C81 火警监视、报警与消防调度系统 标准查询与下载

ANSI/ISA 18.2-2009 加工工业报警系统的管理

1.1 General Applicability This standard addresses alarm systems for facilities in the process industries to improve safety, quality, and productivity. The general principles and processes in this standard are intended for use in the lifecycle management of an alarm system based on programmable electronic controller and computer based Human-Machine Interface (HMI) technology. Implementation of this standard should consider alarms from all systems presented to the operator, which may include basic process control systems, annunciator panels, safety instrumented systems, fire and gas systems, and emergency response systems.

Management of Alarm Systems for the Process Industries

ANSI/UL 268A-2009 烟道用烟雾探测器

Formalize requirements to insure consistent application for products submitted beyond the temperature range of 0 - 38 degrees C.

Smoke Detectors for Duct Application

ANSI/UL 268-2009 火灾报警信号系统烟雾探测器

Proposed Sixth Edition of UL 268, Smoke Detectors for Fire Alarm Systems, as a Binational Standard.

Smoke Detectors for Fire Alarm Signaling Systems

NF S61-932:2008 防火安全系统(FSS).防火系统用安装要求

Fire Safety Systems (FSS) - Installation rules for the fire protection system.

ISO 7240-28:2008 火灾探测和报警系统.第28部分:火灾探测控制设备

Fire detection and alarm systems - Part 28: Fire protection control equipment

NF C23-579-29-2:2008 易爆环境.第29-2部分:气体探测器.可燃气体探测器和氧气探测器的选择、安装、使用和维护

Explosive atmospheres - Part 29-2 : gas detectors - Selection, installation, use and maintenance of detectors for flammable gases and oxygen.

NF C23-579-29-1:2008 易爆环境.第29-1部分:气体探测器.可燃气体探测器的性能要求

Explosive atmospheres - Part 29-1 : gas detectors - Performance requirements of detectors for flammable gases.

BS EN 54-24:2008 火灾检测和报警系统.声音报警系统的组件.扩音器

Fire detection and fire alarm systems. Components of voice alarm systems. Loudspeakers

SANS 7240-16:2008 火灾探测及报警系统.第16部分:音响系统控制及指示设备

Specifies the requirements, test methods and performance criteria for sound system control and indicating equipment (s.s.c.i.e.) for use in buildings and structures as part of a sound system for emergency purposes (s.s.e.p.) (item C of Figure 2 in ISO 72

Fire detection and alarm systems Part 16: Sound system control and indicating equipment

SANS 7240-19:2008 火灾探测及报警系统.第19部分:紧急用途音响系统的设计、安装、调试及服务

Specifies the design, installation, commissionning and service requirements for a sound system for emergency purposes (s.s.e.p.; see ISO 7240-1:2005, Figure 1, item C), which is primarily intended to broadcast information for the protection of lives with

Fire detection and alarm systems Part 19: Design, installation, commissioning and service of sound systems for emergency purposes

DIN EN 54-24:2008 火灾检测和报警系统.第24部分:声音报警系统的组件.扩音器

This European Standard specifies requirements, test methods and performance criteria for loudspeakers intended to broadcast a warning of fire between a fire detection and fire alarm system and the occupants of a buildin9 This European Standard specifies loudspeakers for two types of application environment: type A, generally for indoor use and type B, generally for outdoor use. This European Standard does not cover loudspeakers for special applications, for example loudspeaker for use in hazardous applications, if such applications require additional or other requirements or tests than those 9iven in this European Standard. This European Standard is not intended to cover addressable loudspeakers, loudspeakers with active components. Voice alarm sounders are covered in EN 54-3:2001.

Fire detection and fire alarm systems - Part 24: Components of voice alarm systems - Loudspeakers; English version of DIN EN 54-24:2008-06

DIN EN 54-16:2008 火灾检测和火警系统.第16部分:声音报警控制和指示设备

This European Standard specifies requirements, methods of test and performance criteria for voice alarm control and indicating equipment for use in fire detection and fire alarm systems installed in buildings, where the alarm ,signal is in the form of tone(s) or voice message(s), or both. It also prowdes for the evaluation of conformity of the equipment to the requirements of this European Standard NOTE The overall requirements of a voice alarm system, especially concerning audibility and intelligibility, are not covered in this part of EN 54. The manufacturer should consider requirements of an overall system that may affect the equipment design. Such system requirements may be specified in another part of EN 54, in national legislation, codes and standards or in contractual documents.

Fire detection and fire alarm systems - Part 16: Voice alarm control and indicating equipment; English version of DIN EN 54-16:2008-06

GA 767-2008 消防控制室通用技术要求

本标准规定了消防控制室的一般要求、消防安全管理、控制和显示要求、信息记录要求、信息传输要求。 本标准适用于GB 50116中规定的集中火灾报警系统、控制中心报警系统中的消防控制室或消防控制中心。

General technical requirements of fire control center

BS EN 54-16:2008 火灾探测和火灾警报系统.声音报警控制和指示设备

This European Standard specifies requirements, methods of test and performance criteria for voice alarm control and indicating equipment for use in fire detection and fire alarm systems installed in buildings, where the alarm signal is in the form of tone(s) or voice message(s), or both. It also provides for the evaluation of conformity of the equipment to the requirements of this European Standard. NOTE The overall requirements of a voice alarm system, especially concerning audibility and intelligibility, are not covered in this part of EN 54. The manufacturer should consider requirements of an overall system that may affect the equipment design. Such system requirements may be specified in another part of EN 54, in national legislation, codes and standards or in contractual documents.

Fire detection and fire alarm systems. Voice alarm control and indicating equipment

BS EN 54-25:2008 火灾探测和火警系统.无线电连接件用组件

This European Standard specifies requirements, test methods and performance criteria for components used in fire alarms systems, installed in and around buildings, which use radio frequency links (RF links) to communicate. It also provides requirements for the evaluation of conformity of the components to the requirements of this European Standard. Where components work together and this requires knowledge of the system design, this document also specifies requirements on the system. When the fire detection and fire alarm systems (FDAS) use wired and RF links, the relevant parts of EN 54 apply together with this document. Requirements relevant to wire links are superseded or modified by those included in this European Standard. This document does not restrict:  the intended use of radio spectrum, e.g. frequency, power output of devices;  the allowed maximum number of the components using RF links within the FDAS or one transmission path and/or RF link;  the allowed maximum number of the components affected by loss of one transmission path and/or RF link. These requirements relate to national regulations and can vary from member state to member state.

Fire detection and fire alarm systems. Components using radio links

UL 1480 BULLETIN-2008 商用和专业用紧急火灾报警用扬声器UL安全性标准.评议提交截止日期:2008年5月2日

Speakers for indoor and/or outdoor use in dry, damp, wet, or underwater location and are intended for one or more of the following: Fire alarm systems providing emergency voice/alarm occupant notification; commercial and professional audio systems providing non-emergency sound reinforcement and reproduction (this includes equipment for institutional, industrial use); Non-fire emergency voice-warning systems; and underwater speakers.

UL Standard for Safety Speakers for Fire Alarm, Emergency, and Commercial and Professional Use COMMENTS DUE: May 2, 2008

UL 1981 BULLETIN-2008 中央工作站自动化系统UL安全性标准.评议提交截止日期:2008年5月2日

1.1 These requirements cover computerized central-station automation systems intended for use in central-station, proprietary, remote and subsidiary burglar-, and fire-alarm applications for the purpose of automating the signal handling and processing of change-of-status signals generated by receivers. In case of failure of an automation system, the receiving equipment is relied on for receiving and recording change-of-status signals and the provision of an audible and visual signal that identifies the source and type of signal that requires operator attention. These systems are intended to be installed in accordance with the following:a)The National Electrical Code, NFPA 70;b)The National Fire Alarm Code, NFPA 72; and c)The Standard for Central-Station Alarm Services, UL 827.1.2 A product that contains features, characteristics, components, materials, or systems new or different from those covered by the requirements in this standard, and that involves a risk of fire or of electric shock or injury to persons shall be evaluated using appropriate additional component and end-product requirements to maintain the level of safety as originally anticipated by the intent of this standard. A product whose features, characteristics, components, materials, or systems conflict with specific requirements or provisions of this standard does not comply with this standard. Revision of requirements shall be proposed and adopted in conformance with the methods employed for development, revision, and implementation of this standard.

UL Standard for Safety Central-Station Automation Systems COMMENTS DUE: May 2, 2008

CEN EN 54-25-2008_ 火灾探测和火警系统.第25部分:利用无线电连接的元件

This European Standard specifies requirements, test methods and performance criteria for components used in fire alarms systems, installed in and around buildings, which use radio frequency links (RF links) to communicate. It also provides requirements for the evaluation of conformity of the components to the requirements of this European Standard. Where components work together and this requires knowledge of the system design, this document also specifies requirements on the system. When the fire detection and fire alarm systems (FDAS) use wired and RF links, the relevant parts of EN 54 apply together with this document. Requirements relevant to wire links are superseded or modified by those included in this European Standard. This document does not restrict: ? the intended use of radio spectrum, e.g. frequency, power output of devices; ? the allowed maximum number of the components using RF links within the FDAS or one transmission path and/or RF link; ? the allowed maximum number of the components affected by loss of one transmission path and/or RF link. These requirements relate to national regulations and can vary from member state to member state.

Fire detection and fire alarm systems — Part 25: Components using radio links

BS EN 60079-29-2:2007 爆炸性气体环境.第29-2部分:气体探测器.易燃气体和氧用探测器的选择、安装、使用和维护

This part of IEC 60079-29 gives guidance on, and recommended practice for, the selection, installation, safe use and maintenance of electrically operated group II apparatus intended for use in industrial and commercial safety applications for the detection and measurement of flammable gases complying with the requirements of IEC 60079-29-1. This standard is applicable for oxygen measurement for the purpose of inertisation where explosion protection is provided by the exclusion of oxygen instead of measuring the combustible gases or vapours present. This standard is a compilation of practical knowledge to assist the user, and applies to apparatus, instruments and systems that indicate the presence of a flammable or potentially explosive mixture of gas or vapour with air by using an electrical signal from a gas sensor to produce a meter reading, to activate a visual or audible pre-set alarm or other device, or any combination of these. Such apparatus may be used as a means of reducing the risk whenever there is the possibility of a risk to life or property specifically due to the accumulation of a combustible gas-air mixture, by providing such warnings. It may also be used to initiate specific safety precautions (e.g. plant shutdown, evacuation, fire extinguishing procedures). This standard is applicable to all new permanent installations and, where reasonably practicable, to existing permanent installations. It is also applicable to temporary installations, whether new or existing. Similarly it is applicable to the safe use of portable or transportable apparatus, irrespective of the age or complexity of such apparatus. Since much modern apparatus of this type also includes oxygen deficiency detection and/or specific toxic gas sensors, some additional guidance is given for these topics. NOTE When in classified areas, the apparatus should be so installed and used that it is not capable of itself igniting a combustible gas-air mixture. It should therefore comply with the requirements of IEC 60079-10. For the purposes of this standard, except where specifically stated otherwise, flammable gases shall include flammable vapours. This standard applies only to group II apparatus (i.e. apparatus intended for use in industrial and commercial safety applications, involving areas classified in accordance with IEC 60079-10). For the purposes of this standard, apparatus includes a) fixed apparatus; b) transportable apparatus; and c) portable apparatus. This standard is not intended to cover, but may provide useful information, for the following: a) apparatus intended only for the detection of non-flammable toxic gases; b) apparatus of laboratory or scientific type intended only for analysis or measurement purposes; c) apparatus intended for underground mining applications (group I apparatus); d) apparatus intended only for process control applications; e) apparatus intended for applications in explosives processing and manufacture; f) apparatus intended for the detection of a potentially flammable atmosphere resulting from dust or mist in air; g) open path apparatus not used for point measurement.

Explosive atmospheres - Part 29-2: Gas detectors - Selection, installation, use and maintenance of detectors for flammable gases and oxygen

DIN 14661:2008 消防设备.火灾探测和报警系统用消防队控制面板

Firefighting equipment - Fire-brigade control panel for fire detection and fire alarm systems