81.060.10 原料 标准查询与下载

JC/T 1097-2009 建筑卫生陶瓷用添加剂.解胶剂

本标准规定了建筑卫生陶瓷用解胶剂的术语和定义、产品分类、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于建筑卫生陶瓷用解胶剂。

Additives for building and sanitary ceramic:dispergators

JC/T 1094-2009 陶瓷用硅酸锆

本标准规定了陶瓷用硅酸锆的术语和定义、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于建筑陶瓷、卫生陶瓷、日用陶瓷等陶瓷产品用硅酸锆。

Zirconium silicate for ceramic

KS L 9501-2009 工业用石灰

이 표준은 공업에 사용하는 석회(이하 공업용 석회라 한다.)에 대하여 규정한다. 다만 재생

Industrial lime

JIS R 9112 AMD 1:2009 陶瓷模型用熟石膏的物理试验方法(修改件1)

This translation has been made based on the Amendment to the origi- nal Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee as the result of proposal for revision of Japanese Industrial Standard with the draft being attached, based on the provi- sion of Article 12 Clause 1 of the Industrial Standardization Law ap- plicable to the case of revision by the provision of Article 14. Consequently, JIS R 9112:1978 is partially replaced with this Amend- ment.

Method of Physical Test for Plaster of Paris Mold for Pottery (Amendment 1)

JIS R 9151 AMD 1:2009 普通水泥缓凝剂用石膏(修改件1)

This translation has been made based on the Amendment to the origi- nal Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee as the result of proposal for revision of Japanese Industrial Standard with the draft being attached, based on the provi" sion of Article 12 Clause 1 of the Industrial Standardization Law ap- plicable to the case of revision by the provision of Article 14. Consequently, JIS R 9151:1979 is partially replaced with this Amend- ment.

Gypsum for Portland Cement Retarder (Amendment 1)

JIS R 9111 AMD 1:2009 陶瓷模型用熟石膏(修改件1)

This translation has been made based on the Amendment to the origi- nal Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee as the result of proposal for revision of Japanese Industrial Standard with the draft being attached, based on the provi- sion of Article 12 Clause 1 of the Industrial Standardization Law ap- plicable to the case of revision by the provision of Article 14. Consequently, JIS R 9111:1977 is partially replaced with this Amend- ment.

Plaster of Paris Mold for Pottery (Amendment 1)

ASTM C690-09(2014) 采用电感应区域技术的矾土或石英粉末粒径分布的标准试验方法

3.1 This test method is useful to both sellers and purchasers of alumina and quartz powders for determining particle size distributions for materials specifications, manufacturing control, and development and research. 1.1 This test method, one of several found valuable for the measurement of particle size, covers the determination of the particle size distribution of alumina or quartz powders (0.6 to 56.0 μm) using electrical sensing zone particle size analyzers. These instruments use an electric current path of small dimensions which is modulated by individual particle passage through an aperture, and produces individual pulses of amplitude proportional to the particle volume. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Particle Size Distribution of Alumina or Quartz Powders by Electrical Sensing Zone Technique

ASTM C326-09(2014) 白陶瓷品用粘土干燥和烧缩的标准试验方法

2.1 The purpose of this test is to obtain values of shrinkage after drying and firing of clays or bodies or both, under various processing conditions to enable designers to determine the proper size of mold or die so as to produce a predetermined size of fired ware. 1.1 This test method covers the determination of linear shrinkage of ceramic whiteware clays, both unfired and fired. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Drying and Firing Shrinkages of Ceramic Whiteware Clays

ASTM C1069-09(2014) 采用氮吸附法的氧化铝或石英特殊表面区域的标准试验方法

4.1 Both sellers and purchasers of alumina and quartz will find the test method useful to determine the specific surface area and indirectly as a measure of the particle size for material specifications, manufacturing control, and research and development. 1.1 This test method covers the determination of the specific surface area of aluminas and silicas used in the manufacture of ceramics. The test method is a general one, permitting the use of any modern commercial nitrogen adsorption apparatus but strictly defining the outgassing procedure. Calculations are based on the Brunauer-Emmett-Teller (BET) equation. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Specific Surface Area of Alumina or Quartz by Nitrogen Adsorption

ASTM C925-09(2014) 非塑性陶瓷粉末的精密电铸成形湿筛析的标准指南

4.1 Both suppliers and users of pulverized ceramic powders will find this test method useful to determine particle size distributions for materials specifications, manufacturing control, development, and research. 4.2 The test method is simple, although tedious, uses inexpensive equipment, and will provide a continuous curve with data obtained with standardized woven sieves. 1.1 This guide covers the determination of the particle size distribution of pulverized alumina and quartz for particle sizes from 45 to 5 μm by wet sieving. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.2.1 The only exception is in the Section 5, Apparatus, 5.1 where there is no relevant SI equivalent. 1.3 This standard does not purport to address the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Precision Electroformed Wet Sieve Analysis of Nonplastic Ceramic Powders

ASTM C371-09(2014) 非塑性陶瓷粉末的金属丝筛分析的标准试验方法

3.1 Sieve analyses are carried out to determine the particle size distribution of powders which, in turn, are used to qualify those materials as to their usefulness in the process under consideration. Since particle size analyses have only relative significance, the results should be considered only where they correlate with process characteristics. The parameter that is being measured in this test is the amount of material that will pass through a cloth having theoretically square openings. It must be remembered that all the holes are not square, nor uniform in size, and the question of whether a given particle will go through is a statistical one. Since each particle size analysis method measures a unique physical parameter, the results from one method may not agree with those from another. Particle size distributions play a role in such properties as bulk density, dustiness, and handling characteristics. Care should be taken, however, when interpretations are made from one or two points (sieves) on the distribution curve. 1.1 This test method covers the determination of the particle size distribution of nonplastic ceramic powders such as alumina, silica, feldspar, pyrophyllite, nepheline syenite, talc, titanates, and zircon using wire cloth sieves. 1.2 Materials containing a large amount of fines, containing agglomerates, or that are nonfree-flowing, are wet-sieved to remove excessive fines or to disperse agglomerates before performing the test. This technique is not applicable to materials that are, to any degree, water soluble. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units, or are other customary units (in the case of sieve frame diameter and sieve number), that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Wire-Cloth Sieve Analysis of Nonplastic Ceramic Powders

ASTM C1182-09 用离心测光沉淀法测定矾土的粒径分布用标准试验方法

Manufacturers and users of alumina powders will find this test method useful to determine the particle size distribution of these materials for product specification, quality control, and research and development testing.1.1 This test method covers the determination of the particle size distribution of alumina in the range from 0.1 to 20 μm having a median particle diameter from 0.5 to 5.0 μm. 1.2 The procedure described in this test method may be successfully applied to other ceramic powders in this general size range. It is the responsibility of the user to determine the applicability of this test method to other material. 1.3 The values stated in SI units are to regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining the Particle Size Distribution of Alumina by Centrifugal Photosedimentation

DIN 51096:2008 陶瓷原材料和基本材料的测试.用感应耦合等离子体光学发射光谱测定法(ICP OES)和电热蒸馏器(ETV)直接测定碳化硅粉末和颗粒中杂质的质量分率

Testing of ceramic raw and basic materials - Direct determination of mass fractions of impurities in powders and granules of silicon carbide by inductively coupled plasma optical emission spectrometry (ICP OES) and electrothermal vaporisation (ETV)

DS/EN 725-2:2008 先进技术陶瓷 陶瓷粉末的试验方法 第2部分：钛酸钡中杂质的测定

This part of EN 725 describes a method for the determination of impurities in barium titanate powders using inductively coupled plasma optical emission spectroscopy (ICP-OES).The method is applicable only to stoichiometric barium titanate. The maximum concentrations measured for each impurity are as follows: Sr 4 mg/g (4 000 ppm) Ca 500 ug/g (500 ppm) K 200 ug/g (200 ppm) Na, Mg, Al, Fe, Nb 100 µ­g/g (100 ppm)The minimum concentration or detection limits are from 1 ug/g to 5 ug/g (1 ppm to 5 ppm).

Advanced technical ceramics - Methods of test for ceramic powders - Part 2: Determination of impurities in barium titanate

DIN 51095-1:2007 陶瓷原料和基本材料的测试.非氧化陶瓷原料和基本材料的粉末和颗粒中硫含量的测定.第1部分:感应电炉中原料发酵作用后的红外测量

This draft standard specifies a method for the determination of content of sulphur in powders and granules of ceramic raw and basic materials such as silicon carbides, silicon nitrides, graphites, flame carbon black, cokes, carbon powder. The method specified is appplicable to materials with mass fractions of sulphur of 0,005 % bis 2 %.

Testing of ceramic raw and basic materials - Determination of content of sulphur in powders and granules of non-oxidic ceramic raw and basic materials - Part 1: Infrared measurement after digestion in the induction furnace

DIN 51088:2007 陶瓷原料和基本材料的测试.用发射光谱测定分析和直流电弧中的激励测定碳化硅粉末和颗粒碳化硅中金属微量杂质的质量分率

This draft standard specifies a method for the determination of metallic trace impurities in silicon carbide powders and granular silicon carbides of ceramic raw and basic materials by optical emission spectrometry and excitation in the DC arc. The method is applicable to impurities, subject to the main parameters element, wave length, arc parameters and weighted sample, with mass fractions of about 1 mg/kg to about 3000 mg/kg, after checking also to about 5000 mg/kg.#,,#

Testing of ceramic raw and basic materials - Determination of mass fractions of metallic trace impurities in silicon carbide powders and granular silicon carbides by optical emission spectrometry and excitation in the DC arc

DS/EN 725-5/AC:2007 高级技术陶瓷 陶瓷粉末的试验方法 第5部分：粒度分布的测定

This Part of EN 725 describes the preparation of suspensions and calibration of apparatus, prior to the measurement of particle size distribution of powders used for advanced technical ceramics.The preparation described is appropriate for measurements either by the sedimentation method or the laser light scattering method.

Advanced technical ceramics - Methods of test for ceramic powders - Part 5: Determination of particle size distribution

DIN 51095-2:2007 陶瓷原料和基本材料的测试.非氧化陶瓷原料和基本材料的粉末和颗粒中硫含量的测定.第2部分:氧流量中燃烧后的感应耦合等离子光发射光谱测定法(ICP OES)或离子色谱法(IC)

This draft standard specifies a method for the determination of content of sulphur in powders and granules of ceramic raw and basic materials by optical emission spectrometry by inductively coupled plasma (ICP OES) or ion chromatography (IC) after burning in an oxygen flow. It is applicable to materials with mass fractions of sulphur less than or equal to 10 %, of ignition residue less than 20 % and of barium less than 10 mg/kg. Mass fractions of sulphur of 0,5 mg/kg when determined by ICP OES and of 5 mg/kg when determined by IC are guide values for the low application range of this method.

Testing of ceramic raw and basic materials - Determination of content of sulphur in powders and granules of non-oxidic ceramic raw and basic materials - Part 2: Optical emission spectrometry by inductively coupled plasma (ICP OES) or ion chromatography (I

ASTM C325-07 陶瓷白土粘土湿筛分析标准指南

1.1 This guide covers the wet sieve analysis of ceramic whiteware clays. This guide is intended for use in testing shipments of clay as well as for plant control tests.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Wet Sieve Analysis of Ceramic Whiteware Clays

KS L 4002-2007(2017) 测试方法不含水分陶瓷粘土

Testing method for free moisture in ceramic whiteware clays