Q62 石膏制品 标准查询与下载

BS EN 13279-1:2005 石膏粘合剂和石膏灰泥.定义和要求

This European Standard specifies the characteristics and performance of powder products based on gypsum binder for building purposes. This includes premixed gypsum building plasters for plastering of walls and ceilings inside buildings where they are applied as a finishing material which can be decorated. These products are specially formulated to meet their application requirements by the use of additives/admixtures, aggregates and other binders. Gypsum and gypsum based building plasters for manual and mechanical applications are included. This European Standard also applies to gypsum binders both for direct use on site and for further processing into gypsum blocks, gypsum plasterboards, gypsum fibrous plasterwork and gypsum ceiling elements. Gypsum plaster for bricklaying is also included. Calcium sulfate used as binder for floor screeds is not covered by this standard. This European Standard defines the reference tests for technical characteristics and provides for the evaluation of conformity of the products covered by this European Standard. Building lime, as calcium hydroxide, can be used as an additional binder together with gypsum binder. If gypsum binder is the principle active binding component in a plaster then this plaster is covered by this standard. If building lime is the principle active binding component in a plaster then the plaster is covered by EN 998-1.

Gypsum binders and gypsum plasters - Definitions and requirements

NF P72-603:2005 石膏抹灰板用填缝材料.定义、要求和试验方法

Jointing materials for gypsum plasterboards - Definitions, requirements and test methods.

BS EN 14190:2005 再加工生成的石膏板产品.定义、要求和试验方法

This European Standard specifies the characteristics and performance of products which have been produced from gypsum plasterboards manufactured according to EN 520 by reprocessing. Reprocessing may include cutting, perforating, edge profiling, decorating and laminating membranes of other materials for functional or decorative purposes, attaching fixings including supports e.g. for partitions. A fuller list of reprocessing operations is given in Annex B. Gypsum plasterboards subject to reprocessing operations may be suitable for extended applications such as suspended ceilings providing sound absorption, flooring, self decorative finishes, low emissivity characteristics, moisture vapour control and X-ray protection. The products are intended for use in wall, ceiling and floor applications, where they may be fixed direct to the background, or they are used in systems assembled in conjunction with the structure to form separate or suspended linings. The products offer a wide range of aesthetic solutions of modular or non-modular design. This standard covers the following product performance characteristics: reaction to fire, water vapour permeability, stability in case of ceiling elements, flexural strength (breaking load), impact resistance, thermal resistance. The following performance characteristics are linked to systems assembled with products from reprocessing: shear strength, direct airborne sound insulation and acoustic absorption to be measured according to the corresponding European test methods. If required, tests should be done on assembled systems simulating the end use conditions. This European standard also covers additional technical characteristics that are of importance for the use and acceptance of the product by the construction industry and the reference tests for these characteristics. It provides for the evaluation of conformity of the product to this standard. This standard does not cover gypsum plasterboard thermal/acoustic insulation composite panels and prefabricated gypsum wallboard panels according to prEN 13950 and prEN 13915, respectively.

Gypsum plasterboard products from reprocessing - Definitions, requirements and test methods

SANS 622:2005 石膏凹圆檐板

Describes the requirements for gypsum cove cornice for use in buildings.

Gypsum cove cornice

NF P72-605:2005 石膏灰泥板系统用金属框架元件.定义、要求和试验方法

Metal framing components for gypsum plasterboard systems - Definitions, requirements and test methods.

DIN EN 14195:2005 石膏灰泥板系统用金属框架部件.定义、要求和试验方法

Metal framing components for gypsum plasterboard systems - Definitions, requirements and test methods; German version EN 14195:2005

NF P72-600:2005 石膏板.定义、要求和试验方法

Gypsum plasterboards - Definitions, requirements and tests methods.

BS EN 14195:2005 石膏灰泥板系统用金属框架元件.定义、要求和试验方法

This document specifies the characteristics of metal framing components intended to be used in building construction works in conjunction with gypsum plasterboard conforming to EN 520 and secondary processing conforming to EN 14190 where the assembly is non-loadbearing. These include, for example, partitions, wall and ceiling linings and the cladding of beams, columns, ducts and lift shafts. It covers the following performance characteristics: reaction to fire, flexural (yield) strength to be measured according to the corresponding European test methods. It defines the reference test methods for technical specifications. It provides for the evaluation of conformity of the product to this document. This EN also covers additional technical characteristics that are of importance for the use and acceptance of the product by the construction industry and the reference tests for these characteristics. A method of designation has been incorporated to cover the multiplicity of metal sections currently in use, without recourse to a means of rationalisation of their shape, profile or dimensions. This document does not cover load-bearing steel framing components and metal framing components for suspended ceilings according to EN 13964.

Metal framing components for gypsum plasterboard systems - Definitions, requirements and test methods

NF P72-400-2:2005 石膏粘结剂和石膏灰泥.第2部分:试验方法

Gypsum binders and gypsum plasters - Part 2 : test methods.

ASTM C1264-05 石膏板的抽样、检查、报废、认证、包装、标记、海运、搬运和储存的标准规范

1.1 This specification covers sampling; inspection; rejection; certification; packaging and marking; and shipping, handling, and storage of gypsum panel products.

Standard Specification for Sampling, Inspection, Rejection, Certification, Packaging, Marking, Shipping, Handling, and Storage of Gypsum Board

ASTM C473-05 石膏板制品的物理测试的标准试验方法

1.1 These test methods cover the physical testing of gypsum panel products.1.2 The test methods appear in the following order:SectionFlexural Strength (Method A)7Core, End and Edge Hardness (Method A)8Nail Pull Resistance (Method A)9Flexural Strength (Method B)11Core, End and Edge Hardness (Method B)12Nail Pull Resistance (Method B)13Humidified Deflection14End Squareness15Nominal Thickness16Recessed- or Tapered Edge Depth17Width18Length19Water Resistance of Core-Treated Water-Repellent Gypsum Panel Products20 Surface Water Resistance of Gypsum Panel Products with Water-Repellent Surfaces21 1.3 The text of these test methods references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of these test methods.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Physical Testing of Gypsum Panel Products

ASTM C1047-05 石膏墙板和石膏层板基底用附件的标准规范

1.1 This specification covers accessories used in conjunction with assemblies of gypsum wallboard and gypsum veneer plaster to protect edges and corners and to provide architectural features (see Fig. 1).1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are provided for information purposes only. The SI equivalents of inch-pound units may be approximate.

Standard Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base

ASTM C11-05 石膏及相关建筑材料和系统的标准术语

1.1 This standard covers terminology relating to gypsum and related building materials and systems. The terms are generically defined. More specific and expanded definitions may appear in appropriate standards.

Standard Terminology Relating to Gypsum and Related Building Materials and Systems

ASTM C842-05 室内石膏粉饰应用的标准规范

1.1 This specification covers the minimum requirements for full-thickness (in accordance with Table 1) interior gypsum plastering on gypsum, metal, masonry, or monolithic concrete bases designed or prepared to receive gypsum plaster. 1.1.1 Gypsum plaster applied to the interior side of exterior walls of masonry or concrete shall be isolated from the exterior wall.1.2 Gypsum plasters shall not be used in exterior locations or interior "wet" areas. Note 18212;To secure desirable results, this specification should be coordinated with the provisions of Specification C 841. General information concerning full thickness gypsum plastering is contained in Annex A2, Annex A3, and Annex A4.1.3 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories.1.4 Details of construction to achieve required sound control shall be obtained from reports of tests conducted at recognized sound testing laboratories in accordance with the applicable sound tests of Test Methods E 90, C 423, or E 492.1.5 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are approximate and are provided for information purposes only.1.6 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

Standard Specification for Application of Interior Gypsum Plaster

ASTM C842-05(2010)e1 室内石膏粉饰应用的标准规范

1.1 This specification covers the minimum requirements for full-thickness (in accordance with Table 1) interior gypsum plastering on gypsum, metal, masonry, or monolithic concrete bases designed or prepared to receive gypsum plaster. 1.1.1 Gypsum plaster applied to the interior side of exterior walls of masonry or concrete shall be isolated from the exterior wall. 1.2 Gypsum plasters shall not be used in exterior locations or interior “wet” areas. Note 18212;To secure desirable results, this specification should be coordinated with the provisions of Specification C841. General information concerning full thickness gypsum plastering is contained in Annex A2, Annex A3, and Annex A4. 1.3 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories. 1.4 Details of construction to achieve required sound control shall be obtained from reports of tests conducted at recognized sound testing laboratories in accordance with the applicable sound tests of Test Methods E90, C423, or E492. 1.5 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are approximate and are provided for information purposes only. 1.6 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

Standard Specification for Application of Interior Gypsum Plaster

ASTM C1264-05(2011) 石膏板的抽样,检查,报废,认证,包装,标记,海运,搬运和储存的标准规范

1.1 This specification covers sampling; inspection; rejection; certification; packaging and marking; and shipping, handling, and storage of gypsum panel products.

Standard Specification for Sampling, Inspection, Rejection, Certification, Packaging, Marking, Shipping, Handling, and Storage of Gypsum Board

BS EN 520:2004+A1:2009 石膏板.定义、要求和试验方法

This document specifies the characteristics and performance of gypsum plasterboards intended to be used in building construction works including those intended for secondary manufacturing operations. It includes boards designed to receive either direct surface decoration or gypsum plaster. This document covers the following product performance characteristics: reaction to fire, water vapour permeability, flexural strength (breaking load), impact resistance and thermal resistance. The following performance characteristics are linked to systems assembled with plasterboards: shear strength, fire resistance, impact resistance, direct airborne sound insulation and acoustic absorption to be measured according to the corresponding European test methods. If required, tests should be done on assembled systems simulating the end use conditions. This document covers also additional technical characteristics that are of importance for the use and acceptance of the product by the Construction Industry and the reference tests for these characteristics. It provides for the evaluation of conformity of the product to this document. This document does not cover plasterboards, which have been subject to any secondary manufacturing operations (e.g. insulating composite panels, plasterboards with thin lamination, etc.).

Gypsum plasterboards - Definitions, requirements and test methods

BS EN 520:2004 石膏板.定义、要求和试验方法

This document specifies the characteristics and performance of gypsum plasterboards intended to be used in building construction works including those intended for secondary manufacturing operations. It includes boards designed to receive either direct surface decoration or gypsum plaster. This document covers the following product performance characteristics: reaction to fire, water vapour permeability, flexural strength (breaking load), impact resistance and thermal resistance. The following performance characteristics are linked to systems assembled with plasterboards: shear strength, fire resistance, impact resistance direct airborne sound insulation and acoustic absorption to be measured according to the corresponding European test methods. If required, tests should be done on assembled systems simulating the end use conditions. This document covers also additional technical characteristics that are of importance for the use and acceptance of the product by the Construction Industry and the reference tests for these characteristics. It provides for the evaluation of conformity of the product to this document. This document does not cover plasterboards, which have been subject to any secondary manufacturing operations (e.g. insulating composite panels, plasterboards with thin lamination, etc.).

Gypsum plasterboards - Definitions, requirements and test methods

BS EN 13279-2:2004 石膏粘合剂和石膏灰泥.试验方法

This document describes the reference test methods for all gypsum binders and gypsum plasters covered by prEN 13279-1.

Gypsum binders and gypsum plasters - Test methods

GA 216-2004 研究组石膏制品的应用与整理

These are specifications for the application and finishing of gypsum panel products and related items and accessories to interior walls and ceilings and to exterior soffits.

APPLICATION AND FINISHING OF GYPSUM PANEL PRODUCTS