83.140.40 软管 标准查询与下载
共找到 252 条与 软管 相关的标准，共 17 页
This International Standard specifies the dimensions and construction of, and requirements for, four types of hose and hose assembly for use in all operations associated with the ground fuelling and defuelling of aircraft. All four types are designed for a) use with petroleum fuels having an aromatic-hydrocarbon content not exceeding 30 % by volume; b) operation within the temperature range of −30 °C to +65 °C and such that they will be undamaged by climatic conditions of −40 °C to +70 °C when stored in static conditions; c) operation at up to 2,0 MPa (20 bar) maximum working pressure, including surges of pressure which the hose can be subjected to in service. NOTE 1 Type C hoses are intended for general pressure applications on all vehicles used for plane fuelling. They can also be used for vehicle/rail car loading and discharge where excessive vacuum does not occur. NOTE 2 Type F hoses can be used for plane delivery applications on vehicles that are also used for defuelling at high flow rates where type C hoses are not suitable. NOTE 3 Type E and F hoses can also be used for vehicle/rail car loading and discharge, for trailer to fueller transfer and for elevation platform supply (riser) to provide greater kink resistance.
Rubber hoses and hose assemblies for aircraft ground fuelling and defuelling -- Specification
- ICS
- 83.140.40
- CCS
- 发布
- 2015-09-03
- 实施
This International Standard specifies the requirements for three types of rubber or plastics inlet hoses and hose assemblies for washing-machines and dishwashers connected to the domestic water supply at a pressure not exceeding 1 MPa (10 bar). It is applicable to the following types of hose: — Type 1: rubber hoses for unheated water supply (maximum temperature 70 °C). — Type 2: rubber hoses for heated water supply (maximum temperature 90 °C). — Type 3: plastics hoses for unheated water supply (maximum temperature 60 °C). There may be national requirements for hose fittings and hoses conveying drinking water which must be complied with.
Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers -- Specification
- ICS
- 83.140.40
- CCS
- 发布
- 2015-09-03
- 实施
This International Standard specifies the requirements for two types of polymer-reinforced thermoplastics hose and hose assembly for suction and discharge applications with kerosene, heating oil, diesel fuel, and lubricating oils in the temperature range –10 °C to +45 °C. NOTE The hoses can be stored in a static condition at –30 °C to +65 °C without damage by climatic conditions.
Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids -- Specification
- ICS
- 83.140.40
- CCS
- 发布
- 2015-09-03
- 实施
This International Standard specifies requirements for rubber hoses and rubber hose assemblies used for the transfer of liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas and designed for use at working pressures ranging from vacuum to a maximum of 25 bar (2,5 MPa) within the temperature range −30 °C to +70 °C or, for low-temperature hoses (designated -LT), within the temperature range −50 °C to +70 °C.
Rubber hoses and hose assemblies for liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas up to 25 bar (2,5 MPa) -- Specification
- ICS
- 83.140.40
- CCS
- 发布
- 2015-09-03
- 实施
This International Standard specifies the requirements for three types of rubber hose and hose assembly used for measured fuel dispensing, including oxygenated fuels (up to a maximum of 15 % oxygenated compounds). The three types of hose are as follows: a) type 1: hoses with textile reinforcement suitable for reeling on a drum or hanging in bends; b) type 2: hoses with textile and helical wire reinforcement designed for torsional flexibility, suitable for coiling, reeling on a drum or hanging in bends; c) type 3: hoses with fine wire reinforcement designed for low dilation, suitable for reeling on a drum or hanging in bends.
Rubber hoses and hose assemblies for measured fuel dispensing -- Specification
- ICS
- 83.140.40
- CCS
- 发布
- 2015-09-03
- 实施
Le présent document corrige la Figure C.2 qui illustre un exemple de montage d'essai de traction.
Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification - Amendment 1
- ICS
- 83.140.40
- CCS
- G42
- 发布
- 2015-04-11
- 实施
- 2015-04-11
Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification (Incorporates Amendment A1: 2015)
- ICS
- 83.140.40
- CCS
- G33
- 发布
- 2015-02-01
- 实施
本标准规定了石化炼油延迟装备中水力除焦橡胶软管及软管组合件的型别，结构，尺寸及公差，要求，试验频次，标志，包装、贮存与运输及安装。 本标准适用于在-20 ℃～+80 ℃环境温度下使用的无井架或有井架水力除焦橡胶软管及软管组合件。
Rubber hoses and hose assemblies for removal of coke by water jetting
- ICS
- 83.140.40
- CCS
- G42
- 发布
- 2014-12-31
- 实施
- 2015-06-01
Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals. Specification
- ICS
- 83.140.40
- CCS
- G33
- 发布
- 2014-09-30
- 实施
- 2014-09-30
本标准规定了耐稀酸碱橡胶软管的产品分类、尺寸及公差、技术要求、试验频次、标志和包装、运输与贮存。本标准适用于-20 ℃~45 ℃环境中输送浓度不高于40 %的硫酸溶液及浓度不高于15 %的氢氧化钠溶液以及与上述浓度程度相当的酸碱溶液(硝酸除外)的橡胶软管(以下简称软管)。
Dilute acid and alkali resistant rubber hose
- ICS
- 83.140.40
- CCS
- G42
- 发布
- 2014-05-12
- 实施
- 2014-10-01
Testing methods for rubber and plastics hoses and hose assemblies -- Part 3: Determination of resistance to vacuum
- ICS
- 83.140.40
- CCS
- G30
- 发布
- 2014-03-20
- 实施
Selang termoplastik elastomer untuk kompor gas LPG
- ICS
- 83.140.40
- CCS
- 发布
- 2014
- 实施
This International Standard specifies requirements for two types, seven classes and three grades of wire- or textile-reinforced dredging hoses with nominal sizes ranging from 100 to 1 200. Within each class, all grades and sizes have the same maximum working pressure. Such hoses are suitable for the delivery or suction of seawater or freshwater mixed with silt, sand, coral and small stones with a specific gravity in the range from 1,0 to 2,3 at ambient temperatures ranging from -10 °C to +40 °C. This International Standard covers two types of hose, as follows: — type 1: floating type, for delivery only, which includes flotation material to give the hose buoyancy; — type 2: submarine type for delivery and suction. This International Standard does not specify requirements concerning the service life of hoses or hose assemblies. Specifying such requirements is the responsibility of the customer, in consultation with the hose manufacturer
Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications -- Specification
- ICS
- 83.140.40
- CCS
- 发布
- 2013-12-31
- 实施
Rubber hoses and rubber hose assemblies for liquefied petroleum gas (lpg)
- ICS
- 83.140.40
- CCS
- 发布
- 2013-03-13
- 实施
이 표준은 공칭 크기가 100∼1 200인 와이어 또는 직물로 강화된 준설용 호스의 두 가
Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications－Specification
- ICS
- 83.140.40
- CCS
- G42
- 发布
- 2012-11-30
- 实施
- 2012-11-30
This Standard specifies requirements for eight classes, three grades and six types of wire or textile reinforced dredging hose sizes ranging from 100 to 1 100. Each class has a single maximum working pressure for all sizes. They are suitable for use to tr
Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification
- ICS
- 83.140.40
- CCS
- 发布
- 2012-05-25
- 实施
- 2012-05-25
Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification (ISO 28017:2011)
- ICS
- 83.140.40
- CCS
- 发布
- 2012-02-29
- 实施
- 2012-02-29
이 표준은 도시가스에 사용하는 밸브와 연소 기구와의 사이 및 액화 석유 가스(이하 LPG라
Rubber tubings for gas transfer application
- ICS
- 83.140.40
- CCS
- G31
- 发布
- 2011-11-15
- 实施
- 2011-11-15
