Y76 服装、服饰品 标准查询与下载

DIN EN 14682:2015 童装安全.童装上的饰带和下摆束带.规范;德文版本EN 14682-2014

Safety of children's clothing - Cords and drawstrings on children's clothing - Specifications; German version EN 14682:2014

NF G30-105*NF EN 14682:2015 童装安全.童装上的绳索和下摆束带.规范

La présente Norme européenne fixe des exigences concernant les cordons, coulissants ou non, de vêtements d'enfants, y compris les costumes de déguisement et les combinaisons de ski, jusqu'à l'âge de 14 ans.

Safety of children's clothing - Cords and drawstrings on children's clothing - Specifications

GOST 30332-2015 羽毛和羽绒消费品. 规格

Feather and down consumer goods. Specifications

BS PD CEN/TR 16792:2014 儿童服装安全. 儿童服装的设计和生产建议. 机械安全

Safety of children's clothing. Recommendations for the design and manufacture of children's clothing. Mechanical safety

BS EN 14682:2014 童装安全.童装上的饰带和下摆束带.规范

Safety of children's clothing. Cords and drawstrings on children's clothing. Specifications

DB43/T 976-2014 阻燃茄克衫

flame retardant jacket

DB43/T 973-2014 防静电茄克衫

Anti-static jacket

FZ/T 81020-2014 机织文胸

本标准规定了机织文胸的要求、检测方法、检验分类规则,以及标志、包装、运输和贮存等全部技术特征。本标准适用于以纺织机织物为主要面料生产的文胸,包括有衬垫、无衬垫的文胸。

Woven brassiere

FZ/T 81018-2014 机织人造革服装

本标准规定了机织人造革服装产品的要求、检测方法、检验分类规则,以及标志、包装、运输和贮存等全部技术特征。本标准适用于以人造革(纺织机织物为基布)为主要面料生产的服装。本标准不适用于年龄在36个月及以下的婴幼儿服装。

Woven artificial leather garments

FZ/T 81019-2014 灯芯绒服装

本标准规定了灯芯绒服装的要求、检测方法、检验分类规则,以及标志、包装、运输和贮存等全部技术特征。本标准适用于以机织灯芯绒为主要面料生产的服装,平绒面料服装可参照执行。本标准不适用于年龄在36个月及以下的婴幼儿服装。

Corduroy wear

FZ/T 81021-2014 机织泳装

本标准规定了机织泳装的要求、检测方法、检验分类规则,以及标志、包装、运输和贮存等全部技术特征。本标准适用于以纺织机织物为主要面料生产的泳装和泳帽。本标准不适用于年龄在36个月及以下的婴幼儿泳装和泳帽。

Woven swimming wear

FZ/T 81009-2014 人造毛皮服装

本标准规定了人造毛皮服装的要求、检测方法、检验分类规则,以及标志、包装、运输和贮存等全部技术特征。本标准适用于以化学纤维为主要原料,采用有较长毛茸的仿毛皮织物为主要面料生产的人造毛皮服装。其他人造毛皮服装可参照执行。本标准不适用于年龄在36个月及以下的婴幼儿服装。

Artificial fur garment

DB32/T 2693-2014 地理标志产品 南通蓝印花布

本标准规定了南通蓝印花布的地理标志产品保护范围、术语和定义、技术要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于国家质量监督检验检疫行政主管部门根据《地理标志产品保护规定》批准保护的南通蓝印花布。

Geographical indication product Nantong blue calico

DB35/T 1434-2014 休闲服装

本标准规定了休闲服装的要求、检测方法、检验规则及标志、包装、运输和贮存。 本标准适用于以机织物为主要面料或机织物与其他服装面料拼接生产的休闲上装。

Casual Clothing

DIN CEN/TR 16596:2014 垃圾收集车辆(RCV)带底盘驾驶室和车身之间的电力电子接口; 德文版本CEN/TR 16596-2013

Electric-electronic interface between chassis-cab and bodywork of refuse collection vehicles (RCVs); German version CEN/TR 16596:2013

DIN EN 13402-3:2014 服装型号的名称与符号.第3部分:测量方法和间隔期.德文版本EN 13402-3-2013

Size designation of clothes - Part 3: Body measurements and intervals; German version EN 13402-3:2013

ASTM F1959/F1959M-14 测定服装材料电弧额定值的标准试验方法

5.1 This test method is intended for the determination of the arc rating of a material, or a combination of materials. 5.1.1 Because of the variability of the arc exposure, different heat transmission values may be observed at individual sensors. Evaluate the results of each sensor in accordance with Section 12. 5.2 This test method maintains the specimen in a static, vertical position and does not involve movement except that resulting from the exposure. 5.3 This test method specifies a standard set of exposure conditions. Different exposure conditions may produce different results. In addition to the standard set of exposure conditions, other conditions representative of the expected hazard may be used and shall be documented in the reporting of the testing results. 1.1 This test method is used to measure the arc rating of materials intended for use as flame resistant clothing for workers exposed to electric arcs that would generate heat flux rates from 84 to 25 120 kW/m28201;[2 to 600 cal/cm2s]. 1.2 This test method will measure the arc rating of materials which meet the following requirements: less than 150 mm [6 in.] char length and less than 2 s afterflame when tested in accordance with Test Method D6413. 1.2.1 It is not the intent of this test method to evaluate non flame-resistant materials except where used as under layers in multiple-layer specimens. 1.3 The materials used in this test method are in the form of flat specimens. 1.4 This test method shall be used to measure and describe the properties of materials, products, or assemblies in response to convective and radiant energy generated by an electric arc under controlled laboratory conditions. 1.5 The values stated in SI units shall be regarded as standard except as noted. Within the text, alternate units are shown in brackets. The values stated in each system may not be exact equivalents therefore alternate systems must be used independently of the other. Combining values from the systems described in the text may result in nonconformance with the method. 1.6 This test method does not apply to electrical contact or electrical shock hazards. 1.7 This standard shall not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. For specific precautions, see Section 7.

Standard Test Method for Determining the Arc Rating of Materials for Clothing

ASTM D7021-14 浴衣, 晨衣, 便服, 睡衣和睡裤纤维织物的标准性能规范

4.1 Fabrics intended for this end-use should meet all of the requirements listed in Table 1. 4.2 It should be recognized that fabric can be produced utilizing an almost infinite number of combination of construction variables (e.g., type of fibers, percentage of fibers, yarn twist, yarn number, warp and pick count, chemical and mechanical finishes). Additionally, fashion or aesthetics dictate that the ultimate consumer may find acceptable articles made from fabrics that do not conform to all of the requirements in Table 1. 4.2.1 Hence, no single performance specification can possibly apply to all the various fabrics that could be utilized for this end-use. 4.3 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods. 1.1 This performance specification covers fabrics used in bathrobes, dressing gowns, negligee, nightgown, and pajamas. 1.2 These requirements apply to the length and width directions for those properties where each fabric direction is pertinent. 1.3 The following safety hazards caveat pertains only to the test methods described in this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Performance Specification for Bathrobe, Dressing Gown, Negligee, Nightgown, and Pajama Fabrics

ASTM D2051-14 拉链表面漆耐洗烫性能的标准试验方法

5.1 Test Method D2051 is useful for testing to determine the effect of repeated laundering on the appearance of the decorative coating of a zipper. 5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing. 5.2.1  If there are differences of practical significance between reported test results for two laboratories (or more), comparative test should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. 5.3 The test method(s) in the standard along with those in Test Methods D2052, D2053, D2054, D2057, D2058, D2059, D2060, D2061, and D2062 are a collection of proven test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because no practical methods have yet been developed or because a valid evaluation of the information resulting from existing unpublished methods requires an intimate and thorough knowledge of zippers. 1.1 This test method covers the determination of the durability of the enamel or other decorative coating of a zipper when subjected to laundering. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Durability of Finish of Zippers to Laundering

ASTM D3785-14 机织领带和围巾织物的标准性能规格

5.1 Upon mutual agreement between the purchaser and the seller, woven fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification. 5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the seller. 5.2.1 In such cases, any references to the specification shall specify that: This fabric meets ASTM Specification D3785 except for the following characteristic(s). 5.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric. 5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods. 1.1 This performance specification covers woven necktie and scarf fabrics composed of any textile fiber or mixture of textile fibers. 1.2 This performance specification is not applicable to woven fabrics used for interlinings. 1.3 These requirements apply to the length and width directions for those properties where fabric direction is pertinent. 1.3.1 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Performance Specification for Woven Necktie and Scarf Fabrics