共找到 252 条与 软管 相关的标准,共 17 页
Rubber tubes for gas (Amendment 1)
Wire reinforced rubber hoses and hose assemblies for gas (Amendment 1)
Textile.reinforced hydraulic rubber hoses
이 표준은 광물성 작동유 또는 수성계 작동유1)를 사용하는 액압 장치 및 액압 회로에 사용
Wire reinforced rubber hose assemblies for hydraulic use
Rubber tubing and hoses for fuel circuits for internal-combustion engines-Specification-Part 3:Oxidized fuels
End fittings and adapters for hydraulic hose assemblies (Amendment 1)
Hose assemblies for liquefied petroleum gas (Amendment 2)
This translation has been made based on the Amendment to the origi- nal Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee as the result of proposal for revision of Japanese Industrial Standard with the draft being attached, based on the provi- sion of Article 12 Clause 1 of the Industrial Standardization Law ap- plicable to the case of revision by the provision of Article 14. Consequently, JIS S 2146:1991 is partially replaced with this Amend- ment.
Rubber tubes and polyvinyl chloride hoses with both end convenient joints for gas (Amendment 1)
이 표준은 용접 장치, 절단 장치 및 그 관련 설비에 부착되어 -20∼+70 ℃의 온도 범
Rubber hoses for welding, cutting and allied equipment
Rubber hoses and tubing for coolpng systems for pnternal.combustion engpnes
이 표준은 대기 온도와 대기압에서 액체로 존재하는 석유계 제품을 운송하는 선박의 부두에서
Rubber hoses and hose assemblies-Part 1:On-shore oil suction and discharge-Specification
Rubber hoses and hose assemblies-Part 1:On-shore oil suction and discharge-Specification
The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at http://assist.daps.dla.mil/.
BELT, AIRCRAFT SAFETY, CREWMAN'S
MIL-PRF-49450B, dated 06 March 2002, has been reviewed and determined to be valid for use in acquisition.
BATTERY, RECHARGEABLE, NICKEL-CADMIUM, VENTED, AIRCRAFT
本标准规定了应急消防用轴卷半硬性软管的性能和试验。内径为19mm和25mm的软管预定最大工作压力为1.2MPa,内径为 33mm 的软管预定最大工作压力为0.7MPa 。 符合本标准的软管可用在远距离使用场地之间,例如在建筑物群或其他建筑工地中的固定的消防软管卷轴上。对于内径为19mm和25mm的软管,最小卷轴直径为200mm,对于内径为33mm的软 管,最小卷轴直径为280mm。 本标准仅适用于在温度范围为-20℃ ~+60 ℃的非腐蚀性环境条件下使用的软管。 在购货方需要时,可以提供低于-20℃(例如-30℃)下使用的软管。
Rubber and plastics hoses, non-collapsible, for fire-fighting service Part 1: Semi-rigid reel hose for fixed first-aid installations
MIL-H-8810B, dated 28 September 1999, remains inactive for new design; however, the document is valid for use.
HANDLES, CONTROL, AIRCRAFT
この規格は,圧力3.3 kPa以下の都市ガス() 及び液化石油ガス() のガス栓とガス燃焼機器との間を連結するガス用強化ゴムホース(以下,ホースという。)及びホースアセンブリについて規定する。
Wire reinforced rubber hoses and hose assemblies for gas
JIS B 8261:1995を,次のように改正する。
Hose assemblies for liquefied petroleum gas (Amendment 1)
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号