E90 石油勘探、开发、集输设备综合 标准查询与下载

BS EN ISO 10438-2:2008 石油、石化和天然气工业.润滑、轴封和控油系统及辅助设备.专用油系统

ISO 10438-2:2007, in conjunction with ISO 10438-1, specifies requirements for oil systems for special-purpose applications. These oil systems can provide lubrication oil, seal oil or both. These systems can serve equipment such as compressors, gears, pumps and drivers.

Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Special-purpose oil systems

BS EN ISO 10438-3:2008 石油、石化和天然气工业.润滑、轴封和控油系统及辅助设备.专用油系统

ISO 10438-3:2007, in conjunction with ISO 10438-1, specifies requirements for oil systems for general-purpose applications. These oil systems can provide lubrication oil, but not seal oil and can serve equipment such as compressors, gears, pumps and drivers.

Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - General-purpose oil systems

BS EN ISO 10438-4:2008 石油、石化和天然气工业.润滑、轴封、控油系统及辅助装置.自动气封支撑系统

ISO 10438-4:2007 in conjunction with ISO 10438-1 specifies requirements for support systems for self-acting gas seals (dry gas seals), for example as described in ISO 10439 and ISO 10440-1. These systems can serve equipment such as compressors, gears, pumps and drivers.

Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Self-acting gas seal support systems

BS EN ISO 10438-1:2007 石油,石化和天然气工业.润滑,轴封和控油系统及辅助设备.一般要求

ISO 10438-1:2007 specifies general requirements for lubrication systems, oil-type shaft-sealing systems, dry-gas face-type shaft-sealing systems and control-oil systems for general- or special-purpose applications. General-purpose applications are limited to lubrication systems. These systems can serve equipment such as compressors, gears, pumps and drivers. ISO 10438-1:2007 is intended to be used in conjunction with ISO 10438-2, ISO 10438-3 or ISO 10438-4, as appropriate.

Petroleum, petrochemical and natural gas industries - Lubrication , shaft-sealing and control-oil systems and auxiliaries - General requirements

ISO 19902:2007 石油和天然气工业.固定式海上钢结构

This International Standard specifies requirements and provides recommendations applicable to the following types of fixed steel offshore structures for the petroleum and natural gas industries: - caissons, free-standing and braced; - jackets; - monotowers; - towers. In addition, it is applicable to compliant bottom founded structures, steel gravity structures, jack-ups, other bottom founded structures and other structures related to offshore structures (such as underwater oil storage tanks, bridges and connecting structures), to the extent to which its requirements are relevant. This International Standard contains requirements for planning and engineering of the following tasks: a) design, fabrication, transportation and installation of new structures as well as their future removal; b) in-service inspection and integrity management of both new and existing structures; c) assessment of existing structures; d) evaluation of structures for reuse at different locations.

Petroleum and natural gas industries - Fixed steel offshore structures

KS B ISO 10426-3:2007 石油和天然气工业.油井固井用水泥和材料.第3部分:深水油井水泥成分的测试

이 규격은 심해 환경에서의 석유 및 천연가스 산업에 사용되는 유정 시멘트 및 시멘트 혼합물

Petroleum and natural gas industries－Cements and materials for well cementing－Part 3：Testing of deepwater well cement formulations

KS B ISO 10426-1:2007 石油和天然气工业.油井固井用水泥和材料.第1部分:规范

이 규격은 유정 시멘트 8종에 대한 각각의 화학적, 물리적 특성과 물리적 시험절차를 포함한

Petroleum and natural gas industries－Cements and materials for well cementing－Part 1：Specification

SY/T 6676-2007 钻井液密度计校准方法

本标准规定了钻井液密度计（以下简称密度计）的技术要求、校准条件、校准方法、校准结果处理和校准间隔。 本标准适用于新制造、使用中和修理后密度计的校准。

Calibration method of drilling fluid density meter

SY/T 6678-2007 电子示功仪校准方法

本标准规定了电子示功仪（以下简称示功仪）的技术要求、校准条件、校准项目和校准方法。 本标准适用于油田测试中新制造、使用中和修理后的示功仪的校准。

Calibration method of the electronic dynamometer

SY/T 6679.1-2007 综合录井仪校准方法 第1部分：传感器

本标准规定了综合录井仪中脉冲式绞车传感器、接近开关传感器、靶式流量传感器、压力传感器、霍尔效应扭矩传感器、电导率传感器、超声波式体积传感器、密度传感器、温度传感器、浮子式体积传感器、硫化氢传感器的技术要求及校准条件、项目、方法和结果处理。 本标准适用于新制造、使用中和修理后的综合录井仪中脉冲式绞车传感器、接近开关传感器、靶式流量传感器、压力传感器、霍尔效应扭矩传感器、电导率传感器、超声波式体积传感器、密度传感器、温度传感器、硫化氢传感器、浮子式体积传感器的校准。

Calibration method for mud. logging unit. Part 1: Sensors

SY/T 6675-2007 井下流量计校准方法

本标准规定了井下流量计的校准条件、校准项目和校准方法、校准结果及复校时间间隔等内容。 本标准适用于新制造、使用中和修理后井下流量计的校准。

Calibration method of the down hole flow meter gauge

SY/T 6476-2007 输送钢管落锤撕裂试验方法

本标准规定了输送钢管落锤撕裂试验的定义和符号、试验设备、试样、试样的试验、试样的评定和试验报告等内容。 本标准适用于输送钢管和制管用钢板、板卷的落锤撕裂试验和结果评定。

Practice for drop-weight tear tests on steel line pipe

DIN EN ISO 10441:2007 石油、石化和天然气工业.机械动力传输用挠性接箍.特殊应用(ISO 10441-2007)

This International Standard specifies the requirements for couplings for the transmission of power between the rotating shafts of two machines in special—purpose applications in the petroleum，petrochemical and natural gas industries．Such applications are typically in large and／or high speed machines，in services that can be required to operate continuously for extended periods，are often unspared and are critical to the continued operation of the installation.By agreement，it can be used for other applications or sewices． Couplings covered by this International Standard are designed to accommodate parallel(or lateral)offset， angular misalignment and axial displacement of the shafts without imposing unacceptable mechanical loading on the coupled machines．It is applicable to gear，metallic flexible element，quill shaft and torsionally resilient type couplings．Tomional damping and resilient type couplings are detailed in Annex A;gear-type couplings are detailed in Annex B and quill shaft style couplings are detailed in Annex C． This International Standard covers the design，materials of construction，manufacturing quality，inspection and testing of special—purpose couplings． This International Standard does not define criteria for the selection of coupling types for specific applications. This International Standard is not applicable to other types of couplings，such as clutch，hydraulic，eddy— current，rigid，radial spline，chain and bellows types．

Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - Special-purpose applications (ISO 10441:2007); English version EN ISO 10441:2007

DIN EN ISO 14224:2007 石油、石化和天然气工业.设备可靠性和维修数据的采集与交换

This International Standard provides a comprehensive basis for the collection of reliability and maintenance (RM) data in a standard format for equipment in all facilities and operations within the petroleum, natural gas and petrochemical industries during the operational life cycle of equipment. It describes data-collection principles and associated terms and definitions that constitute a "reliability language" that can be useful for communicating operational experience. The failure modes defined in the normative part of this International Standard can be used as a "reliability thesaurus" for various quantitative as well as qualitative applications. This International Standard also describes data quality control and assurance practices to provide guidance for the user. Standardization of data-collection practices facilitates the exchange of information between parties, e.g. plants, owners, manufacturers and contractors. This International Standard establishes requirements that any in-house or commercially available RM data system is required to meet when designed for RM data exchange. Examples, guidelines and principles for the exchange and merging of such RM data are addressed. Annex A contains a summary of equipment that this International Standard covers. • This International Standard recommends a minimum amount of data that is required to be collected and it focuses on two main issues: — data requirements for the type of data to be collected for use in various analysis methodologies; — standardized data format to facilitate the exchange of reliability and maintenance data between plants, owners, manufacturers and contractors. • The following main categories of data are to be collected: — equipment data, e.g. equipment taxonomy, equipment attributes; — failure data, e.g. failure cause, failure consequence; — maintenance data, e.g. maintenance action, resources used, maintenance consequence, down time. NOTE Clause 9 gives further details on data content and data format. • The main areas where such data are used are the following: — reliability, e.g. failure events and failure mechanisms; — availability/efficiency, e.g. equipment availability, system availability, plant production availability; — maintenance, e.g. corrective and preventive maintenance, maintenance supportability; — safety and environment, e.g. equipment failures with adverse consequences for safety and/or environment. This International Standard does not apply to the following: — data on (direct) cost issues; — data from laboratory testing and manufacturing (e.g. accelerated lifetime testing); — complete equipment data sheets (only data seen relevant for assessing the reliability performance are included); — additional on-service data that an operator, on an individual basis, can consider useful for operation and maintenance; — methods for analysing and applying RM data (however, principles for how to calculate some basic reliability and maintenance parameters are included in the annexes).

Petroleum, petrochemical and natural gas industries - Collection and exchange of reliability and maintenance data for equipment (ISO 14224:2006); English version EN ISO 14224:2006

DIN EN ISO 19903:2007 石油和天然气工业.固定混凝土海上平台

This International Standard specifies requirements and provides recommendations applicable to fixed concrete offshore structures for the petroleum and natural gas industries, and specifically addresses a) the design, construction, transportation and installation of new structures, including requirements for in-service inspection and possible removal of structures, b) the assessment of structures in service, and c) the assessment of structures for reuse at other locations. This International Standard is intended to cover the engineering processes needed for the major engineering disciplines to establish a facility for offshore operation. It can also be used for the design of floating concrete structures as specified in ISO 19904-1 i11] (and the future ISO 19904-2 I12] when published) and for arctic structures (as specified in the future ISO 19906 I7! when published). In order to provide a standard that will be useful to the industry, a comprehensive treatment of some topics is provided where there is currently no relevant reference. For such well-known topics as the design formulas for concrete structural members, this International Standard is intended to be used in conjunction with a suitable reference standard for basic concrete design (see 8.2.1). The designer can use suitable national or regional design standards that provide the required level of safety. Only other ISO documents will be referenced directly in the text.

Petroleum and natural gas industries - Fixed concrete offshore structures (ISO 19903:2006); English version EN ISO 19903:2006

DIN EN ISO 14692-2 Berichtigung 1:2007 石油和天然气工业.玻璃纤维增强塑料.第2部分:生产资格

This part of ISO 14692 defines requirements for the qualification and manufacture of GRP piping and fittings.

Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture (ISO 14692-2:2002); English version EN ISO 14692-2:2002, Corrigenda to DIN EN ISO 14692-2:2005-07; English version EN ISO 14692-2:2002/AC

ISO 16812:2007 石油、石化和天然气工业.壳管式热交换器

This International Standard specifies requirements and gives recommendations for the mechanical design, material selection, fabrication, inspection, testing and preparation for shipment of shell-and-tube heat exchangers for the petroleum, petrochemical and natural gas industries. This International Standard is applicable to the following types of shell-and-tube heat exchangers: heaters, condensers, coolers and reboilers. This International Standard is not applicable to vacuum-operated steam surface condensers and feed-water heaters.

Petroleum, petrochemical and natural gas industries - Shell-and-tube heat exchangers

DIN EN ISO 13503-4:2007 石油和天然气工业.完井液和材料.第4部分:增产液和砾石填充液静态渗漏测量程序

This International Standard contains procedure for measuring stimulation and gravelpack fluid leakoff under static conditions.

Petroleum and natural gas industries - Completion fluids and materials - Part 4: Procedure for measuring stimulation and gravel-pack fluid leakoff under static conditions (ISO 13503-4:2006); English version EN ISO 13503-4:2006

BS ISO 19903:2007 石油和天然气工业.固定混凝土海上平台

ISO 19903:2006 specifies requirements and provides recommendations applicable to fixed concrete offshore structures for the petroleum and natural gas industries, and specifically addresses the design, construction, transportation and installation of new structures, including requirements for in-service inspection and possible removal of structures, the assessment of structures in service, and the assessment of structures for reuse at other locations.

Petroleum and natural gas industries - Fixed concrete offshore structures

ASTM F2067-07 溢油弹道模型开发和使用的标准实施规程

During an oil-spill response, trajectory models are used to predict the future movement and fate of oil (forecast mode). This information is used for planning purposes to position equipment and response personnel in order to optimize a spill response. Oil-spill trajectory models can be used in a statistical manner (stochastic mode) to identify the areas that may be impacted by oil spills. In those cases where the degree of risk at various locations from an unknown source is needed, trajectory models can be used in an inverse mode to identify possible sources of the pollution (receptor mode). Oil-spill trajectory models are used in the development of scenarios for training and exercises. The use of models allows the scenario designer to develop incidents and situations in a realistic manner.1.1 This practice describes the features and processes that should be included in an oil-spill trajectory and fate model.1.2 This practice applies only to oil-spill models and does not consider the broader need for models in other fields. This practice considers only computer-based models, and not physical modeling of oil-spill processes.1.3 This practice is applicable to all types of oil in oceans, lakes, and rivers under a variety of environmental and geographical conditions.1.4 This practice does not address issues of computer operation. It is assumed that the user of this practice is familiar with the use of a computer and its operating systems.

Standard Practice for Development and Use of Oil-Spill Trajectory Models