L94 电子设备机械结构件 标准查询与下载

IEC 60297-3-107:2012 电子设备机械结构.482.6 mm(19 in)系列的机械结构尺寸规格.第3-107部分:小波形因数的插箱和插件尺寸

Scope and object This part of IEC 60297 defines the interface dimensions between subracks and associated plug-in units using connectors as defined in PICMG-MTCA.0 (Fixed board) and IEC 61076-4-116 (Two part) and other two part connectors. For mechanical and climatic tests refer to IEC 61587-1. For electromagnetic shielding performance tests refer to IEC 61587-3.

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-107: Dimensions of subracks and plug-in units, small form factor

BS EN 61587-2:2011 电子设备用机械结构.IEC 60917和IEC 60297试验.储藏柜和货架的地震试验

Mechanical structures for electronic equipment. Tests for IEC 60917 and IEC 60297. Seismic tests for cabinets and racks

IEC 61969-1:2011 电子设备的机械结构.户外机壳.第1部分:设计指南

This part of IEC 61969 contains design guidelines for outdoor enclosures and is applicable over a wide field of mechanical@ electromechanical and electronic equipment and its installation where a modular design is used. The objective of this standard is to provide an overview of specifications for enclosures focused on requirements for outdoor applications for stationary use at non-weather protected locations. These enclosures are considered to contain any equipment and provide protection for the outdoor installed facilities against unwanted environmental impacts. The installed equipment may be@ but is not limited to@ subracks according to IEC 60917-2-2 or IEC 60297-3-101.

Mechanical structures for electronic equipment - Outdoor enclosures - Part 1: Design guidelines

IEC 61969-3:2011 电子设备的机械结构.户外机壳.第3部分:环境要求,测试和安全性等

Mechanical structures for electronic equipment - Outdoor enclosures - Part 3: Environmental requirements, tests and safety aspects

IEC 61969-2:2011 电子设备的机械结构.户外机壳.第2部分:配合尺寸

This part of IEC 61969 applies to the design of enclosures for outdoor applications for stationary use at non-weatherprotected locations as defined in IEC 61969-1 Ed.2.0. The internal and external coordination dimensions are derived from IEC 60917-2. The internal dimensions meet the mounting dimensions of subracks in accordance with IEC 60917-2-2 and IEC 60297-3. The external dimensions@ compared to IEC 60917-2@ are partly increased in order to meet the design requirements of the outdoor specific conditions.

Mechanical structures for electronic equipment - Outdoor enclosures - Part 2: Coordination dimensions

BS DD IEC/TS 62610-2:2011 电子设备用机械结构.符合IEC 60297和IEC 60917系列要求的柜舱热管理.设计指南.强制风冷结构的测定方法

Mechanical structures for electronic equipment. Thermal management for cabinets in accordance with IEC 60297 and IEC 60917 series. Design guide. Method for the determination of forced air-cooling structure

IEC 61587-2:2011 IEC 61587-2,2.0版本:电子设备机械结构的IEC 60917和60297标准测试.第2部分:箱柜和支架的抗震测试

This part of IEC 61587 specifies seismic tests for cabinets and racks accommodated with IEC 60917 and 60297 series. It applies@ in whole or in part@ only to the mechanical structures of cabinets and racks for electronic equipment according to the above cited series of standards@ while it does not apply to the electronic equipment or systems deemed to be installed within these mechanical structures. This standard does not apply either to a cabinet or a rack having an anti-seismic isolation structure@ either external or internal. This standard aims to provide test conditions and criteria that constitute a reference to evaluate the ability of the mechanical structure of the cabinets or racks to acceptably withstand specified seismic intensities. For this purpose@ this standard specifies test specimen conditions@ such as dimensions (i.e. height@ width and depth) of the cabinet and the rack@ load distribution@ structural test condition and the RRS (required response spectra) of singleaxis or tri-axis acceleration as the seismic test wave condition. The single-axis or tri-axis acceleration is selectable.

IEC 61587-2, Ed. 2.0: Mechanical structures for electronic equipment - Tests for IEC 60917 and 60297 - Part 2: Seismic tests for cabinets and racks

IEC TS 62610-2:2011 电子设备的机械结构.符合IEC 60297和IEC 60917系列的机柜热管理.第2部分:设计指南:强制风冷结构的测定方法

Mechanical structures for electronic equipment - Thermal management for cabinets in accordance with IEC 60297 and IEC 60917 series - Part 2: Design guide: Method for determination of forced air-coolin

JIS C 6011-3:2011 JIS C 6010标准(所有部分)和IEC 60297标准(所有部分)用附件测试.第3部分:机箱,机框和机柜用电磁屏蔽性能测试

Tests for enclosures for JIS C 6010 (all parts) and IEC 60297 (all parts) -- Part 3: Electromagnetic shielding performance tests for cabinets, racks and subracks

JIS C 6011-1:2011 JIS C 6010标准(所有部分)和IEC 60297标准(所有部分)用附件测试.第1部分:机箱,机框,机柜和底架用安全性方面和气候,机械测试

Tests for enclosures for JIS C 6010 (all parts) and IEC 60297 (all parts) -- Part 1: Climatic, mechanical tests and safety aspects for cabinets, racks, subracks and chassis

JIS C 6011-2:2011 JIS C 6010标准(所有部分)和IEC 60297标准(所有部分)用附件测试.第2部分:机箱和机框用地震测试

Tests for enclosures for JIS C 6010 (all parts) and IEC 60297 (all parts) -- Part 2: Seismic tests for cabinets and racks

DIN EN 60297-3-106:2011 电子设备的机械结构.机械结构规格为482,6 mm(19 in)系列.第3-106部分:符合标准IEC 60917-2-1的米制机架或货架可用的支架或底架用适配尺寸

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-106: Adaptation dimensions for subracks and chassis applicable with metric cabinets or racks in accordance with IEC 60917-2-1 (IEC

DIN EN 60917-2-4:2011 电子设备机械结构开发用模块化规则.第2-4部分:分规范 -25 mm设备的接口协调尺寸.支架或底架用适配尺寸

Modular order for the development of mechanical structures for electronic equipment practices - Part 2-4: Sectional specification - Interface coordination dimensions for the 25 mm equipment practice - Adaptation dimensions for subracks or chassis applicab

NF C93-441-2-4*NF EN 60917-2-4:2010 电子设备构体的机械结构件研制用模块排序.第2-4部分:分规范.25 mm设备构体的接口协调尺寸规格.与IEC 60297-3-100标准符合的适用于机箱或机箱框的机框或机架用适应尺寸规格(19 in)

Modular order for the development of mechanical structures for electronic equipment practices - Part 2-4 : sectional specification - Interface coordination dimensions for the 25 mm equipment practice - Adaptation dimensions for subracks or chassis applica

NF C93-464-3-106*NF EN 60297-3-106:2010 电子设备用机械结构件.482.6 mm(19 in)系列机械结构件的尺寸规格.第3-106部分:符合IEC 60917-2-1标准的公制机柜或机箱框适用的机框和机架适应尺寸规格

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-106 : adaptation dimensions for subracks and chassis applicable with metric cabinets or racks in accordance with IEC 60917-2-1.

BS EN 60917-2-4:2010 电子设备机械结构开发用模型化规则.分规范.25mm设备的接口协调尺寸

This part of IEC 60917 specifies dimensions for mounting flanges of metric subracks or chassis that are to be mounted into 19 in cabinets or racks. Additional dimensions for subracks or chassis are according to the IEC 60917 series, and for 19 in cabinets or racks to the IEC 60297 series. EMC, seismic climatic and environmental requirements and tests, are defined in the IEC 61587 series. The drawings used in this standard are not intended to indicate product design, only the specific dimensions that shall be used. The terminology used complies with IEC 60917-1.

Modular order for the development of mechanical structures for electronic equipment practices - Sectional specification - Interface coordination dimensions for the 25 mm equipment practice - Adaptation dimensions for subracks or chassis applicable in cabi

BS EN 60297-3-106:2010 电子设备用机械结构.482.6 mm（19in）系列机械结构的尺寸电子设备的机械结构.符合标准IEC 60917-2-1的米制机架或货架可用的支架或底架的适配尺寸

This part of IEC 60297 specifies dimensions for mounting flanges of 19 in subracks or chassis that are to be mounted into metric cabinets or racks. Additional dimensions for subracks or chassis are according to the IEC 60297 series, and for metric cabinets or racks to the IEC 60917 series. EMC, seismic, climatic and environmental requirements and tests, are defined in the IEC 61587 series. The drawings used in this standard are not intended to indicate product design, only the specific dimensions that should be used. The terminology used complies with IEC 60917-1.

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Adaptation dimensions for subracks and chassis applicable with metric cabinets or racks in accordance with IEC 60917-2-1

BS EN 60191-6-18:2010 半导体设备的机械标准化.平面式安装半导体器件外壳外形图绘制的一般规则.球栅阵列(BGA)用设计指南

This part of IEC 60191 provides standard outline drawings, dimensions, and recommended variations for all square ball grid array packages (BGA), whose terminal pitch is 1 mm or larger.

Mechanical standardization of semiconductor devices. General rules for the preparation of outline drawings of surface mounted semiconductor device packages. Design guide for ball grid array (BGA)

IEC 60917-2-4:2010 电子设备用机械结构设计模块化规则.第2-4部分:分规范.25mm设备接口协调尺寸.与IEC 60297-3-100标准一致的机架或货架可用的支架或底架用适配尺寸(19英寸)

This part of IEC 60917 specifies dimensions for mounting flanges of metric subracks or chassis that are to be mounted into 19 in cabinets or racks. Additional dimensions for subracks or chassis are according to the IEC 60917 series, and for 19 in cabinets or racks to the IEC 60297 series. EMC, seismic climatic and environmental requirements and tests, are defined in the IEC 61587 series. The drawings used in this standard are not intended to indicate product design, only the specific dimensions that shall be used. The terminology used complies with IEC 60917-1

Modular order for the development of mechanical structures for electronic equipment practices - Part 2-4: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Adaptation dimensions for subracks or chassis applica

IEC 60297-3-106:2010 电子设备用机械构件.482,6mm(19英寸)系列机械构件的尺寸.第3-106部分:与IEC 60917-2-1标准一致的米制机架或货架可用的支架或底架用适配尺寸

This part of IEC 60297 specifies dimensions for mounting flanges of 19 in subracks or chassis that are to be mounted into metric cabinets or racks. Additional dimensions for subracks or chassis are according to the IEC 60297 series, and for metric cabinets or racks to the IEC 60917 series. EMC, seismic, climatic and environmental requirements and tests, are defined in the IEC 61587 series. The drawings used in this standard are not intended to indicate product design, only the specific dimensions that should be used. The terminology used complies with IEC 60917-1.

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-106: Adaptation dimensions for subracks and chassis applicable with metric cabinets or racks in accordance with IEC 60917-2-1