T43 载货汽车 标准查询与下载

UL 558-2012 内燃机驱动的工业卡车

UL Standard for Safety Industrial Trucks@ Internal Combustion Engine-Powered (Tenth Edition; Reprint with revisions through and including November 20@ 2017)

DIN ISO 27956:2011 公路车辆.厢式货车的货物固定要求和试验方法(ISO 27956-2009)

This International Standard applies to vehicle-relevant equipment for the seceuring of cargo in delivery vans with a gross vehicle mass up to 7.5t. This International Standard specifies minimum requirements and test methods for securing cargo ina reliable and roadworthy way, in order to protect occupants against injuries caused by shifting cargo.

Road vehicles - Securing of cargo in delivery vans - Requirements and test methods (ISO 27956:2009)

SAE J682-2011 后轮飞溅和扔石头保护

For guidance only in regard to highway commercial motor vehicles where protection to the rear against rear wheel splash and stone throw is deemed necessary, the following clearance specifications are recommended.

Rear Wheel Splash and Stone Throw Protection

BS ISO 14793:2011 道路车辆.重型商用车辆和汽车.横向瞬态响应试验方法

Road vehicles. Heavy commercial vehicles and buses. Lateral transient response test methods

ANSI/NFPA 505-2011 包括型号命名,使用范围,改建,维护和操作的动力工业货车消防安全性标准

1.1.1 This standard shall apply to fork trucks, tractors, platform lift trucks, motorized hand trucks, and other specialized industrial trucks powered by electric motors or internal combustion engines. 1.1.2 This standard shall not apply to compressed air-operated or nonflammable compressed gas-operated industrial trucks, farm vehicles, or automotive vehicles for highway use.

Fire Safety Standard for Powered Industrial Trucks Including Type Designations, Areas of Use, Conversions, Maintenance, and Operations

KS B ISO 22915-7:2010 工业卡车.稳定性检验.第7部分:双向和多向卡车

이 표준은 경사식/고정식 마스트 혹은 포크 암을 가진 양방향 또는 다방향 차량의 안정도 검

Industrial trucks-Verification of stability-Part 7:Bidirectional and multidirectional trucks

KS B ISO 22915-21:2010 工业卡车.稳定性检验.第21部分:操作员座位可升高1200 mm以上的电动捡料车

이 표준은 KS B ISO 5053에서 정의한 1 200 mm로 인양된 운전자의 위치에 대

Industrial trucks-Verification of stability-Part 21:Order-picking trucks with operator position elevating above 1 200 mm

ISO 11026:2010 重型商用车辆和公共汽车.转动稳定性试验方法.闭合曲线试验

Heavy commercial vehicles and buses - Test method for roll stability - Closing-curve test

ASTM E2462-10 高机动多用途轮式车(HMMWV)货物床区罩(CBC)的标准性能规范

1.1 Scope8212;This specification covers the performance requirements for the Type I Cargo Bed Cover (CBC). The Type I Cargo Bed Cover is a removable general purpose rigid enclosure for the cargo bed of the M1152A1, M1152A1 with B2 Armor Kit, M1037, M1042, M1097, and M1113 High-Mobility Multipurpose Wheeled Vehicle (HMMWV). The Type I CBC provides environmental protection and security for mission equipment and items of general transport. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.3 The following safety hazards caveat pertains only to the test required portion, Section 4, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV, Type I

KS B ISO 24134:2009 工业卡车.自动性能的追加要求事项

이 표준은 산업용 트럭의 자동기능을 위한 운전자 조작장치 및 운전자 제어장치에 대한 안전

Industrial trucks-Additional requirements for automated functions on trucks

ISO 22915-21:2009 工业用卡车.稳定性检验.第21部分:操作员座位可升高1200 mm以上的电动捡料车

Industrial trucks - Verification of stability - Part 21: Order-picking trucks with operator position elevating above 1200 mm

ISO 22915-7:2009 工业卡车.稳定性检验.第7部分:双向和多向卡车

Industrial trucks - Verification of stability - Part 7: Bidirectional and multidirectional trucks

SANS 10187-1:2009 车辆负载稳当性.第1部分:一般要求

Specifies the safety problems and basic precautions relating to the securing of load on vehicles. Deals with the strength, selection, and use of securing systems, and gives recommendations for the securement of a variety of the more common types of load.

Load securement on vehicles Part 1: General requirements

SAE J1301-2009 卡车变形分类

The scope and purpose of this SAE Recommended Practice is to provide a classification system for deformation sustained by trucks involved in collisions on the highway. Application of the document is limited to medium trucks, heavy trucks, and articulated combinations. The TDC classifies collision contact deformation, as opposed to induced deformation, so that the deformation is segregated into rather narrow limits or categories. Studies of collision deformation can then be performed on one or many data banks with assurance that data under study are of essentially the same type. Many of the features of the SAE J224 MAR80 have been retained in this document, although the characters within specific columns vary. each document must therefore be applied to the appropriate vehicle type. It is also important to note that the Truck Deformation classification (TDC) does not identify specific vehicle configurations and body types. The TDC is an expression, useful to persons engaged in vehicle safety, to appropriately describe a collision-damaged truck with consistences in oral and written communications. The TDC is also a research tool; however, it has not been designed for use in impact energy computation. The research community is cautioned not to attempt direct conversion calculations from the TDC to energy equivalents required to duplicate the damage. The system consists of seven alphanumeric characters arranged in a specific order to form a descriptive composite of the vehicle damage (see figure 1). The characters describe the principal force direction, location, specific area, type, and extent of damage. The individual character positions are referenced by column number for identification of each classification is provided in subsequent sections.

Truck Deformation Classification

BS ISO 20898:2008 工业卡车.电气要求

Industrial trucks - Electrical requirements

BS ISO 6292:2008 机动工业用卡车和牵引车.制动性能和部件强度

Powered industrial trucks and tractors - Brake performance and component strength

BS ISO 22915-1:2008 工业卡车.稳定性校验.一般要求

Industrial trucks - Verification of stability - General

ISO 27956:2009 道路车辆.货物交付车的保护.要求和试验方法

Road vehicles - Securing of cargo in delivery vans - Requirements and test methods

VC 8025-2010 N2和N3类机动车的强制性规范

This specification covers the requirements for motor vehicle models of category N2 and N3, not previously registered or licensed in South Africa, designed or adapted for operation on a public road. The requirements of this specification shall, in so far

Compulsory specification for motor vehicles of category N2 and N3

NF H96-332/IN1:2008 工业卡车的安全.卡车上自动功能的附加要求

Safety of industrial trucks - Additional requirements for automated functions on trucks.