L66 受计算机控制的电子器具 标准查询与下载

KS B 6935-2006 服务机器人的安全通则

이 규격은 3.에 정의되어 있는 서비스 로봇에 대한 설계, 제작에 대하여 안전상 고려해야

General rules on the safety of service robots

NF M62-204-4*NF ISO 17874-4:2006 放射性物质用遥控装卸设备.第4部分:动力机械手

Remote handling devices for radioactive materials - Part 4 : power manipulators.

ISO 10218-1:2006 工业环境的机器人.安全要求.第1部分:机器人

This part of ISO 10218 specifies requirements and guidelines for the inherent safe design, protective measures and information for use of industrial robots, as defined in Clause 3. It describes basic hazards associated with robots and provides requirements to eliminate, or adequately reduce, the risks associated with these hazards. Noise as a potential hazard is not dealt with in this part of ISO 10218, but will be fully covered in Part 2. This part of ISO 10218 does not apply to non-industrial robots although the safety principles established in ISO 10218 may be utilized for these other robots. Examples of non-industrial robot applications include, but are not limited to: undersea, military and space robots, tele-operated manipulators, prosthetics and other aids for the physically impaired, micro-robots (displacement < 1 mm), surgery or healthcare, and service or consumer products. NOTE 1 Requirements for robot systems, integration, and installation are covered in Part 2. NOTE 2 Additional hazards may be created by specific applications (e.g. welding, laser cutting, machining). These hazards may need to be considered during robot design.

Robots for industrial environments - Safety requirements - Part 1: Robot

JIS B 8436:2005 操作型工业机器人.机械接口.第1部分:板

この規格は，円形フランジ形メカニカルインタフエース(以下，メカニカルインタフふエースという。)の主要寸法，呼び方及び表示方法について規定する。これは，手動で装着するエンドエフエクタの互換性及び取付けの再現性を保証することを目的としたものである。

Manipulating industrial robots -- Mechanical interfaces -- Part 1: Plates

JIS B 8441:2005 操作型工业机器人.机械接口.第2部分:轴

この規格は，円形状突起をもつシャフト形メカニかルインタフェース(以下，メカニかルインタフェースという。)の主要寸法，呼び方及び表示方法について規定する。これは，手動で装着するエンドエフエクタの互換性及び取付けの再現性を保証することを目的としたものである。

Manipulating industrial robots -- Mechanical interfaces -- Part 2: Shafts

ARMY A-A-59156 A-2005 手动携带分散剂和暴动控制剂

Atherequirements. The contract or order should specify the following

DISPERSER AND RIOT CONTROL AGENT, MANUALLY CARRIED

KS B 7083-2004 工业机器人安全规范

이 규격은 3.에 정의되어 있는 산업용 로봇 및 로봇 시스템에 대한 설계, 제작, 프로그래

Manipulating indstrial robots-Safety

ARMY MIL-R-51516 VALID NOTICE 2-2004 暴动控制介质分散剂压力标准仪

MIL-R-51516 remains inactive for new design, however, the document is valid for use.

REGULATOR, PRESSURE, RIOT CONTROL AGENT DISPERSER

ARMY MIL-R-51446 VALID NOTICE 3-2004 CR暴动控制介质

MIL-R-51446 remains inactive for new design, however, the document is valid for use.

RIOT CONTROL AGENT, CR

ARMY MIL-R-51447 VALID NOTICE 3-2004 CR溶液暴动控制介质

MIL-R-51447 remains inactive for new design, however, the document is valid for use.

RIOT CONTROL AGENT, CR SOLUTION

ARMY MIL-R-51341 VALID NOTICE 2-2004 CS2暴动控制介质

MIL-R-51341 remains inactive for new design, however, the document is valid for use.

RIOT CONTROL AGENT, CS2

ARMY MIL-S-51371 C VALID NOTICE 2-2004 M254便携式暴动控制介质分散剂维修箱

MIL-S-51371C remains inactive for new design, however, the document is valid for use.

SERVICE KIT, PORTABLE RIOT CONTROL AGENT DISPERSER, M254

ARMY MIL-R-50090 D VALID NOTICE 2-2004 CS1暴动控制介质

MIL-R-50090D remains inactive for new design, however, the document is valid for use.

RIOT CONTROL AGENT, CS1

ARMY MIL-R-51029 C VALID NOTICE 2-2004 CS暴动控制介质

MIL-R-51029C remains inactive for new design, however, the document is valid for use.

DETAIL SPECIFICATION RIOT CONTROL AGENT, CS

BS EN ISO 9409-1:2004 操作型工业机器人.机械接口.板型

The methods covered are as follows:

Manipulating industrial robots - Mechanical interfaces - Plates

ISO 9409-1:2004 操作工业机器人.机械接口.第1部分:板

This part of ISO 9409 defines the main dimensions, designation and marking for a circular plate as mechanical interface. It is intended to ensure the exchangeability and to keep the orientation of hand-mounted end effectors. This part of ISO 9409 does not define other requirements of the end effector coupling device. This part of ISO 9409 does not contain any correlation of load-carrying ranges, as it is expected that the appropriate interface is selected depending on the application and the load-carrying capacity of the robot. The mechanical interfaces specified in this part of ISO 9409 will also find application in simple handling systems which are not covered by the definition of manipulating industrial robots, such as pick-and-place or master-slave units.

Manipulating industrial robots - Mechanical interfaces - Part 1: Plates

JEDEC JESD22-B104C-2004 机械冲击

The Mechanical Shock Test Method is intended to evaluate component(s) for use in electrical equipment. It is intended to determine the compatibility of the component(s) to withstand moderately severe shocks as a result of suddenly applied forces or abrupt change in motion produced by handling, transportation or field operation. Mechanical Shock of this type may disturb operating characteristics, particularly if the shock pulses are repetitive. This is a destructive test intended component qualification. It is normally applicable to cavity-type packages.

Mechanical Shock

KS B 7107-2003 电气空压式定位器的性能评估方法

이 규격은 전기 공압식 positioner의 성능 평가를 위한 시험 방법을 기술한 것이

Method of evaluating the performance of positioner with analog input signal and pneumatic output

KS B 7094-2003 技术制图机.技术规格项目

이 규격은 플로터의 시방서에 기재하는 항목에 대하여 규정한다.

Plotters-Specified items

ISO 9409-2:2002 操纵工业机器人.机械接口.第2部分:轴

This part of ISO 9409 defines the main dimensions, designation and marking for a shaft with cylindrical projection as mechanical interface. It is intended to ensure the exchangeability and to keep the orientation of hand-mounted end effectors. This part of ISO 9409 does not contain any correlation of load-carrying ranges. The mechanical interfaces specified in this part of ISO 9409 will also find application in simple handling systems which are not covered by the definition of manipulating industrial robots, such as pick-and-place or master-slave units.

Manipulating industrial robots - Mechanical interfaces - Part 2: Shafts