E36 润滑脂 标准查询与下载

GB/T 7325-1987 润滑脂和润滑油蒸发损失测定法

本方法适用于测定润滑脂和润滑油的蒸发损失。这些润滑剂在使用时蒸发损失为一项重要因素。蒸发损失可以在99～150℃的任一温度下进行测定。

Petroleum products--Lubricating greases and oils--Determination of evaporation loss

GB 491-1987 钙基润滑脂

本标准适用于以动植物脂肪钙皂稠化矿物润滑油而制得的普通钙基润滑脂。 本产品适用于汽车、拖拉机、冶金、纺织等机械设备的润滑。使用温度范围为-10～60℃。

Calcium base grease

GB 7326-1987 润滑脂铜片腐蚀试验法

Copper strip corrosion test method for grease

GB/T 5018-1985 润滑脂防腐蚀性试验法

本方法适用于在潮湿情况下存放涂有润滑脂的锥形滚子轴承来测定润滑脂的防腐蚀性能。本方法是根据能表示试验室结果与用润滑脂润滑的飞机轮轴承使用结果的对应关系的CRC技术文件L41制订的。

Standard test method for corrosion preventive properties of lubricating greases

GB/T 3498-1983 润滑脂宽温度范围滴点测定法

本方法适用于测定润滑脂宽温度范围滴点。

Lubricating greases--Determination of dropping point(wide temperature range)

GB/T 392-1977 润滑脂压力分油测定法

本方法适用于测定润滑脂的分油量。 本方法是利用加压分油器将油从润滑脂内压出，然后测定压出的油量。

Determination of colloid-stability of lubricating greases

GB/T 513-1977 润滑脂机械杂质测定法(酸分解法)

本方法适用于测定润滑脂中不溶于盐酸、石油醚（溶剂汽油或苯）、乙醇-苯混合液及蒸馏水的机械杂质含量。也适用于测定特别加入润滑脂中而不溶于上述试剂的填充物含量。

Determination of mechanical impurities in lubricating greases(acid decomposition method)

GB 492-1989 钠基润滑脂

Sodium Grease

GB/T 512-1965 润滑脂水分测定法

本方法适用于测定润滑脂的水含量，测定结果用重量百分数表示。

Determination of water content in lubricating greases

NF T60-132:2020 石油产品和润滑剂. 润滑脂和矿脂锥入度的测定

Le présent document spécifie des méthodes destinées à une estimation empirique de la consistance des graisses lubrifiantes et des pétrolatums par détermination de la pénétrabilité d'un cône normalisé.

Petroleum products and lubricants - Determination of cone penetration of lubricating greases and petrolatum

NB/SH/T 0985-2019 工程机械用润滑脂

Grease for construction machinery

ASTM D1742-18 润滑脂贮存过程中油分离的标准试验方法

5.1 When a lubricating grease separates oil, the remaining composition increases in consistency. This can affect the ability of the product to function as designed. 5.2 It has been found that the results of this test correlate directly with the oil separation that occurs in 358201;lb pails of grease during storage. 5.3 This test method is not intended to predict oil separation tendencies of the grease under dynamic conditions. 1.1 This test method covers the determination of the tendency of a lubricating grease to separate oil during storage in both normally filled and partially filled containers. 1.2 This test method is not suitable for greases softer than NLGI No. 1 grade. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see 7.1. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Oil Separation from Lubricating Grease During Storage

SH/T 0948-2017 轧辊轴承润滑脂

Roller bearing grease

SH/T 0949-2017 彩棉机润滑脂

Color cotton machine grease

SN/T 4943-2017 食品级润滑油（脂）中多环芳烃的测定 气相色谱-质谱联用法?

Determination of polycyclic aromatic hydrocarbons in food-grade lubricants (greases) using gas chromatography-mass spectrometry?

BS EN 12081:2017 铁路应用 轴箱 润滑脂

Railway applications - Axleboxes - Lubricating greases

SN/T 4759-2017 进口食品级润滑油（脂）中锑、砷、镉、铅、汞、硒元素的测定方法 电感耦合等离子体质谱（ICP-MS）法

Determination method of antimony, arsenic, cadmium, lead, mercury and selenium in imported food grade lubricating oil (grease) Inductively coupled plasma mass spectrometry (ICP-MS)

DIN 51811:2017-05 润滑剂试验.润滑脂对铜腐蚀作用的试验.铜带去光泽试验

Testing of lubricants - Testing of corrosiveness to copper of greases - Copper strip tarnish test

DIN 51810-2:2017 润滑剂试验.润滑脂流变性能试验.第2部分: 采用带有平行板测量系统的震荡式流变仪的流点测定

Testing of lubricants - Testing rheological properties of lubricating greases - Part 2: Determination of flow point using an oscillatory rheometer with a parallel-plate measuring system

ASTM D566-17 润滑脂滴点的标准试验方法

5.1 In general, the dropping point is the temperature at which the grease passes from a semisolid to a liquid state under the conditions of test. This change in state is typical of greases containing as thickeners soaps of conventional types. Greases containing as thickeners materials other than conventional soaps can, without change in state, separate oil. This test method is useful to assist in identifying the grease as to type and for establishing and maintaining bench marks for quality control. The results are considered to have only limited significance with respect to service performance as dropping point is a static test. Note 1: Cooperative testing indicates that in general, dropping points by Test Method D5663 and Test Method D2265 are in agreement. In cases where results differ, there is no known significance. However, agreement between producer and consumer as to the test method used is advisable. 1.1 This test method covers the determination of the dropping point of lubricating grease. 1.2 This test method is not recommended for use at bath temperatures above 2888201;°C. For higher temperatures Test Method D2265 should be used. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 WARNING—This test method uses mercury-filled thermometers. Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for details and EPA’s website— http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. The responsible subcommittee, D02.G.3, continues to explore alternatives to eventually replace the mercury thermometers. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 6.4 and 8.1. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical ......

Standard Test Method for Dropping Point of Lubricating Grease