E90 石油勘探、开发、集输设备综合 标准查询与下载

SY/T 6757-2009 井下压力计检定装置校准方法

本标准规定了井下压力计检定装置的技术要求、校准条件、校准项目和校准方法。 本标准适用于新制造、使用中和修理后井下压力计检定装置(以压力传感器为主标准器)的校准。本标准不适用于以活塞压力计为主标准器的井下压力计检定装置的校准。

Calibration method of the verification device for downhole pressure gauge

SY/T 6679.3-2009 综合录井仪校准方法.第3部分:数据釆集系统

SY/T 6679的本部分规定了综合录井仪数据采集系统的技术要求及校准条件、校准项目、校准方法、校准处理和校准间隔。 本部分适用于新制造、使用中和修理后的数据采集系统校准。

Calibration method of mud logging unit.Part 3:Data acquisition system

SY/T 6758-2009 岩性密度测井仪校准方法

本标准规定了岩性密度测井仪校准的技术要求、校准设备、校准条件、校准方法和复校时间间隔。 本标准适用于新投产、使用中和维修后的岩性密度仪的校准。

Calibration method of lithological density log tool

SY/T 6759-2009 示功仪校准装置校准方法

本标准规定了示功仪校准装置的计量特性、校准条件、校准项目和校准方法。 本标准适用于新制造、使用中和维修后的示功仪校准装置的校准。

Calibration method of the calibration device for indicator

ISO 19901-6:2009 石油和天然气工业.海上建筑物的详细要求.第6部分:船舶管理

Petroleum and natural gas industries - Specific requirements for offshore structures - Part 6: Marine operations

BS EN ISO 15156-1:2009 石油和天然气工业.油、气生产中含硫化氢(H2S)环境下使用的材料.耐裂化材料选择的一般原则

This part of ISO 15156 describes general principles and gives requirements and recommendations for the selection and qualification of metallic materials for service in equipment used in oil and gas production and in natural-gas sweetening plants in H2S-containing environments, where the failure of such equipment can pose a risk to the health and safety of the public and personnel or to the environment. It can be applied to help to avoid costly corrosion damage to the equipment itself. It supplements, but does not replace, the materials requirements given in the appropriate design codes, standards or regulations. This part of ISO 15156 addresses all mechanisms of cracking that can be caused by HS, including sulfide stress cracking, stress corrosion cracking, hydrogen-induced cracking and stepwise cracking, stress-oriented hydrogen-induced cracking, soft zone cracking and galvanically induced hydrogen stress cracking. Table 1 provides a non-exhaustive list of equipment to which this part of ISO 15156 is applicable, including permitted exclusions. This part of ISO 15156 applies to the qualification and selection of materials for equipment designed and constructed using conventional elastic design criteria. This part of ISO 15156 is not necessarily applicable to equipment used in refining or downstream processes and equipment.

Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - General principles for selection of cracking-resistant materials

BS EN ISO 15156-2:2009 石油、石化和天然气工业.油、气生产中含硫化氢(H2S)环境下使用的材料.耐裂化碳和低合金钢及铸铁的使用

This part of ISO 15156 gives requirements and recommendations for the selection and qualification of carbon and low-alloy steels for service in equipment used in oil and natural gas production and natural gas treatment plants in HS-containing environments, whose failure can pose a risk to the health and safety of the public and personnel or to the environment. It can be applied to help to avoid costly corrosion damage to the equipment itself. It supplements, but does not replace, the materials requirements of the appropriate design codes, standards or regulations. This part of ISO 15156 addresses the resistance of these steels to damage that can be caused by sulfide stress-cracking (SSC) and the related phenomena of stress-oriented hydrogen-induced cracking (SOHIC) and soft-zone cracking (SZC). This part of ISO 15156 also addresses the resistance of these steels to hydrogen-induced cracking (HIC) and its possible development into stepwise cracking (SWC). This part of ISO 15156 is concerned only with cracking. Loss of material by general (mass loss) or localized corrosion is not addressed. Table 1 provides a non-exhaustive list of equipment to which this part of ISO 15156 is applicable, including permitted exclusions. This part of ISO 15156 applies to the qualification and selection of materials for equipment designed and constructed using conventional elastic design criteria. For designs utilizing plastic criteria (e.g. strain-based and limit-state designs), see ISO 15156-1:2009, Clause 5. Annex A lists SSC-resistant carbon and low alloy steels, and A.2.4 includes requirements for the use of cast irons. This part of ISO 15156 is not necessarily suitable for application to equipment used in refining or downstream processes and equipment.

Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Cracking-resistant carbon and low-alloy steels, and the use of cast irons

BS EN ISO 15156-3:2009 石油、石化和天然气工业.油、气生产中含硫化氢(H2S)环境下使用的材料.耐裂化CRAs(耐腐蚀合金)和其他合金

This part of ISO 15156 gives requirements and recommendations for the selection and qualification of CRAs (corrosion-resistant alloys) and other alloys for service in equipment used in oil and natural gas production and natural gas treatment plants in H2S-containing environments, whose failure can pose a risk to the health and safety of the public and personnel or to the environment. It can be applied to help to avoid costly corrosion damage to the equipment itself. It supplements, but does not replace, the materials requirements of the appropriate design codes, standards or regulations. This part of ISO 15156 addresses the resistance of these materials to damage that can be caused by sulfide stress-cracking (SSC), stress-corrosion cracking (SCC) and galvanically-induced hydrogen stress cracking (GHSC). This part of ISO 15156 is concerned only with cracking. Loss of material by general (mass loss) or localized corrosion is not addressed. Table 1 provides a non-exhaustive list of equipment to which this part of ISO 15156 is applicable, including permitted exclusions. This part of ISO 15156 applies to the qualification and selection of materials for equipment designed and constructed using conventional elastic design criteria. For designs utilizing plastic criteria (e.g. strain-based and limit-state designs), see ISO 15156-1:2009, Clause 5. This part of ISO 15156 is not necessarily suitable for application to equipment used in refining or downstream processes and equipment.

Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys

ISO 15156-1:2009 石油和天然气工业.油、气生产中含硫化氢(H2S)环境下使用的材料.第1部分:耐裂化材料选择的一般原则

Petroleum and natural gas industries - Materials for use in H₂S-containing environments in oil and gas production - Part 1: General principles for selection of cracking-resistant materials

ISO 15544:2000/Amd 1:2009 石油和天然气工业.近海生产装置.应急反应用要求和指南.修改件1

Petroleum and natural gas industries - Offshore production installations - Requirements and guidelines for emergency response; Amendment 1

ISO 17078-3:2009 石油和天然气工业.钻井和生产设备.第3部分:偏心轴用运转工具、牵引工具和倾翻工具及插销

Petroleum and natural gas industries - Drilling and production equipment - Part 3: Running tools, pulling tools and kick-over tools and latches for side-pocket mandrels

ISO 13628-2:2006/cor 1:2009 石油和天然气工业.海底生产系统的设计和操作.第2部分:用于海底和海上的非粘合挠性管系统.技术勘误1

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 2: Unbonded flexible pipe systems for subsea and marine applications; Technical Corrigendum 1

ISO 23936-1:2009 石油、石化和天然气工业.与石油和天然气生产相关介质接触的非金属材料.第1部分:热塑性塑料

Petroleum, petrochemical and natural gas industries - Non-metallic materials in contact with media related to oil and gas production - Part 1: Thermoplastics

BS EN ISO 14691:2008 石油、石化和天然气工业.机械动力传输用柔性联轴节.一般用途

Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - General purpose applications

ANSI/NACE MR0175-2009 石油和天然气工业.油气产品内含硫化氢(H2S)环境中使用的材料,第1,2和3部分

Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production, Parts 1, 2, and 3

ASTM F2204-09 滨线响应技术描述用标准指南

Once the extent and type of shoreline oiling has been defined and documented using proper procedures (see Guides F1686 and F1687), decisions are made on the appropriate course of action for cleaning and restoration. In some cases, natural recovery may be the preferred approach whereas in other cases, active intervention may be appropriate. This guide summarizes the principal response techniques available. This guide is intended to minimize possible added impact to the environment that could result from overly-aggressive cleanup. In some cases, local priorities may dictate that intensive clean-up methods may be warranted. In all cases, concurrence to use such techniques should be obtained from all the major stakeholders and must comply with applicable regulations.1.1 This guide describes methods of cleaning and remediating shorelines containing stranded oil. The primary goal of any shoreline countermeasure is to aid recovery while minimizing additional impact. 1.2 This guide describes 22 different tactics that are available for consideration. These options range from natural recovery to active intervention. 1.3 The tactics listed may not be appropriate under all possible circumstances, and multiple countermeasures may be appropriate on the same shoreline. 1.4 This guide describes technical considerations for selecting one technique or another, or both. 1.5 Selection of specific countermeasures for use during a spill response are guided by the properties of the stranded oil, the degree of oiling, shoreline accessibility, shoreline geomorphology, mobility of available equipment, oceanographic and meteorological conditions, and the presence of sensitive natural and archeological resources. It is advisable to consult with the appropriate regulatory authorities as certain response options may require government authorization and approval. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Describing Shoreline Response Techniques

KS B ISO 10442:2008 石油、化学和气体设备工业.包装的整体式齿轮分离空气压缩机

이 표준은 석유 화학 및 가스 산업에 사용하기 위한 정속, 일체형 기어 장치가 연결된 원심

Petroleum, chemical and gas service industries-Packaged, integrally geared centrifugal air compressors

ISO 14691:2008 石油、石化和天然气工业.机械动力传输用软管.通用设备

Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - General-purpose applications

SY/T 6740-2008 井径仪校准方法

本标准规定了模拟信号、数字信号或频率信号输出的井径仪的技术要求、校准条件、校准项目和校准方法。 本标准适用于新制造、使用中及维修后井径仪的校准。

The calibration method of caliper

SY/T 0524-2008 导热油加热炉系统规范

本标准规定了导热油加热炉系统设计、制造、检验、试验与验收的基本要求。 本标准适用于固定式燃油、燃气导热油液相加热炉系统。 本标准适用于油气田和长输管道间接加热原油、天然气或其他介质的导热油加热炉系统。

Code for heater system with heat-transfer oil