Y76 服装、服饰品 标准查询与下载

DB32/T 2074-2012 学生军训服

student military uniform

ASTM D7268-12 包括密集织物和游泳衣的集密编织服饰的标准性能规范

Upon mutual agreement between the purchaser and the supplier, seamless knit garments intended for this end use should meet all of the requirements listed in Table 1 of this specification. It is recognized that, for purposes of fashion or aesthetics, the ultimate consumer of articles made from these fabrics may find acceptable products that do not conform to all of the requirements listed in Table 1. Therefore, one or more of the requirements in Table 1 may be modified by mutual agreement between the purchaser and the supplier. In such cases, any references to the specifications should specify that: “This product meets ASTM specifications XXXX except for the following characteristic(s).” Where no pre-purchase agreement has been reached between the purchaser and supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 4.2, ultimate consumer demands dictate varying performance parameters for a particular product. The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods. TABLE 1 Specification Requirements CharacteristicRequirements Section Bursting Strength<5 oz30 lb/sq in Colorfastness LaunderingColor Change4.0 Min7.2 Staining3.0 Min DrycleaningColor change4.0 Min7.3 Staining3.0 Min CrockingDry4.0 Min7.4 Wet3.0 Min Light Swimwear 40 AFU'sGrade 3.5 Min7.5 Intimates 20 AFU'sGrade 3.5 Min PerspirationColor change4.5 Min7.6 Staining3.5 Min Water Color change4.5 Min7.7 Staining3.5 Min Sea Water ...........

Standard Performance Specification for Seamless Knit Garments Including Intimates and Swimwear

ASTM F1930-12 使用仪器化假人进行耐火服装抗火灾性能模拟评估的标准试验方法

Use this test method to measure the thermal protection provided by different materials, garments, clothing ensembles, and systems to a specified fire exposure (see 3.2.2, 4.1, 10.1.3, and 10.1.4). This test method does not simulate high radiant exposures, for example, those found in electric arc flash exposures, some types of fire exposures where liquid or solid fuels are involved, nor exposure to nuclear explosions. This test method provides a measurement of garment and clothing ensemble performance on a stationary upright manikin of specified dimensions. This test method is used to provide predicted skin burn injury for a specific garment or protective clothing ensemble when exposed to a laboratory simulation of a fire. It does not establish a pass/fail for material performance. This test method is not intended to be a quality assurance test. The results do not constitute a material’s performance specification. The effects of body position and movement are not addressed in this test method. The measurement of the thermal protection provided by clothing is complex and dependent on the apparatus and techniques used. It is not practical in a test method of this scope to establish details sufficient to cover all contingencies. Departures from the instructions in this test method have the potential to lead to significantly different test results. Technical knowledge concerning the theory of heat transfer and testing practices is needed to evaluate if, and which departures from the instructions given in this test method are significant. Standardization of the test method reduces, but does not eliminate, the need for such technical knowledge. Report any departures along with the results.1.1 This test method is used to provide predicted human skin burn injury for single layer garments or protective clothing ensembles mounted on a stationary instrumented manikin which are then exposed in a laboratory to a simulated fire environment having controlled heat flux, flame distribution, and duration. The average exposure heat flux is 84 kW/m2 (2 cal/s•cm2), with durations up to 20 seconds. 1.2 The visual and physical changes to the single layer garment or protective clothing ensemble are recorded to aid in understanding the overall performance of the garment or protective ensemble and how the predicted human skin burn injury results can be interpreted. 1.3 The skin burn injury prediction is based on a limited number of experiments where the forearms of human subjects were exposed to elevated thermal conditions. This forearm information for skin burn injury is applied uniformly to the entire body except for the hands and feet. The hands and feet are not included in the skin burn injury prediction. 1.4 The measurements obtained and observations noted can only apply to the particular garment(s) or ensemble(s) tested using the specified heat flux, flame distribution, and duration. 1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.6 This method is not a fire-test-response test method. 1.7 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units or other units commonly used for thermal testing. If appropriate, round the non-SI units for convenience. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of ......

Standard Test Method for Evaluation of Flame Resistant Clothing for Protection Against Fire Simulations Using an Instrumented Manikin

ASTM F1958/F1958M-12 用人体模型的电弧暴露法测定服装非耐火材料易燃性的标准试验方法

1.1 Material performance shall be determined from the ignitability of the specimen(s) and shall be reported as a probability of ignition at various incident energy levels. 5.1.2 Materials which meet the flame resistance requirements of Specification F1506 do not require testing by this test method unless the mechanism of passing Specification F1506 involves melting and escape from the flame source (for example, coated fabrics, certain rainwear fabrics). 5.2 This test method maintains the specimen in a static, vertical position and does not involve movement except that resulting from the exposure. 5.3 This test method specifies a standard set of exposure conditions. Different exposure conditions may produce different results. In addition to the standard set of exposure conditions, other conditions representative of the expected hazard may be used. 1.1 This test method is used to identify materials that are ignitable and that can continue to burn when exposed to an electric arc, and determines (a) the incident exposure energy that causes ignition, and (b) the probability of ignition. 1.2 The specimens tested in this test method are materials fabricated in the form of shirts. 1.3 This test method shall be used to measure and describe the properties of materials, products, or assemblies in response to convective and radiant energy generated by an electric arc under controlled laboratory conditions. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard shall not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and hea......

Standard Test Method for Determining the Ignitability of Non-flame-Resistant Materials for Clothing by Electric Arc Exposure Method Using Mannequins

FZ/T 81008-2011 茄克衫

本标准规定了茄克衫的要求、检测方法，检验规则，以及标志、包装、运输和贮存等技术特征。 本标准适用于以纺织机织物为主要面料生产的茄克衫。 本标准不适用于儿童服装及婴幼儿服装。

Jackets

ASTM D2050-11 相关组件的标准术语

1.1 This terminology document covers terminology pertaining to items that are considered fasteners and closures such as buttons, hook and loop touch fasteners, snap fasteners and slide fasteners used in the manufacture of textile products, except for seams and stitches. 1.2 Section 3, Terminology, is categorized into four subsections, specific to the four areas of specialization under this document: 1.2.1 Relating to Buttons 1.2.2 Relating Hook and Loop Touch Fasteners 1.2.3 Relating to Snap Fasteners 1.2.4 Relating to Slide Fasteners 1.3 Terminology relating specifically to buttons covers special terms or special meanings used in the button industry. These apply only to sew-through flange and shank buttons. 1.3.1 The principal types of buttons defined in this terminology document are illustrated in Figs. 1-8. 1.3.2 These figures are descriptive only and are not intended to be restrictive as to design. 1.4 Terminology relating specifically to snap fasteners includes illustration of prong-ring attached fastener parts in Fig. 9. 1.4.1 These figures are descriptive only and are not intended to be restrictive as to design. 1.5 Terminology relating specifically to the principle parts of slide fasteners defined in this terminology are illustrated in Figs. 10-19. 1.5.1 These figures are descriptive only and are not intended to be restrictive as to design. 1.6 Terminology relating specifically to the textile joining structures (seams and stitches) are discussed in detail in Terminology D5646. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Terminology Relating to Fasteners and Closures Used with Textiles

DB41/T 657-2010 医务人员职业服装

Professional clothing for medical staff

KS K ISO 15831:2010 服装.生理效应.用热的人体模型测量热绝缘性

이 표준은 서멀마네킹의 요구 표준과 의복 한 세트의 단열성을 측정하는 방법에 대하여 규정한

Clothing-Physiological effects-Measurement of thermal insulation by means of a thermal manikin

DB44/T 825-2010 棉横编针织品

本标准规定了棉横编针织品的术语和定义、产品分类、要求、试验方法、检验规则以及标志、包装、运输、贮存。 本标准适用于鉴定棉横编针织品的品质。

Cotton Flat Knit

DB41/T 634-2010 可拆洗弹力羽绒裤

Removable and washable stretch down pants

SN/T 0682-2010 进出口头巾、围巾检验规程

本标准规定了进出口头巾、围巾的抽样、检验和检验结果的判定。 本标准适用于以各类纺织纤维制成的进出口头巾和围巾的检验。

Rules of inspection on import and export scarfs

SN/T 2517-2010 进境羽毛羽绒检疫操作规程

本标准规定了进境羽毛羽绒的检疫抽样、检疫查验内容和要求、检疫查验方法和程序、结果判定规则及处理措施等。 本标准适用于进境羽毛羽绒的检疫。

Protocal of quarantine for import feather and down

MZ/T 014.3-2010 救灾被服 第3部分：棉衣

本部分规定了救灾专用棉衣的要求、试验方法、检验规则及标志、包装、运输与贮存。 本部分适用于救灾专用棉衣的订购、生产与验收。

Disaster relief bedding and clothing.Part 3:Warmth cloths

MZ/T 014.2-2010 救灾被服 第2部分：棉大衣

本部分规定了救灾专用棉大衣的要求、试验方法、检验规则及标志、包装、运输与贮存。 本部分适用于救灾专用棉大衣的订购、生产与验收。

Disaster relief bedding and clothing.Part 2:Overcoat

FZ/T 81010-2009 风衣

本标准规定了风衣产品的要求、检验(测试)方法、检验规则和标志、包装、运输、贮存等。 本标准适用于以纺织机织物为主要面料生产的风衣。

Trench coats

ASTM D2050-09 相关组件的标准术语

1.1 This terminology covers all terminology pertaining to items that are considered subassemblies in the manufacture of textile products except seams and stitches. Textile joining structures (seams and stitches) are discussed in detail in Practice D 6193 1.2 The principle parts of slide fastners defined in this terminology are illustrated in Figs. 1-10. These figures are descriptive only and are not intended to be restrictive as to design. FIG. 1 Bottom Stop FIG. 2 Bridge Stop FIG. 3 Top Stop FIG. 4 Principle Parts of Slide Fasteners—Continuous Element Slide FastenerFIG. 5 Element (one side of element on sewn type CE fastener) FIG. 6 Principal Parts of Slide Fasteners—Individual Element Slide Fasteners FIG. 7 Movable Retainer FIG. 8 Releasing Stops FIG. 9 Separating Parts FIG. 10 Sliders

Standard Terminology Relating to Subassemblies

ASTM D7506/D7506M-09 口袋加固的标准测试方法

1.1 This test method utilizes the grab procedures to determine localized weakness due to bar-tacking in the pocket areas of all types of garments. This can be utilized to test bar-tacking in the pockets of shirts, as well as side or back pockets of trousers, pants, or jeans. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Pocket Reinforcement

ASTM F2727-09 标识头饰产品的制造商的标准指南

This guide gives guidelines for labels and instructions to manufacturers of non-motorized sports and recreation headgear. The purpose of the labels and instructions is to help alert and remind headgear users of important issues related to headgear and its use. Limitation8212;This guide applies only to protective headgear whose standard specifications are under auspices of ASTM Committee F08.1.1 This guide sets forth labeling and instruction guidelines for manufacturers of headgear for non-motorized sports and recreation. 1.2 This guide applies only to protective headgear whose standard specifications are under auspices of ASTM Committee F08. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Manufacturers for Labeling Headgear Products

ASTM D5171-09a 塑料线缝纽扣的耐撞击性标准试验方法

This test method may be used to determine the ability of a button to resist breaking under impact, for example in pressing the end item, which could cause the button to fail. Note 18212;In the development of this test method it was found that the following factors influenced the ability of a button to resist failure under impact conditions: resin formulation, shape ligne size, thickness, number and spacing of holes. Buttons may also pass this test but fail during the pressing of a garment due to the presence of heat during pressing. If there are differences of practical significance between the reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate rest results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. Test Method D 5171 for the determination of the impact resistance of buttons may be used for acceptance testing of commercial shipments of buttons but caution is advisable since information is lacking on precision.1.1 This test method covers the determination of impact resistance of plastic sew-through buttons. 1.2 The values stated in either acceptable metric units or other units shall be regarded separately as standard. The values expressed in each system may or may not be exact equivalents: therefore, each system must be used independently of the other, without combining values in any way. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Impact Resistance of Plastic Sew-Through Buttons

SANS 1382-1:2008 长筒袜.第1部分:机构用男式和女式长统袜

Covers the requirements for fourteen types of men's quarter, half and three-quarter hose and four types of women's anklet and three-quarter hose.

Hose Part 1: Men's and women's hose for institutional use