V18 冷加工工艺 标准查询与下载
共找到 335 条与 冷加工工艺 相关的标准，共 23 页
This standard specifies the procedure for the visual examination of cable ties for harnesses for aerospace applications.
Aerospace Series Heat Resisting Alloy NI-PH2601 Solution Treated and Cold Worked Bar for Forged Fasteners D Less Than or Equal to 50 mm 1270 MPa Less Than or Equal to Rm Less Than or Equal to 1550 MPa Edition P 3
- ICS
- 77.040.20
- CCS
- V18
- 发布
- 1995
- 实施
本标准规定了金属镀覆和化学覆盖工艺质量控制的通用原则和基本要求。 本标准适用于航空产品各种材料和零件的金属镀覆和化学覆盖工艺的质量控制，金属的化学铣切、酸洗、光化学刻蚀等工艺亦可参照使用。
Metal Plating and Chemical Covering Process Quality Control
- ICS
- CCS
- V18
- 发布
- 1994-10-31
- 实施
- 1995-01-01
本标准规定了钛合金紧固件离子镀铝工艺及要求。 本标准适用于钛合金紧固件离子镀铝。
Ion Plating Aluminum Process for Titanium Alloy Fasteners
- ICS
- CCS
- V18
- 发布
- 1994-10-31
- 实施
- 1995-01-01
This document is applicable to the room-temperature bending longitudinal and transverse to the direction of rolling of light-metal sheets and strips. It provides the minimum bending radii for a bending angle of 90?
Aerospace - Bending of light metal sheets and strips - Part 3: Bending radii, directions for design
- ICS
- 49.035
- CCS
- V18
- 发布
- 1994-08
- 实施
Typical combination of cold stamping die Typical combination of composite B-type thin die
- ICS
- CCS
- V18
- 发布
- 1994-06-01
- 实施
- 1994-06-01
本标准规定了冷冲?湫妥楹系募际跻蟆⒀槭展嬖蚣鞍霸耸涞纫蟆? 本标准适用于HB 6828.1～6828.9。
Typical combination technical conditions of cold stamping die
- ICS
- CCS
- V18
- 发布
- 1994-06-01
- 实施
- 1994-06-01
Typical combination of cold stamping die Typical combination of guide plate longitudinal feeding
- ICS
- CCS
- V18
- 发布
- 1994-06-01
- 实施
- 1994-06-01
Typical combination of cold stamping die Typical combination of guide plate type lateral feeding
- ICS
- CCS
- V18
- 发布
- 1994-06-01
- 实施
- 1994-06-01
Typical combination of cold stamping die Type A typical combination of spring pressure unloading
- ICS
- CCS
- V18
- 发布
- 1994-06-01
- 实施
- 1994-06-01
Typical combination of cold stamping die Spring pressure discharge type B typical combination
- ICS
- CCS
- V18
- 发布
- 1994-06-01
- 实施
- 1994-06-01
Typical combination of cold stamping die Typical combination of fixed unloading
- ICS
- CCS
- V18
- 发布
- 1994-06-01
- 实施
- 1994-06-01
Typical combination of cold stamping die Typical combination of composite A-type thick die
- ICS
- CCS
- V18
- 发布
- 1994-06-01
- 实施
- 1994-06-01
Typical combination of cold stamping die Typical combination of composite B-type thick die
- ICS
- CCS
- V18
- 发布
- 1994-06-01
- 实施
- 1994-06-01
Typical combination of cold stamping die Typical combination of composite A-type thin die
- ICS
- CCS
- V18
- 发布
- 1994-06-01
- 实施
- 1994-06-01
This standard defines the characteristics of nickel plated copper ring shaped terminals for crimping on nickel plated copper conductors. They are for use on both metric and inch dimension studs at temperatures up to 260 °C maximum. This standard should be used in conjunction with EN 3373-001.
Aerospace Series Heat Resisting Alloy NI-PH2601 Solution Treated Bar for Machined Fasteners D is Less Than or Equal to 50 mm Rm is Greater Than or Equal to 1270 MPa Edition P 2
- ICS
- 77.040.20
- CCS
- V18
- 发布
- 1994-03-31
- 实施
This standard specifies the requirements relating to nickel base braze filler metal NT-B40002 in tape form for aerospace appplications.
Aerospace Series Nickel Base Alloy NI-B40002 Filler Metal for Brazing Tape Edition P1
- ICS
- 77.150.30
- CCS
- V18
- 发布
- 1994-01-31
- 实施
This standard specifies the required characteristics for lamp, code 718, used on-board aircraft. It shall be used together with EN 2756.
Aerospace Series Nickel Base Alloy NI-B40002 Filler Metal for Brazing Powder or Paste Edition P1
- ICS
- 77.150.30
- CCS
- V18
- 发布
- 1994-01-31
- 实施
This standard specifies the characteristics of straight swivel nuts for pipe couplings, 60°, spherical, in TI-P64001, for aerospace applications.
Aerospace Series Aluminium Alloy AL-P2219-T62 Sheet and Strip 0,5 mm Less Than or Equal to a Less Than or Equal to 6 mm Edition P1
- ICS
- 77.120.10
- CCS
- V18
- 发布
- 1993-08-31
- 实施
This standard specifies the required characteristics for lamp, code 338, used on-board aircraft. It shall be used together with EN 2756.
Aerospace Series Aluminium Alloy AL-P2219-T81 Clad Sheet and Strip 0,5 mm Less Than or Equal to a Less Than or Equal to 6 mm Edition P1
- ICS
- 77.120.10
- CCS
- V18
- 发布
- 1993-08-31
- 实施
This standard specifies the dimensions and tolerances of filler metal for brazing , in tape , thickness 0,075mm≤a≤1,5mm, for aerospace applications.
Aerospace Series Aluminium Alloy AL-2024-T4 Sheet and Strip with Improved Stretch Forming Capability 0,4 mm Less Than or Equal to a Less Than or Equal to 6 mm Edition P1
- ICS
- 77.120.10
- CCS
- V18
- 发布
- 1993-08-31
- 实施
