T22 承载系统 标准查询与下载
共找到 313 条与 承载系统 相关的标准，共 21 页
This International Standard specifies two laboratory methods for testing certain essential fatigue strength characteristics of wheels intended for road use on passenger cars as defined in ISO 3833. The test methods are a) dynamic cornering fatigue test; b) dynamic radial fatigue test.
Road vehicles - Passenger car wheels for road use - Test methods
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2015-06
- 实施
本标准定义了表征车轮几何均匀性的参数，描述了这些参数的测量原理。 本标准规定了汽车车轮径向跳动峰间值、轴向跳动峰间值、径向跳动平均值一次谐波以及轴向跳动平均值一次谐波的要求。 本标准适用于5°DC、5°SDC、5°FB和15°DC的汽车车轮。
Road vehicle.Wheels.Requirements and measuring methods of radial and lateral run-out
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2015-04-30
- 实施
- 2015-10-01
本标准规定了Ⅰ和Ⅱ两种实验室试验方法，用来评定车轮受到垂直于轴线方向的冲击时车轮的强度和安全性能。两种方法，可选其一进行试验。 本标准适用于乘用车轻合金车轮。
Passenger cars.Light alloy wheels.90° impact test procedure
- ICS
- 43.020
- CCS
- T22
- 发布
- 2015-04-30
- 实施
- 2015-10-01
Motor vehicles. Antiskid studs. Technical requirements and test methods
- ICS
- 43.040.50;83.160.10
- CCS
- T22
- 发布
- 2015
- 实施
- 2017-04-01
Motor vehicles. Silent-blocks. Technical requirements and test methods
- ICS
- 43.040.01
- CCS
- T22
- 发布
- 2015
- 实施
- 2017-04-01
本标准规定了以装饰及防腐为目的的汽车车轮表面油漆涂层的技术要求和试验方法。本标准适用于汽车车轮的表面油漆涂层。
Wheels for motor vehicles.Surface paint coatings
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2014-10-14
- 实施
- 2015-04-01
本标准规定了车轮静不平衡量要求及检测方法。本标准适用于汽车车轮。
Static unbalance requirements and test methods of vehicle wheels
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2014-10-14
- 实施
- 2015-04-01
本标准规定了汽车辐板式车轮在轮毂上安装尺寸的检验方法。本标准适用于汽车辐板式车轮。
Disc wheels.Measurement methods for dimensional characteristics of attachment on hub
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2014-10-14
- 实施
- 2015-04-01
This European Standard defines metrological and technical requirements and tests of tyre pressure measuring instruments. Tyre pressure measuring instruments (often referred to as Tyre Pressure Gauges, [TPG]) are for the inspection of pressure and/or inspection of inflation/deflation of tyres of motor vehicles. It establishes in the context of motor vehicles tyres, the minimum characteristics of the chain of measurement of tyre pressure measuring instruments intended to inspect or adjust the pressure of tyres inflated by air or nitrogen. These devices, classified in different categories, are hereinafter referred to by generic term, "tyre pressure measuring instruments". This chain of measurement consists of all the elements between the tyre valve and the display device (connector, hose, control device, measurement components, reservoir, preset device etc.). They indicate the pressure difference (pe) between the air or the nitrogen in the tyre and the atmosphere. The field of application established above can be extended to other applications where no specific standard exists. Because of the influence of tyre pressure on road safety and energy efficiency, periodical verification of tyre pressure measuring instruments is strongly recommended.
Tyre pressure measuring instruments - Devices for inspection of pressure and/or inflation / deflation of tyres for motor vehicles - Metrology, requirements and testing
- ICS
- 17.100;43.180;83.160.10
- CCS
- T22
- 发布
- 2014-08
- 实施
This International Standard specifies the interchangeability dimensions of ISO core chambers Nos. 1, 2, 3 and 4 for tyre valves. For the applicability of the core chambers, see ISO 9413 [1].
Tyre valves - ISO core chambers No. 1, No. 2, No. 3 and No. 4
- ICS
- 83.160.01
- CCS
- T22
- 发布
- 2014-04
- 实施
La présente partie de l'ISO 4000 spécifie la désignation, le profil et les cotes des jantes (à base creuse) coniques à 5o, principalement destinées aux voitures particulières.
Passenger car tyres and rims - Part 2 : rims
- ICS
- 43.040.50;43.100;83.160.10
- CCS
- T22
- 发布
- 2014-02-08
- 实施
- 2014-02-08
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for which bearing setting is manually adjusted. Assemblies using spacers to control bearing preload and endplay may differ in geometry and bearing componentry.
Disc Wheel Hub/Spoke Wheel and Axle Interface Dimensions - Truck and Bus
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2014-02-03
- 实施
- 2018-08-10
Passenger car tyres and rims. Rims
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2013-12-31
- 实施
- 2013-12-31
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3911, Wheels and rims for pneumatic tyres-Vocabulary, designation and marking
Passenger car tyres and rims.Part 2: Rims
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2013-12
- 实施
本标准规定了乘用车辐板式车轮在轮毂上安装所要求的相关尺寸。本标准规定的安装方式是以螺栓孔球面或锥面定位的安装方式,中心孔定位的平面安装方式不在本标准范围内。本标准适用于乘用车辐板式车轮。
Disc wheels for passenger car. Dimensional of attachment on hub
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2013-10-17
- 实施
- 2014-03-01
本标准规定了与M18×1.5、M20×1.5、M22×1.5螺柱配合带平垫圈的六角螺母的基本尺寸。本标准适用于以中心孔定位的平面安装的车轮固定螺母。
Commercial road vehicles.Flat attachment wheel fixing nuts
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2013-10-17
- 实施
- 2014-03-01
本标准规定了与M18×1.5、M20×1.5、M22×1.5螺柱配合带平垫圈的六角螺母的试验方法和性能要求。本标准适用于商用车用M18、M20、M22螺母。
Commercial vehicles.Flat attachment fixing nut.Test Methods
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2013-10-17
- 实施
- 2014-03-01
本标准规定了平衡块的结构、质量及公差、标志及汽车车轮在不装轮胎的情况下，平衡块的性能要求和试验方法。本标准适用于汽车用钢制车轮和轻合金车轮。
Vehicle wheels.balance weight
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2013-10-17
- 实施
- 2014-03-01
Aircraft tyres and rims - Part 1: specifications
- ICS
- 83.160.20
- CCS
- T22
- 发布
- 2013-10-04
- 实施
- 2013-10-04
This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice establishes uniform minimum labeling for disc wheels and demountable rims used in trucks, bus, and trailer applications.
Labeling Disc Wheel and Demountable Rims Trucks
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2013-05-23
- 实施
- 2013-09-13
