the ADM of the DAQ device.

Performance characteristics and calibration methods for digital data acquisition systems and relevant software (IEC 62008:2005); German version EN 62008:2005

GJB 5614-2006 军用超级计算机存储系统规范

本规范规定了军用超级计算机存储系统的技术要求、质量保证规定和交货运站准备要求等内容。 本规范适用于军用超级计算机存储系统的订购、设计、制造、检验、包装、运输、贮存和维修等。

Specification for memory system of military supercomputer

KS X 5623-2006 彩喷打印机和复合机中决定墨盒寿命的测试组件

? ??? ?? ??? ?? ?? ?? ??? ????? ??? ???? ????? ??

Standard color test suite for the determination of consumable yield for color electrophotographic/inkjet printers and multi-function devices thatcontain printer components

KS X 5620-2006 电子相片彩色打印机和复合机的色调墨盒寿命决定方式

? ??? ??? ?? ?? ?? ??? ????? ??? ???? ????[?? ??

Method for the determination of toner cartridge yield for color electrophotographic printers and multi-function devices that contain printer components

SJ 20937-2005 光盘机通用规范

本规范规定了光盘机的要求、质量保证规定、交货准备和说明事项等。 本规范适用于军用计算机光盘机的研制、生产、验收和采购。其它用于恶劣环境下进行数据记录的光盘机也可参照本规范。

General specification for optical disk driver

DLA SMD-5962-88519 REV A-2006 硅单片高电流驱动器线性微电路

This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A.

MICROCIRCUIT, LINEAR, HIGH CURRENT SOURCE DRIVERS, MONOLITHIC SILICON

ANSI/EIA 674-A:2006 小形态因数45毫米(1.8英寸)盘驱动器连接器位置和尺寸的规范

This specification defines the dimensions and connector locations of 45 millimeter (1.8 inch) small form factor disk drives.

Specification for Dimensions and Connector Locations of Small Form Factor 45 Millimeter (1.8 Inch) Disk Drive

ANSI/EIA 676-A:2006 平行1.8英尺驱动器波形因数的规范（78毫米×54毫米）

Defines the configuration characteristics associated with the 78 millimeter x 54 millimeter (1.8 inch) form factor drive that has a parallel interface and operates at 3.3V.

Specification for Parallel 1.8 Inch Drive Form Factor (78 millimeter x 54 millimeter)

ASTM F2555-06(2011) 喷墨打印机硒鼓页面利用率的测定标准规程-连续打印法

This practice can be used to determine the number of pages an ink jet printer cartridge can print until it reaches its end-of-life by continuously printing predetermined page area coverage. This practice can be used for the evaluation of an OEM (Original Equipment Manufacturer) cartridge compared to a refilled, remanufactured, or compatible ink jet printer cartridge when this practice is performed on the same printer. This practice is applicable to all ink jet cartridges, whether single or multi-color. This practice may be used for comparison between different ink jet printers that use the same cartridge(s) providing that print quality and media/paper settings are comparable. Comparable settings could typically be described as the printer’s default settings. This practice can be used to assess design goals of manufacturers of ink jet printer cartridges for ink capability, ink filling effectiveness, and the manufacturing process. This practice may be used for research and development, and for quality acceptance evaluation. The results produced by this practice can be used for competitive comparisons or the determination of cost per page analysis.1.1 This practice describes a continuous printing procedure to determine the page yield of an ink jet printer cartridge containing either a monochrome or a multi-color reservoir. Printing done continuously may result in a different page yield than that of intermittent printing. 1.2 This practice can be used to evaluate the page yield of an ink jet printer cartridge or a comparison between several ink jet printer cartridges when evaluated on the same ink jet printer model. This practice can also be used for a comparison between different printer models using the same cartridge number. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Determining Page Yield of Ink Jet Printer Cartridgesmdash;Continuous Printing Method

IEC 60950-1:2005 信息技术设备.安全.第1部分:一般要求

1.1.1 Equipment covered by this standard This standard is applicable to mains-powered or battery-powered information technology equipment, including electrical business equipment and associated equipment, with a RATED VOLTAGE not exceeding 600 V. This standard is also applicable to such information technology equipment: − designed for use as telecommunication terminal equipment and TELECOMMUNICATION NETWORK infrastructure equipment, regardless of the source of power; − designed and intended to be connected directly to, or used as infrastructure equipment in, a CABLE DISTRIBUTION SYSTEM, regardless of the source of power; − designed to use the AC MAINS SUPPLY as a communication transmission medium (see Clause 6, Note 4 and 7.1, Note 4). This standard is also applicable to components and subassemblies intended for incorporation in information technology equipment. It is not expected that such components and subassemblies comply with every aspect of the standard, provided that the complete information technology equipment, incorporating such components and subassemblies, does comply. This standard specifies requirements intended to reduce risks of fire, electric shock or injury for the OPERATOR and layman who may come into contact with the equipment and, where specifically stated, for a SERVICE PERSON. This standard is intended to reduce such risks with respect to installed equipment, whether it consists of a system of interconnected units or independent units, subject to installing, operating and maintaining the equipment in the manner prescribed by the manufacturer. This list is not intended to be comprehensive, and equipment that is not listed is not necessarily excluded from the Scope. Equipment complying with the relevant requirements in this standard is considered suitable for use with process control equipment, automatic test equipment and similar systems requiring information processing facilities. However, this standard does not include requirements for performance or functional characteristics of equipment. 1.1.2 Additional requirements Requirements additional to those specified in this standard may be necessary for: − equipment intended for operation in special environments (for example, extremes of temperature; excessive dust, moisture or vibration; flammable gases; and corrosive or explosive atmospheres); − electromedical applications with physical connections to the patient; − equipment intended to be used in vehicles, on board ships or aircraft, in tropical countries, or at altitudes greater than 2 000 m; − equipment intended for use where ingress of water is possible; for guidance on such requirements and on relevant testing, see Annex T. 1.1.3 Exclusions This standard does not apply to: − power supply systems which are not an integral part of the equipment, such as motorgenerator sets, battery backup systems and transformers; − building installation wiring; − devices requiring no electric power.

Information technology equipment - Safety - Part 1: General requirements

SAE AIR4013B-2005 MIL-STD-1760存储器用复接数据总线网络

This SAE Aerospace Information Report (AIR) will exame network aspects of open and shorted stubs, line reflections and bus loading due to network changes. Single network level is assumed, that is, no carriage store hierarchical levels. However, two passive network coupling variants called branched bus and branched stub will will be introduced that possibly could be used in a stores management netowrk. This report assumes familiarity with MIL-STD-1553B. This report assumes familiarity with MIL-STD-1553B. This document summarizes the results of hardware tests on simulated weapon data bus networks utilizing MIL-STD-1760. Unique to this application is the fact that the network is reconfigurable by connecting together mission dependent MIL-STD-1553B store remote terminals (RT)s at artificial network breakpoints. Further, during normal data bus operation the weapon RTs are physically removed from the network. That is, in-flight weapon separation from aircraft results in open stubs on the bus network. All this gives rise to changing network conditions, stubs exposed to harsh environments (such as during rocket motor firing), noise interference, interoperable store requirements for US/NATO military services and controversy about the effect of open stubs on bus performance.

Multiplex Data Bus Networks for Mil-Std-1760 Stores

IEC 60950-23:2005 IEC 60950-23, Ed. 1.0: 信息技术设备.安全.第23部分:大型数据存储设备

This part of IEC 60950 specifies requirements for information technology equipment (ITE) with self contained data storage systems that contain hazardous moving parts. These data storage systems are typically large enough to permit a person to enter completely, however, the systems also include similar large equipment permitting complete limb or head access to the area containing hazardous moving parts. These requirements are additional to the relevant requirements in IEC 60950-1. The maximum three dimensional reach of a cartridge accessory assembly typically has a minimum motion envelop of 0,75 m or more. The equipments shall be installed in a restricted access location, such as a data centre. The exceptions for 2.1.3 and 4.5.4 noted in 1.2.7.3 of IEC 60950-1 do not apply to this Part 23. NOTE 1 An example of equipment covered by this scope is an automated information mass storage and retrieval system that uses integral hazardous moving parts for the handling of recorded media (for example, tape cartridges, tape cassettes, optical disks, etc.) and similar functions. This standard is not applicable to equipment with non-self-contained hazardous moving parts, such as robotic equipment installed in an industrial environment. NOTE 2 For standards related to robotic equipment in an industrial environment, see IEC 60204-1, IEC 60204-11 and ISO 10218.

IEC 60950-23, Ed. 1.0: Information technology equipment - Safety - Part 23: Large data storage equipment

JIS X 6319-4:2005 集成电路卡用仪器规范.第4部分:高速临近卡

この規格は，高速化機能をもっ外部端子のない近接型ICカード(以下，カードという。)の物理特性，電波ィンタフェース，伝送プロトコル，ファイル構造，コマンドなどについて規定する。

Specification of implementation for integrated circuit(s) cards -- Part 4: High speed proximity cards

JIS X 6319-1:2005 集成电路卡用仪器规范.第1部分:带触点集成电路卡

この規格は，JIS X 6304及びJIS X 6306に適合している物理的特性をもったICカードの電気的特性，伝送制御手順などについて規定する。

Specification of implementation for integrated circuit(s) cards -- Part 1: Integrated circuit(s) cards with contacts

JIS X 6319-2:2005 集成电路卡用仪器规范.第2部分:临近卡

この規格は，近接型ICカード(以下，PICCという。)の物理特性(JIS X 6322-1), PICCとその結合装置(以下，PCDという。)との間の非接触通信に係る機能(JIS X 6322-2～-4)及び識別カードの試験方法(JIS X 6305-6)に加えて，これらを補足する事項について規定する。

Specification of implementation for integrated circuit(s) cards -- Part 2: Proximity cards

JIS X 6319-3:2005 集成电路卡用仪器规范.第3部分:交换的共同指令

この規格は，外部端子付きICカード及び近接型の外部端子なしICカードに対して適用するフアイル構造，セキュリティ構造，共通コマンドについて規定する。

Specification of implementation for integrated circuit(s) cards -- Part 3: Common commands for interchange

IEC 62142:2005 Verilog?寄存器传送级合成

This standard defines a set of modeling rules for writing Verilog HDL descriptions for synthesis. Adher-ence to these rules guarantees the interoperability of Verilog HDL descriptions between register-transfer level synthesis tools that comply to this standard. The standard defines how the semantics of Verilog HDL are used, for example, to describe level- and edge-sensitive logic. It also describes the syntax of the language with reference to what shall be supported and what shall not be supported for interoperability. Use of this standard will enhance the portability of Verilog-HDL-based designs across synthesis tools con-forming to this standard. In addition, it will minimize the potential for functional mismatch that may occur between the RTL model and the synthesized netlist.

Verilog? register transfer level synthesis

DLA A-A-55001 C VALID NOTICE 1-2005 小型计算机系统接口(SCSI)及其他配件, 只读光盘半高磁盘驱动器一般要求

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil

DISK DRIVE UNIT, HALF HEIGHT, CD-ROM, SMALL COMPUTER SYSTEM INTERFACE (SCSI), AND OTHER ACCESSORIES, GENERAL REQUIREMENTS FOR

NF C90-607-1:2005 多媒体系统与设备.色彩测量和管理.第7-1部分:彩色打印机.反射打印.RGB输入

Multimedia systems and equipment - Colour measurement and management - Part 7-1 : Colour printers - Reflective prints - RGB inputs.