29.160.20 发电机 标准查询与下载

DL/T 298-2023 发电机定子绕组端部电晕检测与评定导则

本文件规定了使用暗室目测和紫外成像装置进行发电机定子绕组端部电晕检测的方法和评定的标准。 本文件适用于定子额定电压在10.5 kV及以上的发电机及调相机，其他旋转电机可参照执行。

Guidelines for Corona Detection and Assessment at Ends of Generator Stator Windings

DL/T 735-2023 大型汽轮发电机定子绕组端部动态特性的测量及评定

本文件规定了采用锤击法进行汽轮发电机定子绕组端部动态特性测量的方法及评定准则。 本文件适用于额定功率200MW及以上、额定转速为3000r/min及3600r/min的2极汽轮发电机和转速为1500r/min及1800r/min的4极汽轮发电机。 额定功率在200MW以下的汽轮发电机、以及额定容量在300MVA及以下的同步调相机可参照本文件执行。

Measurement and Evaluation of Dynamic Characteristics of Stator Winding Ends of Large Turbine Generators

NB/T 11232-2023 风力发电机组电气系统能耗要求及测量方法

Wind turbine electrical system energy consumption requirements and measurement methods

23/30458350 DC BS EN 50549-1 AMD 1. 发电厂与配电网并联的要求 第 1 部分：连接到低压配电网 B 型以下发电厂

BS EN 50549-1 AMD 1. Requirements for generating plants to be connected in parallel with distribution networks - Part 1. Connection to a LV distribution network. Generating plants up to and including Type B

23/30458353 DC BS EN 50549-2 AMD 1. 发电厂与配电网并联的要求 第 2 部分：与中压配电网的连接 B 型以下发电厂

BS EN 50549-2 AMD 1. Requirements for generating plants to be connected in parallel with distribution networks - Part 2. Connection to a MV distribution network. Generating plants up to and including Type B

T/CEEIA 630-2022 隐极同步发电机内冷水系统技术要求

本文件规定了隐极同步发电机内冷水系统的环境条件、设计、制造、现场安装、现场使用、图样及文件、铭牌、标识、包装、运输和贮存的技术要求。 本文件适用于隐极同步发电机内冷水系统，包括内冷水系统整体及各部套件。

Specific requirements for inner cooling water system of cylindrical rotor synchronous machines

T/ZZB 2821-2022 汽轮发电机组用发电机

本文件规定了汽轮发电机组用发电机的术语和定义、 型式与基本参数、 基本要求、 技术要求、试验方法、检验规则、标志、包装、运输、 贮存及安装、质量承诺。 本文件适用于电压等级为 13.8 kV 及以下，额定频率为 50 Hz，额定功率为 100 MW 及以下的汽轮发电机组用发电机（以下简称发电机）。

Turbine generators

BS EN 50549-10:2022 发电厂与配电网并联的要求 发电机组合格评定试验

The purpose of this document is to provide technical guidance for tests on generating units and interface protection to evaluate their electrical characteristics. The evaluation results are intended to be used to demonstrate conformity of generating units to technical requirements for grid connection. In this context the evaluation results can also be used as part of a certification programme. transformer, cabling, multiple units) are considered in the evaluation of the final installation of a generating plant. The requirements to be evaluated are covered in the following standardization documents: – EN 50549-1:2019: Requirements for generating plants to be connected in parallel with distribution networks - Part 1: connection to a LV distribution network - Generating plants up to and including Type B – EN 50549-2:2019: Requirements for generating plants to be connected in parallel with distribution networks - Part 2: Connection to a MV distribution network - Generating plants up to and including Type B If grid connection requirements are dealt with in other documents or for other generating module types, where no specific testing procedure is provided, testing methods of this document can be used if applicable. This document provides evaluation criteria for the conformity assessment of generating units with respect to the abovementioned standardization documents, based on type testing. However, some requirements are applicable on the generating plant level. The assessment of the conformity to these plant requirements are out of the scope of this document. Nevertheless, this document may be used to show the capabilities of a generating unit to be used in a plant. As a consequence, it is possible that the conformity assessment of a generating unit does not cover all aspects of the above-mentioned standardization documents, typically when a requirement is evaluated on a plant level. Therefore, the conformity assessment report indicates clearly which clauses of this document are covered and which clauses are not covered. This document recognizes the existence of specific technical test requirements within several member states that must be complied with.

Requirements for generating plants to be connected in parallel with distribution networks - Tests for conformity assessment of generating units

EN 50549-10:2022 发电厂与配电网并联的要求 第10部分：发电机组合格评定试验

The purpose of this document is to provide technical guidance for tests on generating units and interface protection to evaluate their electrical characteristics. NOTE 1 Mechanical issues are taken into account as far as they influence the electrical characteristics. The evaluation results are intended to be used to demonstrate conformity of generating units to technical requirements for grid connection. In this context the evaluation results can also be used as part of a certification programme. NOTE 2 Besides the type test results of the generating unit all additional elements for connection to the grid (e.g. transformer, cabling, multiple units) are considered in the evaluation of the final installation of a generating plant. The requirements to be evaluated are covered in the following standardization documents: – EN 50549 1:2019: Requirements for generating plants to be connected in parallel with distribution networks - Part 1: connection to a LV distribution network - Generating plants up to and including Type B – EN 50549 2:2019: Requirements for generating plants to be connected in parallel with distribution networks - Part 2: Connection to a MV distribution network - Generating plants up to and including Type B If grid connection requirements are dealt with in other documents or for other generating module types, where no specific testing procedure is provided, testing methods of this document can be used if applicable. This document provides evaluation criteria for the conformity assessment of generating units with respect to the abovementioned standardization documents, based on type testing. However, some requirements are applicable on the generating plant level. The assessment of the conformity to these plant requirements are out of the scope of this document. Nevertheless, this document may be used to show the capabilities of a generating unit to be used in a plant. As a consequence, it is possible that the conformity assessment of a generating unit does not cover all aspects of the above-mentioned standardization documents, typically when a requirement is evaluated on a plant level. Therefore, the conformity assessment report indicates clearly which clauses of this document are covered and which clauses are not covered. This document recognizes the existence of specific technical test requirements within several member states that must be complied with.

Requirements for generating plants to be connected in parallel with distribution networks - Part 10: Tests for conformity assessment of generating units

CSA C22.2 No.60079-26-2022 爆炸性环境 第26部分：具有分离元件或组合防护等级的设备

1 Scope This part of IEC 60079 specifies requirements for construction, testing and marking for Ex Equipment that contains parts of the equipment with different Equipment Protection Levels (EPLs) and a separation element. This equipment is mounted across a boundary where different EPLs are required, for example between different gas hazardous areas, dust hazardous areas or gas hazardous areas adjacent to dust hazardous areas. EXAMPLE: Equipment installed in the wall of storage tanks located in Zone 1 and containing Zone 0 inside. Separation elements are considered for both electrical and non-electrical equipment. If mechanical energy can be transformed into a potential ignition source, additionally an ignition hazard assessment in accordance with ISO 80079-36 is performed and appropriate measures are undertaken. Suitable measures can be selected from ISO 80079-37 or IEC TS 60079-42. This document also specifies requirements for the combination of two Types of Protection, each with EPL Gb, to achieve EPL Ga. Examples are included in 4.2. This document supplements and modifies the general requirements of IEC 60079-0. Where a requirement of this document conflicts with a requirement of IEC 60079-0, the requirement of this document takes precedence. The requirements of the IEC 60079 series of Standards cover protection with respect to explosion hazard only. The CSA C22.2 No. 60079 series of Standards (based on the adoption of corresponding IEC Standards) is to be used in conjunction with other applicable Standards containing the appropriate electrical safety requirements for general use equipment. This Standard applies to electrical installation systems intended to be installed or used in accordance with CSA C22.1, Canadian Electrical Code Part I. General requirements applicable to electrical products are provided in CSA C22.2 No. 0. Note 1A: The ISO 80079 series of Standards provide guidance for evaluating non-electrical risk; however, at the time of publication of this Standard they have not been adopted as Canadian standards.

Explosive atmospheres — Part 26: Equipment with separation elements or combined levels of protection Atmosphères explosives — Partie 26 : Appareil avec éléments de séparation ou niveaux de protection combinés

T/CSEE 0284-2022 氢冷发电机吸附再生式气体干燥器技术条件

本文件规定了氢冷发电机配套的吸附再生式气体干燥器的基本技术要求、检查与试验、检验规则、标识、包装、运输与贮存、运行与维护及常见故障与处理措施。 本文件适用于氢冷发电机吸附再生式气体干燥器（以下简称干燥器）的设计、制造、检验、验收、运行及维护。

Technical conditions of hydrogen-cooled generator adsorption regenerative gas dryer

T/CSEE 0282-2022 火力发电厂励磁装置状态评价导则

本文件规定了火力发电厂励磁装置状态评价方法和要求。 本文件适用于 100 MW 及以上火力发电机组励磁装置状态评价。其他机组可参照执行。

Guidelines for condition evaluation of excitation devices in thermal power plants

T/CSEE 0283-2022 氢冷发电机氢气提纯净化装置技术条件

本文件规定了氢冷发电机氢气提纯净化装置的基本技术要求、检查与试验、检验规则、标识、包装、运输和贮存、常见故障与处理措施。 本文件适用于氢冷发电机氢气提纯净化装置（以下简称净化装置）的设计、制造、检验、验收、运行及维护。本文件中密封油真空脱气系统仅适用于独立装置，其他密封油脱气系统参照执行。

Technical conditions of hydrogen purification device for hydrogen-cooled generator

T/CEEIA 605-2022 氢冷发电机氢气提纯净化装置技术条件

本文件规定了氢冷发电机氢气提纯净化装置的基本技术要求、检查与试验、检验规则、标识、包装、运输和贮存、常见故障与处理措施。 本文件适用于氢冷发电机氢气提纯净化装置(以下简称净化装置) 的设计、制造、检验、验收、运行及维护。本文件中密封油真空脱气系统仅适用于独立装置，其他密封油脱气系统参照执行。

Technical requirements of the hydrogen purification device forhydrogen-cooled generators

T/CEEIA 606-2022 氢冷发电机吸附再生式气体干燥器技术条件

本文件规定了氢冷发电机配套的吸附再生式气体干燥器的基本技术要求、检查与试验、检验规则、标识、包装、运输与贮存、运行与维护及常见故障与处理措施。本文件适用于氢冷发电机吸附再生式气体干燥器(以下简称干燥器的设计、制造、检验、验收、运行及维护。

Technical requirements of the adsorption regeneration gas dryer forhydrogen-cooled generators

T/CEEMA 002-2022 煤电机组发电机节能、供热和灵活性改造技术导则

煤电机组发电机节能、供热、灵活性改造相关术语和定义。 煤电机组发电机节能、供热、灵活性改造的总体和具体要求。

Technical guide for energy conservation, heating, flexibility retrofits of coal-fired power generators

NB/T 31064-2022 海上双馈风力发电机技术规范

Technical specifications for offshore doubly-fed wind turbines

NB/T 31063-2022 海上永磁同步风力发电机技术规范

Technical specifications for offshore permanent magnet synchronous wind turbines

IEC 60034-33:2022 旋转电机第33部分:包括电动发电机在内的同步水轮发电机特殊要求

Rotating electrical machines - Part 33: Synchronous hydrogenerators including motor-generators - Specific requirements

DL/T 1766.3-2021 水氢氢冷汽轮发电机检修导则 第5部分：内冷水系统检修

Maintenance guideline for water-hydrogen hydrogen-cooled turbogenerators Part 5: Maintenance of internal cooling water system