83.140.40 软管 标准查询与下载

KS M ISO 28017-2022 疏浚用钢丝或织物增强橡胶软管和软管组件规范

Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications Specification

T/SGX 015-2022 线束用自卷式保护套管 第1部分：新能源汽车

5.1.1  当用于高压线束时，套管的外观颜色为橙色；当用于低压线束时，套管的外观颜色为黑色。 5.1.2  套管的内外表面应光滑，不得有锐利边缘、毛刺、接痕或表面突出物，以免损伤线缆及伤害安装使用人员，不得有漏纬，脏污痕迹。   5.1.3  套管的切口应光滑，无毛刺、散边。 项目　要求 低温柔韧性　无开裂、明显变色等外观不良 长期热老化　无开裂等外观不良、颜色可识别 短期热老化　无开裂等外观不良、颜色可识别 耐磨性　＞2000次 阻燃性　用于高压线束：V0阻燃等级 　用于低压线束：燃烧速率小于102mm/min   抗湿热老化性　无开裂、发白、脏污，颜色可识别 耐液体　无开裂、发白、变色、脏污，颜色可识别 禁用物质　铅、汞、六价铬、多溴联苯(PBBs)、多溴二苯醚(PBDEs)的质量百分数不得超过0.1%，镉的质量百分数不得超过0.01%。

Self-rolling protective sleeves for wiring harnesses Part 1: New energy vehicles

DB13/T 5567-2022 排吸工程用增强橡胶软管连接通用技术要求

General technical requirements for reinforced rubber hose connections for exhaust and suction projects

ISO 4671:2022 橡胶和塑料软管及软管组件.软管尺寸和软管组件长度的测量方法

This document specifies methods of measuring the inside diameter, outside diameter (including diameter over reinforcement of hydraulic hoses), wall thickness, concentricity and lining and cover thickness of hoses, methods of measurement and identification of the lengths of hoses and hose assemblies, and a method of verifying the through-bore of hydraulic hose assemblies.

Rubber and plastics hoses and hose assemblies — Methods of measurement of the dimensions of hoses and the lengths of hose assemblies

BS ISO 27126:2021 用于传输碳氢化合物、溶剂和化学品的热塑性多层（非硫化）软管和软管组件 规格

1   Scope This document specifies requirements for four types of thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for carrying hydrocarbons, solvents and chemicals. It specifies bore sizes from 25 mm to 300 mm, working pressures from 0,4 MPa (4 bar) to 1,4 MPa (14 bar) and working temperatures from −30 °C to 150 °C, according to type. Type 1 hoses are suitable for vapour applications. Types 2 to 4 hoses are suitable for liquid applications. NOTE 1 See Annex A concerning the selection of the material for the inner wall of layers and any polymeric coating of the internal wire helix related to the chemical(s) to be conveyed by the hoses and/or hose assemblies. NOTE 2 It is intended that the manufacturer be consulted where a polymeric coated internal wire is being considered for use with low conductivity hydrocarbons or chemicals. This document does not apply to hoses and hose assemblies for: — aircraft refuelling (see ISO 1825); — fuel dispensing (see ISO 5772); ...

Thermoplastic multi-layer (nonvulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals. Specification

ISO 9528:2022 航空航天.204°C/21 000 kPa级标准重量聚四氟乙烯（PTFE）软管组件.采购规范

Aerospace — Standard-weight polytetrafluoroethylene (PTFE) hose assemblies, classification 204 °C/21 000 kPa — Procurement specification

ISO 9938:2022 航空航天.204°C/28 000 kPa级聚四氟乙烯（PTFE）软管组件.采购规范

Aerospace — Polytetrafluoroethylene (PTFE) hose assemblies, classification 204 °C/28 000 kPa — Procurement specification

ISO 27127:2021 液化石油气和液化天然气输送用热塑性多层（非硫化）软管和软管组件.规范

This document specifies requirements for two types of thermoplastic multi-layer (non-vulcanized) transfer hoses and hose assemblies for carrying liquefied petroleum gas and liquefied natural gas. Each type is subdivided into two classes, one for onshore duties, and the other for offshore. — Class A hose is for use onshore. — Class B hose is for use offshore. This document is applicable for hose sizes from 25 mm to 250 mm, working pressures from 10,5 bar to 25 bar and operating temperatures from −196 °C to +45 °C, according to class. NOTE Offshore liquefied natural gas (LNG) hose assemblies are also specified in EN 1474-2. EN 1474-2 does not only specify offshore use, but also ship to shore and other LNG transfer applications.

Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas — Specification

ISO 27126:2021 烃类, 溶剂和化学品输送用热塑性多层 (非硫化) 塑料软管和软管组件. 规格

This document specifies requirements for four types of thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for carrying hydrocarbons, solvents and chemicals. It specifies bore sizes from 25 mm to 300 mm, working pressures from 0,4 MPa (4 bar) to 1,4 MPa (14 bar) and working temperatures from −30 °C to 150 °C, according to type. Type 1 hoses are suitable for vapour applications. Types 2 to 4 hoses are suitable for liquid applications. NOTE 1 See Annex A concerning the selection of the material for the inner wall of layers and any polymeric coating of the internal wire helix related to the chemical(s) to be conveyed by the hoses and/or hose assemblies. NOTE 2 It is intended that the manufacturer be consulted where a polymeric coated internal wire is being considered for use with low conductivity hydrocarbons or chemicals. This document does not apply to hoses and hose assemblies for: — aircraft refuelling (see ISO 1825); — fuel dispensing (see ISO 5772); — oil burners (see ISO 6806); — liquefied petroleum gas and liquefied natural gas (see ISO 27127); — fire fighting (see ISO 14557); — offshore liquefied natural gas (see EN 1474-2); — refrigeration circuits.

Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals - Specification

KS M 6702-2021 用于气体传输应用的橡胶管

Rubber tubings for gas transfer application

ISO 2929:2021 卡车散装燃料输送用橡胶软管和软管组件.规范

This document specifies the requirements for two groups of rubber hoses and rubber hose assemblies for loading and discharge of liquid hydrocarbon fuels with a maximum working pressure of 1,0 MPa (10 bar). Both groups of hoses are designed for a) use with hydrocarbon fuels having an aromatic-hydrocarbon content not exceeding 50 % by volume and containing up to 15 % of oxygenated compounds, and b) operation within the temperature range of −30 °C to +70 °C, undamaged by climatic conditions of −50 °C to +70 °C when stored in static conditions. NOTE Hoses for use at temperatures lower than −30 °C can be the subject of discussion between manufacturer and end user. This document is not applicable to hoses and hose assemblies for LPG systems, aviation fuel systems, fuel station systems or marine applications.

Rubber hoses and hose assemblies for bulk fuel delivery by truck — Specification

LST EN ISO 14557:2021 消防软管 橡胶和塑料吸入软管和软管组件（ISO 14557:2021）

Fire-fighting hoses - Rubber and plastics suction hoses and hose assemblies (ISO 14557:2021)

GSO ISO 6806:2021 燃油燃烧器用橡胶软管和软管组件 规范

ISO 6806:2017 specifies the minimum requirements for rubber hoses and hose assemblies for use in oil burners. The following two types of hose assembly are specified. - Type 1: Hose assemblies for flux and reflux, but not for insertion between the oil burner pump and the atomizing connection; maximum working pressure 1,0 MPa (10 bar); maximum oil temperature 100 °C. - Type 2: Hose assemblies for insertion between the oil burner pump and the atomizing connection; maximum working pressure 4,0 MPa (40 bar); maximum oil temperature 100 °C. The hose assemblies specified in this document are not intended to be used, without special assessment, for purposes other than oil burner installations.

Rubber hoses and hose assemblies for use in oil burners — Specification

GSO ISO 3949:2021 塑料软管和软管组件 液压应用用织物增强型 规范

This document specifies requirements for three types of textile-reinforced thermoplastics hose and hose assembly of nominal size from 3,2 to 25. Each type is divided into two classes dependent on electrical conductivity requirements. They are suitable for use with: — oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743‑4 at temperatures ranging from −40 °C to +93 °C; — water-based fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743‑4 at temperatures ranging from 0 °C to +60 °C — water at temperatures ranging from 0 °C to +60 °C. This document does not include requirements for end fittings. It is limited to the performance of hoses and hose assemblies. NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish the compatibility of the hose with the fluid to be used.

Plastics hoses and hose assemblies — Textile-reinforced types for hydraulic applications — Specification

T/CSTM 00246-2021 钢质管道内衬用承压复合软管及 施工技术规范

本文件规定了钢质管道用承压复合软管（以下简称“软管”）的产品分类、技术要求、试验方法、检验规则、标志、包装、运输、贮存、质量验收以及施工作业的要求。 本文件适用于已建金属管道的内衬修复及新建管道内衬防腐。软管适用于成品油、供热水的管道内衬，以及集油、掺水、注水、注聚合物等领域。本文件适用的管径范围为DN65~DN800，超出此范围可参照本文件执行。

Specification of pressure bearing composite hose and lining construction for steel pipeline

EC 1-2021 UNI EN ISO 3949:2021 塑料软管和软管组件 液压应用的织物增强型 规范

Plastics hoses and hose assemblies - Textile-reinforced types for hydraulic applications - Specification

ISO 14557:2021 消防软管 - 橡胶和塑料抽吸软管和软管组件

This document establishes the requirements and test methods for rubber and plastics suction hoses for fire-fighting purposes. These hoses can also be used manually to supply unpressurized water to the pump or for water discharge. NOTE All pressures are expressed in megapascals and in bar (1 MPa = 10 bar). Additional requirements are specified for hose assemblies, that is, hoses with couplings already fitted, where this is carried out by the hose manufacturer (see Clause 8). Type A (rubber) hoses are intended for use at a minimum temperature of −20 °C and Type B (thermoplastics) hoses are intended for use at a minimum temperature of −10 °C.

Fire-fighting hoses — Rubber and plastics suction hoses and hose assemblies

LST EN ISO 3861:2021 喷砂和喷砂用橡胶软管和软管组件 规范（ISO 3861:2021）

Rubber hoses and hose assemblies for sand and grit blasting - Specification (ISO 3861:2021)

T/CRIA 15002-2021 耐化学品流体软管

4.分类与结构 4.1分类 4.2 结构 5.材料性能要求 6.成品性能要求 7.检验规则 8.标志、包装、运输和储存

Chemical Resistant Fluid Hose

T/ZZB 2071-2021 农业喷雾用聚氯乙烯（PVC）软管

本文件规定了农业喷雾用聚氯乙烯（PVC）软管的产品分类、产品结构、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本文件适用于工作温度范围0 ℃～50 ℃，公称内径不大于13 mm、最大工作压力不大于6.0 MPa，供农药和（或）化肥制品加压喷雾用的聚氯乙烯软管（以下简称“软管”）。

Polyvinyl chloride(PVC) hoses for agricultural spraying