R00 标准化、质量管理 标准查询与下载

AASHTO TP 68-2004 电子外部接触器件地方热拌沥青密度(HMA)的标准试验方法

This method covers the in-place determination of the total density and relative compaction of HMA pavements by measuring changes in the electromagnetic field resulting from the compaction process.

Standard Method of Test for Density of In-Place Hot Mix Asphalt (HMA) Pavement by Electronic Surface Contact Devices

AASHTO MP 12-2004 可检测警告表面标准

Detectable warnings provide a distinctive surface of truncated domes detectable by cane or underfoot to alert people with vision impairments of the transition to vehicular ways. These warnings compensate for the sloped surfaces of curb ramps that remove

Standard Practice for Detectable Warning Surfaces

AASHTO T 325-2004 由三者测试在交通建设估算混凝土强度的标准试验方法

This standard provides procedures for estimating concrete strength in roads, bridges, and other transportation structures through the use of a maturity index.

Standard Method of Test for Estimating the Strength of Concrete in Transportation Construction by Maturity Tests

AASHTO T 317-2004 沥青铺装层温度方向的预测的标准试验方法

This test method provides a standard for measuring pavement surface temperature and predicting temperatures within the asphalt-bound layer(s) of a flexible pavement section. This test method provides a means of estimating the temperature at-depth from t

Standard Method of Test for Prediction of Asphalt-Bound Pavement Layer Temperatures

AASHTO GPRF-2-2004 泊车换车设施指南

AASHTO’s Technical Committee on Public Transportation Facilities Design is indebted to the many contributors to this guide. The foundational basis of the guide was the Park-and-Ride Planning and Design Guidelines, Monograph Il (October, 1997), developed

Guide for Park-and-Ride Facilities

AASHTO 511NPR-1-2003 511国家进度报告

511 National Progress Report

511 National Progress Report

AASHTO M 218-2003 波纹钢管用镀锌或钢板的标准规范

This specification covers steel sheet used in the manufacture of corrugated steel pipe (CSP) for storm sewers, culverts, drains, and similar uses. The sheet is zinc-coated (galvanized) by the hotdip process, and is produced in two coating weights, 610 g

Standard Specification for Steel Sheet, Zinc-Coated (Galvanized), for Corrugated Steel Pipe

AASHTO GDC-1-2003 可施工性设计指南-美国国家公路与运输协会/NSBA钢桥协作 G 12.1-2003

This document is a standard developed by the AASHTO/NSBA Steel Bridge Collaboration. The primary goal of the Collaboration is to achieve steel bridges of the highest quality and value through standardization of the design, fabrication, and erection proc

Guidelines for Design for Constructibility - AASHTO/NSBA Steel Bridge Collaboration G 12.1-2003

AASHTO DDPG-1-2003 设计图示指南

This guide is to advise the designer on items that are the minimum required in order to detail and fabricate a structure. The following information is not to be used

Design Drawing Presentation Guidelines

AASHTO T 168-2003 沥青铺面混合料取样的标准实施规程

All references to the ASTM standards listed in the following table, shall be replaced with the corresponding AASHTO standard

Standard Method of Test for Sampling Bituminous Paving Mixtures

AASHTO TP 64-2003 快速移动程序液压水泥混凝土氯离子渗透的预测的标准试验方法

This procedure is for the rapid evaluation of chloride penetration resistance of concrete, from nonsteady- state migration experiments.

Standard Method of Test for Predicting Chloride Penetration of Hydraulic Cement Concrete by the Rapid Migration Procedure

AASHTO T 249-2003 螺旋锁缝波纹管的标准测试方法

This method of test is to be followed in ascertaining the quality of the seam of a helical lock seam corrugated pipe.

Standard Method of Test for Helical Lock Seam Corrugated Pipe

AASHTO TP 65-2003 富锌引金属锌非仪器测定的标准试验方法

This test method determines the amount of metallic zinc in the dried paint film (nonvolatile matter) of inorganic zinc-rich and organic zinc-rich primers.

Standard Method of Test for Non-Instrumental Determination of Metallic Zinc in Zinc-Rich Primers

AASHTO T 323-2003 硅酸盐水泥混凝土在界面的粘结层的剪切强度的标准试验方法

This test method covers the determination of the interface shear strength of a drilled concrete core sampled from a bonded concrete overlay pavement or bridge deck.

Standard Method of Test for Determining the Shear Strength at the Interface of Bonded Layers of Portland Cement Concrete

JT/T 483-2002 交通科技报告编写规则

本标准规定了交通科技报告撰写的格式和要求。 本标准适用于承担交通科技项目的单位或个人撰写的交通科技报告。

Writing regulations for transportation science and technology reports

AASHTO HB-17 DIVISION II-2002 施工

Construction

Construction

AASHTO HB-17 DIVISION I-A-2002 抗振设计

Seismic Design

Seismic Design

AASHTO HB-17 DIVISION I-A SEC 4-2002 抗振设计-分析要求

The requirements of this section shall control the selection and method of seismic analysis of bridges. Four analysis procedures are presented.

Division I-A Seismic Design - Analysis Requirements

AASHTO HB-17 TOC-2002 公路桥的标准规范

Standard Specifications for Highway Bridges 17th Edition; Errata: 01/2003; Errata: 03/2005

Standard Specifications for Highway Bridges 17th Edition; Errata: 01/2003; Errata: 03/2005

AASHTO HB-17 DIVISION I-2002 设计

Design

Design