T43 载货汽车 标准查询与下载
共找到 268 条与 载货汽车 相关的标准，共 18 页
This International Standard specifies two laboratory methods for testing certain essential strength characteristics of disc wheels intended for road use on commercial vehicles, buses, trailers, and multipurpose passenger vehicles, as defined in ISO 3833. The test methods are — dynamic cornering fatigue test and — dynamic radial fatigue test.
Road vehicles - Wheels/rims for commercial vehicles - Test methods
- ICS
- 43.040.50
- CCS
- T43
- 发布
- 2015-08
- 实施
Operational service vehicles for the transport of persons under detention. Technical requirements and test methods
- ICS
- 43.160
- CCS
- T43
- 发布
- 2015
- 实施
- 2017-04-01
Automobile vehicles for transportation of food liquids. Technical requirements and test methods
- ICS
- 43.080.10
- CCS
- T43
- 发布
- 2015
- 实施
- 2017-04-01
Industrial trucks — Additional requirements for automated functions on trucks
- ICS
- 53.060
- CCS
- T43
- 发布
- 2014-12-23
- 实施
- 2014/12/23
This part of ISO 22915 specifies tests for verifying the stability of pedestrian-propelled trucks. It is applicable to — straddle, pallet and platform stacker trucks with capacities not exceeding 1000kg, with manual or battery-powered lift; — scissors lift pallet trucks with lift heights up to 1000 mm and rated capacity up to 1000kg, with manual or battery-powered lift; — platform trucks. It also applies to trucks operating under the same conditions when equipped with load-handling attachments. It is not applicable to trucks with retractable devices such as a mast or fork.
Industrial trucks - Verification of stability - Part 16: Pedestrian-propelled trucks
- ICS
- 53.060
- CCS
- T43
- 发布
- 2014-07
- 实施
This part of ISO 22915 specifies the tests to verify the stability of single-side-loading trucks with tiltable or non-tiltable mast or fork arms. It is applicable to trucks fitted with fork arms and/or attachments.
Industrial trucks - Verification of stability - Part 5: Single-side-loading trucks
- ICS
- 53.060
- CCS
- T43
- 发布
- 2014-07
- 实施
Road vehicles. Heavy commercial vehicle combinations and articulated buses. Lateral stability test methods
- ICS
- 43.080.01
- CCS
- T43
- 发布
- 2014-02-28
- 实施
- 2014-02-28
Road vehicles. Heavy commercial vehicle combinations and articulated buses. Lateral stability test methods
- ICS
- 43.080.01
- CCS
- T43
- 发布
- 2014-02-28
- 实施
- 2014-02-28
Freight wagons. Requirements to structural strength and dynamic qualities
- ICS
- 03.220.30
- CCS
- T43
- 发布
- 2014
- 实施
- 2015-11-01
本标准规定了汽车顶部装载装置的术语和定义、类别代号、要求、试验方法、检验规则、标志、说明书、包装、运输和储存。本标准适用于在M1类和G类道路车辆外顶部安装的装载装置,以下简称“车顶装载装置”。
Roof load carriers for road vehicles
- ICS
- 43.040.60
- CCS
- T43
- 发布
- 2013-10-17
- 实施
- 2014-03-01
Industrial trucks - Verification of stability - Part 1: general
- ICS
- 53.060
- CCS
- T43
- 发布
- 2013-08-24
- 实施
- 2013-08-24
Safety of industrial trucks - Operation in potentially explosive atmospheres - Use in flammable gas, vapour, mist and dust; German version EN 1755:2000+A2:2013
- ICS
- 53.060
- CCS
- T43
- 发布
- 2013-08
- 实施
Safety of industrial trucks - Operation in potentially explosive atmospheres - Use in flammable gas, vapour, mist and dust
- ICS
- 53.060
- CCS
- T43
- 发布
- 2013-06-15
- 实施
本标准规定了低速汽车使用说明书的基本要求和编制方法。本标准适用于低速汽车整车使用说明书的编制。
Low-speed vehicles.Rules to drafting operator's manuals
- ICS
- 65.060
- CCS
- T43
- 发布
- 2013-04-25
- 实施
- 2013-09-01
本标准规定了低速货车驱动桥连接尺寸。本标准适用于低速货车后桥。
Low-speed goods vehicles.Drive axle mounting dimensions
- ICS
- 65.060
- CCS
- T43
- 发布
- 2013-04-25
- 实施
- 2013-09-01
This SAE Standard establishes the minimum construction and performance requirements for seven conductor 1/8 - 2/10 - 4/12 cable for use on trucks, trailers and converter dollies. Where appropriate, the standard refers to two types of cables, (Type F and S, described later in the standard), due to the variation in the performance demands of cables used in flexing and stationary applications. While the document's title refers to ABS Power to differentiate the document from the SAE J 1067 standard that it supersedes, the scope applies to both the primary green cable for powering ABS and lighting and the yellow auxiliary cable of the same construction.
Seven Conductor Cable for ABS Power Truck and Bus
- ICS
- 43.040.10
- CCS
- T43
- 发布
- 2013-02-01
- 实施
- 2017-12-22
This part of ISO 3691 gives safety requirements and the means for their verification for the following types of self-propelled industrial trucks (hereafter referred to as trucks), as defined in ISO 5053: a)industrial counterbalanced trucks; b)reach trucks with retractable mast or retractable fork arm carriage; c)straddle trucks; d)pallet-stacking trucks; e)high-lift platform trucks; f)trucks with elevating operator position up to 1 200 mm; g)side-loading trucks (one side only); h)lateral-stacking trucks (both sides), and lateral- and front-stacking trucks; i)pallet trucks; j) bidirectional and multidirectional trucks; k) tractors with a drawbar pull up to and including 20 000 N; l) rough-terrain counterbalanced trucks; m) industrial trucks powered by battery, diesel, gasoline or LPG (liquefied petroleum gas).
Industrial trucks - Safety requirements and verification - Part 1: Self-propelled industrial trucks, other than driverless trucks, variable-reach trucks and burden-carrier trucks (ISO 3691-1:2011); German version EN ISO 3691-1:2012
- ICS
- 53.060
- CCS
- T43
- 发布
- 2012-12
- 实施
This SAE Recommended Practice establishes uniform minimum labeling for disc wheels and demountable rims used in trucks, bus, and trailer applications.
Labeling Disc Wheel and Demountable Rims Trucks
- ICS
- 43.040.50
- CCS
- T43
- 发布
- 2012-09-27
- 实施
- 2012-09-29
This document supersedes SAE J819- Engine Cooling System Field Test. The purpose of this SAE Recommended Practice is to establish a testing procedure to determine the performance capability of the engine cooling systems, including charge air coolers on heavy-duty vehicles with liquid-cooled internal combustion engines. The definition of heavy vehicles for this document includes, but is not limited to, on and off highway trucks, cranes, drill rigs, construction, forestry and agricultural machines. Vehicles equipped with side or rear-mounted radiators may require an alternate procedure of a towing dynamometer because of peculiar aerodynamics. Testing is generally conducted to determine compliance with cooling criteria established by the engine manufacturer or the end product user to meet a desired engine reliability goal.
Heavy Duty Vehicle Cooling Test Code
- ICS
- 43.060.30
- CCS
- T43
- 发布
- 2012-09-19
- 实施
- 2017-12-14
本标准规定了重型汽车环境标志产品的基本要求、技术内容及其检验方法。 本标准适用于重型汽车。
Technical requirement for environmental labeling products.Heavy-duty vehicles
- ICS
- 01.040.13
- CCS
- T43
- 发布
- 2012-07-03
- 实施
- 2012-10-01
