ASTM B799-95(2014)
使用亚硫酸/二氧化硫蒸汽测定金和钯涂层孔隙度的标准试验方法
Standard Test Method for Porosity in Gold and Palladium Coatings by Sulfurous Acid/Sulfur-Dioxide Vapor
ASTM B799-95(2014) 发布历史
ASTM B799-95(2014)由美国材料与试验协会 US-ASTM 发布于 1995。
。
ASTM B799-95(2014) 使用亚硫酸/二氧化硫蒸汽测定金和钯涂层孔隙度的标准试验方法的最新版本是哪一版？
最新版本是 ASTM B799-95(2020) 。
ASTM B799-95(2014) 发布之时，引用了标准
- ASTM B374 电镀的相关标准术语*， 1996-01-09 更新
- ASTM B542 有关电触点及其使用的标准术语*， 2019-11-01 更新
- ASTM B735 用硝酸蒸气测定金属基材上金涂层孔隙率的标准试验方法
- ASTM B741 ASTM B741-95(2000)
- ASTM B765 电沉积镀层和相关金属镀层孔隙率试验的选择
- ASTM B798 通过凝胶体电极法在金属基底上的金或钯涂层中的孔隙率的标准测试方法*， 2020-04-01 更新
- ASTM B809 用湿硫黄蒸气("硫黄华")作金属涂层中孔隙率测试的标准试验方法*， 2024-01-09 更新
* 在 ASTM B799-95(2014) 发布之后有更新，请注意新发布标准的变化。
ASTM B799-95(2014)的历代版本如下：
- 2020年 ASTM B799-95(2020) 用亚硫酸/二氧化硫蒸气测定金和钯涂层孔隙率的标准试验方法
- 1995年 ASTM B799-95(2014) 使用亚硫酸/二氧化硫蒸汽测定金和钯涂层孔隙度的标准试验方法
- 1995年 ASTM B799-95(2009) 用亚硫酸/SO2蒸汽测试金和钯镀层孔隙度的标准试验方法
- 1995年 ASTM B799-95(2005) 用亚硫酸/SO2蒸汽测试金和钯镀层孔隙度的标准试验方法
- 2000年 ASTM B799-95(2000) 用亚硫酸/二氧化硫蒸气测定金和钯涂层孔隙率的标准试验方法
5.1 Gold coatings are often specified for the contacts of separable electrical connectors and other devices. Electrodeposits are the form of gold that is most used on contacts, although it is also employed as inlay or clad metal and as weldments on the contact surface. The intrinsic nobility of gold enables it to resist the formation of insulating oxide films that could interfere with reliable contact operation.
5.2 Palladium coatings are sometimes specified as alternatives to gold on electrical contacts and similar electrical component surfaces, both as electrodeposits and as inlay or clad metal. This test method is particularly suitable for determining porosity in palladium coatings, since the reactive atmosphere that is used does not attack the palladium if the specified test conditions are followed. In contrast, palladium coatings are attacked by nitric acid (HNO3) and other strong oxidizing agents, so that Test Method B735 cannot be used for determining the porosity in such coatings.
5.3 In order for these coatings to function as intended, porosity, cracks, and other defects in the coating that expose base-metal substrates and underplates must be minimal or absent, except in those cases where it is feasible to use the contacts in structures that shield the surface from the environment or where corrosion inhibiting surface treatments for the deposit are employed. The level of porosity in the coating that may be tolerable depends on the severity of the environment to the underplate or substrate, design factors for the contact device like the force with which it is mated, circuit parameters, and the reliability of contact operation that it is necessary to maintain. Also, when present, the location of pores on the surface is important. If the pores are few in number and are outside of the zone of contact of the mating surfaces, their presence can often be tolerated.
5.4 Methods for determining pores on a contact surface are most suitable if they enable their precise location and numbers to be determined. Contact surfaces are often curved or irregular in shape, and testing methods should be suitable for them. In addition, the severity of porosity-determining tests may vary from procedures capable of detecting all porosity to procedures that detect only highly porous conditions.
5.5 The present test method is capable of detecting virtually all porosity or other defects that could participate in corrosion reactions with the substrate or underplate. The test is rapid, simple, and inexpensive. In addition, it can be used on contacts having complex geometry such as pin-socket contacts (although with deep recesses it is preferred that the contact structures be opened to permit reaction of the sulfur dioxide with the interior significant surfaces).
5.6 The relationship of porosity levels revealed by particular tests to contact behavior must be made by the user of these tests through practical experience or by judgment. Thus, absence of porosity in the coating may be a requirement for some applications, while a few pores in the contact zone may be acceptable for others.
5.7 This test is considered destructive in that it reveals the p......
- 标准号
- ASTM B799-95(2014)
- 发布
- 1995年
- 发布单位
- 美国材料与试验协会
- 替代标准
- ASTM B799-95(2020)
- 当前最新
- ASTM B799-95(2020)
- 引用标准
- ASTM B374 ASTM B542 ASTM B735 ASTM B741 ASTM B765 ASTM B798 ASTM B809
ASTM B799-95(2014)相似标准
推荐
【虹润冠名】656项行业标准批准发布，多项与仪表行业相关
2021-01-0133 JB/T 10761-2020土方机械 压路机压实度测量仪本标准规定了压路机用压实度测量仪的术语和定义、组成、要求、试验方法、检验规则及标志、包装、运输和贮存。本标准适用于安装在各种压路机上的机载式压实度测量仪。...
【检测】出厂检验常见理化指标检验方法及标准变化情况讲解（包括水分、蛋白、脂肪、氯化物、过氧化值等）！
本标准的佛尔哈德法(间接沉淀滴定法)和银量法(摩尔法或直接滴定法)不适用于深颜色食品中氯化物的测定。2.实验中所用水必须为去离子水，所用器具必须用去离子水润洗，自来水含有氯离子，会影响结果。第六节食品中二氧化硫含量测定（GB 5009.34-2016）二氧化硫类物质通过生成亚硫酸，亚硫酸对食品有漂白和防腐作用。硫磺燃烧产生二氧化硫，遇水形成亚硫酸。亚硫酸盐与酸反应产生二氧化硫，后者遇水形成亚硫酸。...
电化学传感器的组成及应用
用于测定相对湿度的涂覆压电石英晶体用传感器,通过光刻和化学蚀刻技术制成小型石英夺电晶体,在AT 切割的10MHZ石英晶体上涂有4种物质,对湿度具有较高的质量敏感性.该晶体是振荡电路中的共振器,其频率随质量变化,选择适当涂层,该传感器可用于测定不同气体的相对湿度.该传感器的灵敏度、响应线性、响应时间、选择性、滞后现象和使用寿命等取决于涂层化学物质的性质。 ...
各类实验室常用仪器设备配置清单，请收好！
、水色 红外水分测定仪，检测水分 糖度计，检测糖度亚硫酸盐定量检测装置，检测亚硫酸盐（二氧化硫） 分析天平，称量 旋转蒸馏仪，提纯试剂 二次蒸馏装置，提纯试剂 离心机，农残检测前处理 电热鼓风干燥箱，农残检测前处理 数字式PH计 超净工作台，微生物检测 通风柜，农残检测前处理 生化培养箱，微生物检测 氮吹仪，农残检测前处理 隔水式培养箱，微生物检测 电热恒温培养箱，微生物检测 压力蒸汽消毒器，微生物检测...