P94 金属设备与工艺管道安装工程 标准查询与下载
共找到 770 条与 金属设备与工艺管道安装工程 相关的标准，共 52 页
General Requirements for Air Separation Plant Piping Installation
- ICS
- 23.040.01
- CCS
- P94
- 发布
- 2020-12-01
- 实施
- 2020-12-15
Gas ultrasonic flowmeter installation and construction requirements
- ICS
- 17.120.10
- CCS
- P94
- 发布
- 2020-12-01
- 实施
- 2020-12-15
Installation and use requirements for combustible gas detection and alarm
- ICS
- 17.120.10
- CCS
- P94
- 发布
- 2020-12-01
- 实施
- 2020-12-15
Gas turbine flowmeter installation and construction requirements
- ICS
- 17.120.10
- CCS
- P94
- 发布
- 2020-12-01
- 实施
- 2020-12-15
Installation and construction requirements of gas Roots flowmeter
- ICS
- 17.120.10
- CCS
- P94
- 发布
- 2020-12-01
- 实施
- 2020-12-15
General requirements for air separation plant valve installation
- ICS
- 23.060.01
- CCS
- P94
- 发布
- 2020-12-01
- 实施
- 2020-12-15
Construction specifications for geological disaster prevention and control projects for oil and gas transmission pipelines
- ICS
- 75.2
- CCS
- P94
- 发布
- 2020-10-23
- 实施
- 2021-02-01
Technical standards for welding and non-destructive testing of corrosion-resistant alloy bimetallic composite pipes
- ICS
- 75.2
- CCS
- P94
- 发布
- 2020-10-23
- 实施
- 2021-02-01
Rules for this Code Section have been developed considering the needs for applications that include piping typically found in electric power generating stations, industrial and institutional plants, geothermal heating systems, and central and district heating and cooling systems. 本规范部分的规则已考虑到应用的需求，包括发电站、工业和机构工厂、地热供暖系统以及中央和区域供暖和制冷系统中常见的管道。
Power Piping
- ICS
- 23.040.01
- CCS
- P94
- 发布
- 2020-09-30
- 实施
- 2020-09-30
This Code is applicable to piping in gaseous and liquid hydrogen service and to pipelines in gaseous hydrogen service. This Code is applicable up to and including the joint connecting the piping to associated pressure vessels and equipment but not to the vessels and equipment themselves. It is applicable to the location and type of support elements but not to the structure to which the support elements are attached. The design for pressure and temperature shall be in accordance with the requirements of Part IP for industrial piping and Part PL for pipelines. This Code is presented in the following parts and appendices: (a) Part GR — General Requirements. Part GR contains requirements applicable to and referenced by other parts. It contains definitions and requirements for materials, welding, brazing, heat treating, forming, testing, inspection, examination, operation, and maintenance. It also contains quality system topics common to the other parts. (b) Part IP — Industrial Piping. Part IP includes requirements for components, design, fabrication, assembly, erection, inspection, examination, and testing of piping. (c) Part PL — Pipelines. Part PL sets forth requirements for components, design, installation, and testing of hydrogen pipelines. (d) Mandatory Appendices I through IX (e) Nonmandatory Appendices A through F Each part defines requirements for piping or pipelines, as applicable, within its scope. The requirements are different for different aspects of components, design, fabrication, installation, assembly, erection, inspection, examination, and testing. It is required that each part be used in conjunction with the General Requirements section but independent of the other parts. The joint connecting piping governed by two different parts shall be subject exclusively to the requirements of one of the two parts. It is not intended that this edition of this Code be applied retroactively to existing hydrogen systems. 本规范适用于气态和液氢工况中的管道以及气态氢工况中的管道。本规范适用于并包括将管道连接到相关压力容器和设备的接头，但不适用于容器和设备本身。它适用于支撑元件的位置和类型，但不适用于支撑元件所附着的结构。压力和温度的设计应符合工业管道IP部分和管道PL部分的要求。本准则分为以下部分和附录： （a） 遗传资源部分——一般要求。GR部分包含适用于其他部分并被其他部分引用的要求。它包含材料、焊接、钎焊、热处理、成型、测试、检查、检查、操作和维护的定义和要求。它还包含其他部分共有的质量体系主题。 （b） 知识产权部分——工业管道。零件 IP 包括对管道的组件、设计、制造、装配、安装、检查、检查和测试的要求。 （c） PL部分——管道。PL部分规定了氢气管道的组件，设计，安装和测试的要求。 （d） 强制性附录一至九 （e） 非强制性附录A至F 每个零件定义其范围内的管道或管线要求（如果适用）。组件、设计、制造、安装、组装、安装、检查、检查和测试的不同方面的要求不同。要求每个部分与“一般要求”部分一起使用，但独立于其他部分。由两个不同部分控制的接头连接管道应完全服从两个部分之一的要求。本规范的本版本不打算追溯适用于现有的氢气系统。
Hydrogen Piping and Pipelines
- ICS
- 23.040.01
- CCS
- P94
- 发布
- 2019-12-20
- 实施
- 2019-12-20
Design and construction specifications for laying optical cables (silicon core tubes) in the same trench of oil and gas transmission pipelines
- ICS
- 23.040.20：75.010
- CCS
- P94
- 发布
- 2019-11-04
- 实施
- 2020-05-01
This document, in conjunction with ISO 11299-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of gas supply networks. It applies to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipe of either solid wall single layer or co-extruded layer construction, which is reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe liner, as well as associated fittings and joints for the construction of the lining system. This document is not applicable for coated PE pipes having a peelable, contiguous, thermoplastics additional layer on the outside of the pipes. It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature. NOTE For other operating temperatures, guidance is given in ISO 4437-5:2014.
Plastics piping systems for renovation of underground gas supply networks - Part 3: Lining with close-fit pipes
- ICS
- 23.040.20;23.040.45;75.200
- CCS
- P94
- 发布
- 2018-10-01
- 实施
This document specifies the requirements and test methods for plastics piping systems intended to be used for the renovation of underground gas supply networks. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is not applicable to the existing pipeline or any sprayed coatings or annular filler. This document gives the general requirements common to all relevant renovation techniques.
Plastics piping systems for renovation of underground gas supply networks - Part 1: General
- ICS
- 23.040.20;23.040.45;75.200
- CCS
- P94
- 发布
- 2018-10-01
- 实施
This document, read in conjunction with ISO 11299-1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground gas supply networks. It is applicable to polyethylene (PE) pipes of three different types: — PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes; — PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating; — Coated PE pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe (“coated pipe”), as described in Annex A. In addition it covers: — jointing of pipe lengths by means of butt fusion; — fabricated and injection-moulded fittings made of PE; It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature. NOTE For other operating temperatures, guidance is given in ISO 4437-5:2014.
Plastics piping systems for renovation of underground gas supply networks - Part 2: Lining with continuous pipes
- ICS
- 23.040.20;23.040.45;75.200
- CCS
- P94
- 发布
- 2018-10-01
- 实施
This Standard provides requirements for heat treatment of piping assemblies that meet the requirements of ASME B31 Code Sections. These requirements apply to (a) preheating (b) postweld heat treatment (PWHT) (c) postforming heat treatment (PFHT) required by the ASME B31 Code Sections for other fabrication processes, including forming processes such as bending (d) heat treatments required by contract specifications 本标准规定了符合ASME B31规范部分要求的管道组件热处理要求。这些要求适用于 （a） 预热 （b） 焊后热处理 （c） ASME B31 规范部分要求的其他制造工艺（包括弯曲等成形工艺）的成型后热处理 （PFHT） （d） 合同规格要求的热处理
Standard Heat Treatments for Fabrication Processes
- ICS
- 75.200
- CCS
- P94
- 发布
- 2018-05-15
- 实施
- 2018-05-15
This standard is intended to be used for rubber and plastic hose assemblies of the types: 1ST, 1SN, 2ST and 2SN according to DIN EN 853, 1TE, 2TE and 3TE according to DIN EN 854, 4SP, 4SH, R13 according to DIN EN 856, R15 according to ISO 3862 and 1SC and 2SC according to DIN EN 857 as well as plastic hoses assemblies of the types R7, R8 and R18 according to ISO 3949, appropriate for temperatures of -40° C up to + 100° C (hose types R13 and R 15 to 120°C) and hose connectors of the light and heavy duty series according to DIN ISO 12151-2 and DIN ISO 12151-3. This standard contains information about the most important criteria for selection and reference of hoses and connectors, the installation and connection dimensions as well as the requirements for the installation of hose assemblies. The comparative presentation of respective hoses types in Table 1 and Table 2 gives designers guidelines for the selection of hoses (nominal diameter and design) and their appropriate connectors, in case the piping of a system has already been determined. Further, guidelines are given in this standard for storage, life cycle and necessary inspections to ensure the full functionality of those assemblies.
Hydraulic fluid power - Hose assemblies - Dimensions, requirements
- ICS
- 23.100.40
- CCS
- P94
- 发布
- 2018-03-01
- 实施
Supervision and inspection rules for on-site manufacturing of spherical storage tanks
- ICS
- 23.020.10
- CCS
- P94
- 发布
- 2017-12-13
- 实施
- 2018-01-13
This Part of this European Standard specifies the requirements for inspection and testing of industrial piping as defined in EN 13480-1 to be performed on individual spools or piping systems, including supports, designed in accordance with EN 13480-3 and EN 13480-6 (if applicable), and fabricated and installed in accordance with EN 13480-4.
Metallic industrial piping - Part 5: Inspection and testing; German version EN 13480-5:2017
- ICS
- 23.040.01
- CCS
- P94
- 发布
- 2017-12-01
- 实施
The purpose of EN 13480 is to define the requirements for design, manufacture, installation, testing and inspection of industrial piping systems and supports, made of metallic materials with a view to ensure safe operation. EN 13480 is applicable to metallic piping above ground, ducted or buried, independent of pressure.
Metallic industrial piping - Part 1: General; German version EN 13480-1:2017
- ICS
- 23.040.01
- CCS
- P94
- 发布
- 2017-12-01
- 实施
This part of EN 13480 covers the requirements for materials (including clad materials) for industrial piping and supports covered by EN 13480-1 constructed of metallic materials and is currently limited to steels with sufficient ductility below the creep range. It specifies the assessment of compliance for these materials. It also provides rules for the establishment of technical delivery conditions for materials for industrial piping.
Metallic industrial piping - Part 2: Materials; German version EN 13480-2:2017
- ICS
- 23.040.01
- CCS
- P94
- 发布
- 2017-12-01
- 实施
