T13 进排气与燃油供给系统 标准查询与下载

ISO 12614-12:2021 道路车辆. 液化天然气(LNG)燃料系统部件. 第12部分: 铜及其合金硬质燃料管线

This document specifies tests and requirements for the rigid fuel line in copper and its alloys, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is not applicable to the following: a) fuel containers; c) container mounting hardware; e) refuelling receptacles. b) stationary gas engines; d) electronic fuel management; It is recognized that miscellaneous components not specifically covered herein can be examined to meet the criteria of this document and tested according to the appropriate functional tests. All references to pressure in this document are to be considered gauge pressures unless otherwise specified. This document is based upon a working pressure for natural gas as a fuel of 1,6 MPa (16 bar1)). Other working pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio). For example, a 2 MPa (20 bar) working pressure system will require pressures to be multiplied by 1,25.

Road vehicles - Liquefied natural gas (LNG) fuel system components - Part 12: Rigid fuel line in copper and its alloys

ISO 12614-7:2021 道路车辆. 液化天然气(LNG)燃料系统部件. 第7部分: 泄压阀

This document specifies tests and requirements for the pressure relief valve (PRV), a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is not applicable to the following: a) fuel containers; c) container mounting hardware; e) refuelling receptacles. b) stationary gas engines; d) electronic fuel management; It is recognized that miscellaneous components not specifically covered herein can be examined to meet the criteria of this document and tested according to the appropriate functional tests. All references to pressure in this document are to be considered gauge pressures unless otherwise specified. This document is based upon a working pressure for natural gas as a fuel of 1,6 MPa [16 bar1)]. Other working pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio). For example, 2 MPa (20 bar) working pressure system will require pressures to be multiplied by 1,25.

Road vehicles - Liquefied natural gas (LNG) fuel system components - Part 7: Pressure relief valve (PRV)

ISO 12614-14:2021 道路车辆. 液化天然气(LNG)燃料系统部件. 第14部分: 压差燃料含量测量仪

This document specifies tests and requirements for the differential pressure fuel content gauge, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in a) fuel containers; c) container mounting hardware; e) refuelling receptacles. b) stationary gas engines; d) electronic fuel management; It is recognized that miscellaneous components not specifically covered herein can be examined to meet the criteria of this document and tested according to the appropriate functional tests. All references to pressure in this document are to be considered gauge pressures unless otherwise specified. This document is based upon a maximum working pressure for natural gas as fuel of 1,6 MPa (16 bar1)). Other working pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio). For example, a 2 MPa (20 bar) working pressure system will require pressures to be multiplied by 1,25.

Road vehicles - Liquefied natural gas (LNG) fuel system components - Part 14: Differential pressure fuel content gauge

ISO 12614-3:2021 道路车辆. 液化天然气(LNG)燃料系统部件. 第3部分: 止回阀

This document specifies tests and requirements for the check valve, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is not applicable to the following: a) fuel containers; c) container mounting hardware; e) refuelling receptacles. b) stationary gas engines; d) electronic fuel management; It is recognized that miscellaneous components not specifically covered herein can be examined to meet the criteria of this document and tested according to the appropriate functional tests. All references to pressure in this document are to be considered gauge pressures unless otherwise specified. This document is based upon a working pressure for natural gas as a fuel of 1,6 MPa [16 bar1)]. Other working pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio). For example, 2 MPa (20 bar) working pressure system will require pressures to be multiplied by 1,25.

Road vehicles - Liquefied natural gas (LNG) fuel system components - Part 3: Check valve

ISO 12614-5:2021 道路车辆. 液化天然气(LNG)燃料系统部件. 第5部分: 罐压计

This document specifies tests and requirements for the tank pressure gauge, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is not applicable to the following: a) fuel containers; c) container mounting hardware; e) refuelling receptacles. b) stationary gas engines; d) electronic fuel management; It is recognized that miscellaneous components not specifically covered herein can be examined to meet the criteria of this document and tested according to the appropriate functional tests. All references to pressure in this document are to be considered gauge pressures unless otherwise specified. This document is based upon a working pressure for natural gas as a fuel of 1,6 MPa [16 bar1)]. Other working pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio). For example, 2 MPa (20 bar) working pressure system will require pressures to be multiplied by 1,25.

Road vehicles - Liquefied natural gas (LNG) fuel system components - Part 5: Tank pressure gauge

ISO 12614-17:2021 道路车辆. 液化天然气(LNG)燃料系统部件. 第17部分: 天然气探测器

This document specifies tests and requirements for the natural gas detector, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically covered herein can be examined to meet the criteria of this document and tested according to the appropriate functional tests. All references to pressure in this document are to be considered gauge pressures unless otherwise specified. This document is based upon a working pressure for natural gas as a fuel of 1,6 MPa [16 bar1)]. Other working pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio). For example, 2 MPa (20 bar) working pressure system will require pressures to be multiplied by 1,25.

Road vehicles - Liquefied natural gas (LNG) fuel system components - Part 17: Natural gas detector

ISO 17536-1:2015/Amd 1:2021 道路车辆. 内燃机气溶胶分离器性能试验. 第1部分: 总则. 修改件1

Road vehicles - Aerosol separator performance test for internal combustion engines - Part 1: General; Amendment 1

BS ISO 15500-5:2020 道路车辆. 压缩天然气(CNG)燃料系统部件. 手控气缸阀

Road vehicles. Compressed natural gas (CNG) fuel system components. Manual cylinder valve

BS ISO 15500-4:2020 道路车辆. 压缩天然气(CNG)燃料系统部件. 手控阀

Road vehicles. Compressed natural gas (CNG) fuel system components. Manual valve

ISO 15500-4:2020 道路车辆. 压缩天然气(CNG)燃料系统部件. 第4部分: 控阀

This document specifies tests and requirements for the manual valve, a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with ISO 15403-1. It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer; b) fuel containers; c) stationary gas engines; d) container-mounting hardware; e) electronic fuel management; f) refuelling receptacles.

Road vehicles - Compressed natural gas (CNG) fuel system components - Part 4: Manual valve

ISO 15500-5:2020 道路车辆. 压缩天然气(CNG)燃料系统部件. 第5部分: 手控气缸阀

This document specifies tests and requirements for the manual cylinder valve, a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with ISO 15403-1. It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer; c) stationary gas engines; e) electronic fuel management; b) fuel containers; d) container-mounting hardware; f) refuelling receptacles.

Road vehicles - Compressed natural gas (CNG) fuel system components - Part 5: Manual cylinder valve

QC/T 1133-2020 商用汽车空气滤清器安全滤芯

Commercial vehicle air filter safety filter element

QC/T 1134-2020 发动机进气水分离试验方法

Engine air intake water separation test method

QC/T 770-2020 汽车用干式空气滤清器总成

Automotive dry air filter assembly

QC/T 793-2020 摩托车和轻便摩托车空气滤清器

Motorcycle and moped air filters

DB4403/T 1-2018 在用柴油车污染控制装置符合性查验规范

本标准适用于在用柴油车的环保定期检验、现场检查、抽样抽测等环节。

Specifications for compliance inspection of pollution control devices for in-use diesel vehicles

ISO 16332:2018 柴油机.柴油滤清器.燃料/水分离效果评定方法

This document specifies a fuel/water separator comparison test under defined and simplified laboratory conditions. This test is intended for pressure side fuel/water separators as well as for suction side fuel/water separators. Pressure side fuel/water separators are tested with fine droplets and suction side filters are tested with coarse droplets using the same test rig layout. The rated flow (in litres per hour) is intended for the range between 50 l/h and 1500 l/h. By agreement between customer and fuel/water separator manufacturer, and with some modifications, the procedures can be used for fuel/water separators with higher or lower flow rates.

Diesel engines - Fuel filters - Method for evaluating fuel/water separation efficiency

ISO 2974:2018 柴油发动机. 高压燃料喷射组件的60°内锥

This document specifies the dimensional requirements of end-connections for high-pressure fuel injection equipment components, used on diesel (compression-ignition) engines. It is applicable to externally threaded 60° female cones (see Figures 1, 2, 5, and 6) and intended for use with high-pressure fuel injection pipe assemblies with tube outside diameters of: — up to and including 12 mm for integral female cones (see Table 1); and — up to and including 9 mm for fabricated female cones (see Table 2). Details of the pipe connection ends referenced in this document are shown in ISO 13296.

Diesel engines - 60° female cones for high-pressure fuel injection components

ISO 12251:2017 柴油发动机.夹具安装的燃油喷射器.安装尺寸规格

This document specifies dimensional requirements for clamp mounted CR fuel injectors and their corresponding cylinder head features in diesel engines. According to the injector nozzle capnut, the clamp mounted CR fuel injectors can be divided into two types: a) Type A, where the nozzle capnut is straight (see Figure 4); b) Type B, where the nozzle capnut is stepped (see Figure 5). Each clamp mounted CR fuel injector type is subdivided by a series of different sizes. NOTE This differentiation corresponds to the relationship between the two guide diameters of the clamp mounted CR fuel injectors.

Diesel engines - Clamp mounted CR fuel injectors - Mounting dimensions

DIN EN ISO 12617:2017 道路车辆.液化天然气(LNG)再加连接器.3,1MPa连接器(ISO 12617-2015,修正版本2016-01-15);德文版本EN ISO 12617-2017

DIN EN ISO 12617 specifies liquefied natural gas (LNG) refuelling nozzles and receptacles for road vehicles powered by LNG.

Road vehicles - Liquefied natural gas (LNG) refuelling connector - 3,1 MPa connector (ISO 12617:2015, Corrected version 2016-01-15); German version EN ISO 12617:2017