T13 进排气与燃油供给系统 标准查询与下载
共找到 596 条与 进排气与燃油供给系统 相关的标准，共 40 页
本标准规定了在用汽车改装为汽油/压缩天然气两用燃料汽车的改装技术要求。 本标准适用于天然气额定工作压力不大于20MPa的汽油/压缩天然气两用燃料汽车的改装。
The technical criterion of refitting for vehicle by using gas--Compressed natural gas for vehicle(CNGV)
- ICS
- 43.060.40
- CCS
- T13
- 发布
- 2001-09-03
- 实施
- 2002-04-01
本标准规定了汽车用液化石油气加气口的型式、技术要求、试验方法、检验规则、标志、包装、出厂文件、运输及贮存（定义见GB/T 17895）。 本标准适用于使用符合SY 7548要求的汽车用液化石油气为工作介质，公称工作压力为2.2MPa（本标准所述压力值均为表压），工作环境温度为-40～60℃的液化石油气汽车加气口。
Filling receptacle of LPG vehicle (spiral)
- ICS
- 43.060.40
- CCS
- T13
- 发布
- 2001-05-11
- 实施
- 2002-01-01
本标准规定了汽车用压缩天然气加气口的型式、技术要求、试验方法、检验规则、标志、包装、出厂文件、运输及贮存（定义见GB/T 17895）。 本标准适用于使用符合SY 7546要求的汽车用压缩天然气为工作介质，公称工作压力为20 M Pa（本标准所述压力值均为表压）的汽车用压缩天然气加气口。
Filling receptacle of CNG vehicle
- ICS
- 43.060.40
- CCS
- T13
- 发布
- 2001-05-11
- 实施
- 2002-01-01
本标准规定了以汽油、柴油为燃料的汽车燃油箱的安全性能要求和试验方法。 本标准适用于M类和N类汽车的金属燃油箱和塑料燃油箱。
Safety property requirements and test methods for automobile fuel tank
- ICS
- 43.060.40
- CCS
- T13
- 发布
- 2001-01-10
- 实施
- 2001-10-01
本标准规定了架装直列式喷油泵的尺寸要求。
Motor vehicles cradle-mounted in-line fuel injection pumps for diesel engimes--Mounting dimensions
- ICS
- 43.060
- CCS
- T13
- 发布
- 1996-10-17
- 实施
- 1999-04-01
本标准规定了载货汽车用空气滤清器滤芯尺寸规范。 本标准适用于载货汽车空气滤清器滤芯（以下简称滤芯）。
Dimensional specification for truck air filter elements
- ICS
- 43.060.20
- CCS
- T13
- 发布
- 1993-03-01
- 实施
- 1993-07-01
本标准规定了汽车空气滤清器的进口、出口、曲轴箱通风口、堵塞指示器接头等尺寸规范。 本标准适用于载货汽车空气滤清器。
Automobile air filter connector type A and type B
- ICS
- CCS
- T13
- 发布
- 1993-03-01
- 实施
- 1993-07-01
本标准规定了汽油车供油系抗气阻能力的道路试验方法。 本标准适用于装用汽油发动机的汽车。
Motor vehicles--Vapor lock for fuel system--Test method
- ICS
- 43.060.40
- CCS
- T13
- 发布
- 1991-03-22
- 实施
- 1991-12-01
本标准适用于汽车柴油机的燃油滤清器及燃油喷射装置试验设备的燃油滤清器。
Test values and classification of fuel filters for automotive compression ignition engines
- ICS
- 43.060.40
- CCS
- T13
- 发布
- 1986-03-05
- 实施
- 1986-12-01
本标准适用于汽车柴油机及燃油喷射装置试验设备的燃油滤清器。本标准规定的试验方法也可用 于燃用无残渣矿物油的柴油机燃油滤清器。 本标准适用于额定流量在200L/h以下的燃油滤清器。
Test methods of fuel filters for automotive compression ignition engines
- ICS
- 43.060.40
- CCS
- T13
- 发布
- 1986-03-05
- 实施
- 1986-12-01
Reductant filter for automotive diesel selective catalytic reduction (SCR) system
- ICS
- 43.060.20
- CCS
- T13
- 发布
- 2022-04-24
- 实施
- 2022-10-01
Natural gas filter for automobiles
- ICS
- 43.060.40
- CCS
- T13
- 发布
- 2022-04-24
- 实施
- 2022-10-01
Air filter for carbon canister for gasoline passenger cars
- ICS
- 43.060.40
- CCS
- T13
- 发布
- 2022-04-24
- 实施
- 2022-10-01
This document specifies dimensional requirements for 10 types of end-mounting flanges of highpressure supply pumps for common rail fuel injection systems for use in diesel (compression-ignition) engines.
Diesel engines - End-mounting flanges for pumps - Part 2: High-pressure supply pumps for common rail fuel injection systems
- ICS
- 43.060.40
- CCS
- T13
- 发布
- 2021-08-00
- 实施
Road vehicles. Liquefied natural gas (LNG) fuel system components. Manual valve
- ICS
- 43.060.40
- CCS
- T13
- 发布
- 2021-06-11
- 实施
- 2021-06-11
This document specifies tests and requirements for the rigid fuel line in copper and its alloys, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is not applicable to the following: a) fuel containers; c) container mounting hardware; e) refuelling receptacles. b) stationary gas engines; d) electronic fuel management; It is recognized that miscellaneous components not specifically covered herein can be examined to meet the criteria of this document and tested according to the appropriate functional tests. All references to pressure in this document are to be considered gauge pressures unless otherwise specified. This document is based upon a working pressure for natural gas as a fuel of 1,6 MPa (16 bar1)). Other working pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio). For example, a 2 MPa (20 bar) working pressure system will require pressures to be multiplied by 1,25.
Road vehicles - Liquefied natural gas (LNG) fuel system components - Part 12: Rigid fuel line in copper and its alloys
- ICS
- 43.060.40
- CCS
- T13
- 发布
- 2021-06-00
- 实施
This document specifies tests and requirements for the tank pressure control regulator, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically covered herein can be examined to meet the criteria of this document and tested according to the appropriate functional tests. All references to pressure in this document are to be considered gauge pressures unless otherwise specified. This document is based upon a working pressure for natural gas as a fuel of 1,6 MPa [16 bar1)]. Other working pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio). For example, 2 MPa (20 bar) working pressure system will require pressures to be multiplied by 1,25.
Road vehicles - Liquefied natural gas (LNG) fuel system components - Part 13: Tank pressure control regulator
- ICS
- 43.060.40
- CCS
- T13
- 发布
- 2021-06-00
- 实施
This document specifies tests and requirements for the heat exchanger-vaporizer, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is not applicable to the following: a) fuel containers; c) container mounting hardware; e) refuelling receptacles. b) stationary gas engines; d) electronic fuel management; It is recognized that miscellaneous components not specifically covered herein can be examined to meet the criteria of this document and tested according to the appropriate functional tests. All references to pressure in this document are to be considered gauge pressures unless otherwise specified. This document is based upon a working pressure for natural gas as a fuel of 1,6 MPa (16 bar1)). Other working pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio). For example, a 2 MPa (20 bar) working pressure system will require pressures to be multiplied by 1,25.
Road vehicles - Liquefied natural gas (LNG) fuel system components - Part 16: Heat exchanger-vaporizer
- ICS
- 43.060.40
- CCS
- T13
- 发布
- 2021-06-00
- 实施
This document specifies tests and requirements for the excess flow valve, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles using natural gas in accordance with ISO 15403-1 (mono-fuel, bi-fuel, or dualfuel applications). It is not applicable to the following: a) fuel containers; c) container mounting hardware; e) refuelling receptacles. b) stationary gas engines; d) electronic fuel management; It is recognized that miscellaneous components not specifically covered herein can be examined to meet the criteria of this document and tested according to the appropriate functional tests. All references to pressure in this document are to be considered gauge pressures unless otherwise specified. This document is based upon a working pressure for natural gas as a fuel of 1,6 MPa (16 bar1)). Other working pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio). For example, a 2 MPa (20 bar) working pressure system will require pressures to be multiplied by 1,25.
Road vehicles - Liquefied natural gas (LNG) fuel system components - Part 8: Excess flow valve
- ICS
- 43.060.40
- CCS
- T13
- 发布
- 2021-06-00
- 实施
This document specifies tests and requirements for the differential pressure fuel content gauge, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in a) fuel containers; c) container mounting hardware; e) refuelling receptacles. b) stationary gas engines; d) electronic fuel management; It is recognized that miscellaneous components not specifically covered herein can be examined to meet the criteria of this document and tested according to the appropriate functional tests. All references to pressure in this document are to be considered gauge pressures unless otherwise specified. This document is based upon a maximum working pressure for natural gas as fuel of 1,6 MPa (16 bar1)). Other working pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio). For example, a 2 MPa (20 bar) working pressure system will require pressures to be multiplied by 1,25.
Road vehicles - Liquefied natural gas (LNG) fuel system components - Part 14: Differential pressure fuel content gauge
- ICS
- 43.060.40
- CCS
- T13
- 发布
- 2021-06-00
- 实施
