29.160.20 发电机 标准查询与下载

T/CEEIA 361-2019 风力发电机组预警技术导则

本标准对风力发电机组预警功能的一般原则和技术要求进行定义，包括预警的定义、系统功能、和技术要求等做出了定义和要求。 本标准适用于单机容量大于或等于1.0MW的水平轴风力发电机组。其它的风电机组可根据自身特点参照使用。

Technical guidelines for early warning of wind turbine generator system

EN 50549-1:2019/AC:2019-04 发电厂与配电网络并联的要求 第1部分：连接到低压配电网络 发电厂直至并包括 B 型

These standards provide technical requirements for the connection of generating plants up to and including Type A (-1-1)/ Type B (-1-2) which can be operated in parallel with a public LV distribution network. They are intended to be used as a technical reference for connection agreements between DNOs and electricity producers and to demonstrate compliance with COMMISSION REGULATION (EU) 2016/631 (Requirements for Generators).

Requirements for generating plants to be connected in parallel with distribution networks - Part 1: Connection to a LV distribution network - Generating plants up to and including Type B

T/CSEE 0094-2019 发电机中性点经变压器接地成套装置技术条件

本标准规定了发电机中性点经变压器接地成套装置（简称接地成套装置）的使用条件、技术要求、试验、标志、包装、运输、贮存及产品文件。本标准适用于额定电压27kV及以下、额定频率50Hz或60Hz、采用经变压器接地的高电阻和高阻抗接地方式的汽轮发电机（含核电机组）、水轮发电机接地成套装置，其它机组的接地成套装置可参照执行。

Technical conditions of complete set of equipment for generator neutral point grounding through transformer

KS I 4001-2018(2023) 客车用再制造交流发电机试验方法

Test methods of remanufactured alternator for passenger cars

KS I 4001-2018 客车用再制造交流发电机试验方法

Test methods of remanufactured alternator for passenger cars

KS I 4024-2018(2023) 轻型商用车用再制造风扇离合器试验方法

Test methods of remanufactured fan clutch for light-duty commercial vehicles

KS I 4024-2018 轻型商用车再制风机离合器试验方法

Test methods of remanufactured fan clutch for light-duty commercial vehicles

DB15/T 1277-2017 沼气发电机组运行管理规范

Operation management specification for biogas generator set

CSA B138.1-17/B138.2-2017 便携式燃油设备 成套设备要求/安装要求

1.1 This Standard is arranged in two parts, as follows: a) CSA B138.1 covers requirements for manufacturing, testing, marking, and manufacturer’s instructions of portable oil-burning equipment; and b) CSA B138.2 covers requirements for installation of portable oil-burning equipment including field installed ancillary equipment required for operation of the portable oil-burning equipment. 1.2 This Standard, CSA B138.1, applies to portable oil-burning equipment which is operated while stationary and may be relocated to other locations. The products covered by this Standard may include oil-burning appliances, their fuel systems, related components and accessories, and their associated electrical features. Portable oil-burning equipment covered by this Standard may incorporate internal combustion engines, power generating equipment, or other shaft-driven process equipment. 1.3 This Standard provides minimum requirements for components used in portable oil-burning equipment, that include but are not limited to a) piping and tubing systems; b) fuel transfer pumps; c) control devices; d) tank fill and venting systems; e) appliance venting systems; f) packaged equipment enclosures; g) skid, trailer or vehicle mount; and h) electrical wiring. 1.4 This Standard does not apply to a) stationary oil-burning equipment which would otherwise be subject to the requirements of CSA B139 and the Canadian Electrical Code, Part I; b) power generating systems with an output voltage greater than 15 kV; c) power generating systems rated greater than 4 MW; d) a portable oil-burning appliance with a fuel system which has a fuel tank capacity of 45 L (10 gal) or less; e) power generating systems with single phase electrical output ratings of 12 kW or less at 240 V or less; f) portable equipment incorporating internal combustion engines other than generators, rated at 25 brake horsepower or less; or g) appliances installed in mobile housing, recreational vehicles, and marine craft. 1.5 The Transportation of Dangerous Goods Act (TDG) and the Transportation of Dangerous Goods Regulations can set out requirements that are additional to or different from those in this Standard due to particular characteristics or properties or individual dangerous goods. Where there is an inconsistency between the requirements of this Standard and those of the Act or Regulations, the Act or Regulations prevail to the extent of the inconsistency. 1.6 In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (nonmandatory) to define their application. 1.7 The values given in SI (metric) units are the standard. The values given in parentheses are for information only.

Portable oil-burning equipment — Packaged equipment requirements/Installation requirements

T/CSEE /Z0013-2016 同步发电机进相试验进相能力计算导则

本指导性技术文件规定了同步发电机进相试验进相能力的计算原则、计算条件、计算内容及对计算报告的要求等。  本指导性技术文件适用于同步发电机进相试验进相能力计算，同步调相机及抽水蓄能发电机的进相试验进相能力计算可参照执行。

Guide for leading power factor ability calculation of synchronous

NB/T 42079-2016 小水电机组励磁功率单元技术条件

Technical conditions of excitation power unit of small hydropower unit

NB/T 31100-2016 电励磁同步风力发电机技术条件

Technical conditions of electrically excited synchronous wind turbine

DIN CLC/TS 50549-1:2016 发电厂与配电网络并联的要求 第1部分：连接到 16 A 以上的低压配电网络；德文版 CLC/TS 50549-1:2015

Requirements for generating plants to be connected in parallel with distribution networks - Part 1: Connection to a LV distribution network above 16 A; German version CLC/TS 50549-1:2015

DIN CLC/TS 50549-2:2016 与配电网络并联的发电厂的要求 第2部分：连接到 MV 配电网络；德文版 CLC/TS 50549-2:2015

Requirements for generating plants to be connected in parallel with distribution networks - Part 2: Connection to a MV distribution network; German version CLC/TS 50549-2:2015

T/CEEIA 232-2016 QFX系列节能型箱式发电机（3MW~60MW）技术条件

本标准规定了结构型式、基本参数，技术要求，试验检查项目和验收规则，标志、包装及保证期及随机文件。

Technical Requirement for Series QFX Box Type Generator

GOST IEC 60034-3-2015 旋转电机. 第3部分. 用蒸汽涡轮机或燃气涡轮机驱动的同步发电机用特殊需求

Rotating electrical machines. Part 3. Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines

DB44/T 1499-2014 小型风光互补发电系统控制器

本标准规定了小型风光互补发电系统控制器（以下简称控制器）的要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于风力发电和光伏发电混合功率在20 kW以下的离网型风光互补发电系统用控制器。发电混合功率在20 kW～100 kW的控制器可参照使用。

Controller for small wind-solar hybrid power generation system

NB/T 31064-2014 海上双馈风力发电机技术条件

本标准规定了并网型风力发电机组用海上双馈风力发电机的主要型式、技术要求、试验方法和检验规则、安全和警示标志、产品信息、包装、运输与贮存等要求。 本标准适用于海上安装的风力发电机组使用的双馈风力发电机(以下简称发电机)。

Technical specifications for off-shore type double-fed wind generator

NB/T 31063-2014 海上永磁同步风力发电机

本标准规定了并网型风力发电机组用海上永磁同步风力发电机的主要型式、技术要求、试验方法和检验规则、标志、包装、保证期等要求。 本标准适用于海上安装的永磁同步发电机组使用的永磁同步风力发电机(以下简称发电机)。

Permanent magnetic synchronous generator for off-shore wind turbine

GSO 2409:2014 石油和天然气工业 蒸汽热发生器的制造

This specification covers the minimum requirements for the manufacture of new Heat Recovery Steam Generator Unit downstream of a Combustion Gas Turbine (CGT) (herein referred to as HRSG).

Petroleum and natural gas industries – Manufacture of Heat Recovery Steam Generators