T21 传动系统 标准查询与下载

SAE J2312-2013 自动传输进气口过滤器试验规程

This test procedure is intended to apply to hydraulic pump suction filters and strainers used in automotive automatic transmissions that include hydraulic power pumps. The various paragraphs of Section 5, ""Test Procedures"", include a variety of tests and alternative tests that are not applicable to all filters and applications, so the engineer must specify which tests are to be performed for a particular application. These test procedures are intended to evaluate filter functional performance characteristics only, durability is not evaluated under this standard. Filter design requirements must be specified by the engineer on the filter assembly drawing, a

Automatic Transmission Intake Filter Test Procedure

SAE J2198-2013 自动皮带张紧装置术语汇编

This glossary was written to provide a consistent and uniform definition of terms used in describing the selection of an automatic belt tensioner as it applies to an automotive accessory drive system.

Glossary Automatic Belt Tensioner

SAE J2432-2012 PK选定V形肋带的性能试验

The following information covers accessory drive belt testing methods and includes test configurations, pulley diameters, power loads, and guidance for interpreting test data. Belt construction definitions are also documented. This information has been prepared from existing literature, including standards and data supplied by Producers and Users of V-ribbed belts.

Performance Testing of PK Section V-Ribbed Belts

SAE J1463-2012 推拉式离合器传动系安装尺寸规格

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice documents the typical transmission interface dimensions that are used with 14-in and larger pull-type clutches. Provide dimensional guidelines for current and future designs and thus promote interchangeability between various clutch and transmission combinations. Due to the variety of clutches and transmissions mounted clutch housings, no standard clearance envelope can be established without im

Pull-Type Clutch Transmission Installation Dimensions

SAE J1479-2012 汽车后拉式离合器术语

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Standard describes the terms or names of the parts, characteristics, and parameters of automotive pull-type clutches used in trucks, and of vehicle apparatus or components related to the pull type clutch. This document defines commonly used truck and bus clutch technical terms which may be found in industry publications. The purpose is to promote commonization of these terms for a clearer understanding of the techni

Automotive Pull-Type Clutch Terminology

SAE J1540-2012 手动传动效率和寄生损耗测量

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. Because of the intense focus on fuel economy and fuel emission standards, it has become imperative to optimize vehicle drivetrains. In light of this, component efficiencies have become an important factor in the drivetrain decision-making process. It has therefore become necessary to develop a universal standard to judge transmission efficiency. This SAE Recommended Practice specifies a test procedure which maps torque trans

Manual Transmission Efficiency and Parasitic Loss Measurement

DB34/T 1737-2012 驱动桥总成清洁度限值及评定方法

本标准规定了驱动桥总成清洁度的术语和定义、抽样、检验项目及要求，限值和测量方法。 本标准适应于 8T～13T 中重型驱动桥总成清洁度限值及评定方法。

Limit value and evaluation method of cleanliness of drive axle assembly

DB34/T 1738-2012 车桥总成中性盐雾试验方法和评价指标

本标准规定了中性盐雾试验的试验设备、试验方法及评定要求。 本标准适应于桥总成涂漆零部件和带涂镀层的螺栓螺母。

Neutral salt spray test method and evaluation index for axle assembly

SAE J636-2012 V形皮带和皮带轮

This specification covers standard dimensions, tolerances, and methods of measurement of V-belts and pulleys for automotive V-belt drives.

V-Belts and Pulleys

SAE J1079-2012 不同心离合器旋转测试规程

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice applies to driving ring type overcenter clutches such as are used in industrial power takeoffs. This document is intended to provide a uniform test procedure for overcenter clutches to determine either the rotative speed at which they will burst or a specified speed they will withstand without burst.

Overcenter Clutch Spin Test Procedure

SAE J1073-2012 弹簧离合器旋转试验规程

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice applies to spring-loaded clutches such as are used with manual shift type transmissions. This document is intended to provide a uniform test procedure for spring- loaded clutches to determine rotative speeds at which they will either burst or withstand a specified limiting speed.

Spring-Loaded Clutch Spin Test Procedure

BS ISO 13044-1:2012 道路车辆.重型商用汽车组合用24 V全自动耦合系统(FACS).第1部分:通用要求和定义

Road vehicles. 24 V fully automatic coupling systems (FACS) for heavy commercial vehicle combinations. General requirements and definitions

SAE J637-2012 汽车V形带传动

Although antiquated in design compared to today's serpentine belt drives, V belts are still common in many emerging markets. The scope is to stabilize the V belt drives. The following information is intended as a guide to be used for evaluating belt construction, source approval, and quality audit. This recommendation has been prepared from existing literature, including standards, specifications, and data supplied by both producers and users. These recommendations cover drive layout details and V-belt testing methods, including test layout, pulley diameters, torque loads and guidance for interpreting test data. The application of these automotive V-belts is to power engine or vehicle accessories that are physically attached to the engine.

Automotive V-Belt Drives

SAE J923-2012 卡车和公共汽车驱动轴用命名和术语

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice outlines basic nomenclature in common use for truck and bus drive axle designs. Over a period of years there have been many different designs introduced; however, for this report, only the most common have been selected and only their general construction is illustrated to show the nomenclature of the various parts.

Nomenclature and Terminology for Truck and Bus Drive Axles (Stabilized Type)

SAE J641-2012 液压驱动术语

Since the torque converter and fluid coupling have become commonly used components of automatic transmissions in industry, the SAE appointed a committee to standardize terminology, test procedure, data recording, design symbols, and so forth, in this field. The following committee recommendations will facilitate a clear understanding for engineering discussions, comparisons, and the preparation of technical papers. The recommended usages represent the predominating practice or the acceptable practice. Where agreement is not complete, alternates have been included for clarification. EXAMPLE: two systems of blade angle designations are described. Consequently when a blade angle is specified, the system should be designated. This SAE Recommended Practice deals only with the physical parts and dimensions and does not attempt to standardize the design considerations, such as the actual fluid flow angle resulting from the physical blade shape.

Hydrodynamic Drives Terminology

NF R15-517*NF ISO 12046:2012 同步带传动带 - 汽车用带 - 物理性能的测定.

Synchronous belt drives - Automotive belts - Determination of physical properties.

SAE J373-2012 单-双板弹簧负载离合器用箱内尺寸规格

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice defines the minimum internal dimensions for clutch housings to provide adequate clearance for single- and two-plate spring-loaded clutches. Consult SAE J617 for housing flange dimensions. Consult SAE J618 and J619 for spring-loaded clutch flywheel dimensions F and G and other dimensional data.

Housing Internal Dimensions for Single- and Two-Plate spring-Loaded clutches

SAE J618-2012 单板弹簧支撑离合器用飞轮

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice applies to flywheels for dry spring-loaded clutches used on internal combustion engines. figure 1 and Tables 1, 2, and 3 report information currently used in the industry. Clutches requiring other dimensions are also manufactured. Dimensions given are primarily for single- plate clutches. Flywheels for two plate clutches have the same dimensions if an adaptor for the intermediate plate and second driven disc is supplied with the clutch. If instead the flywheel is to be extended to adapt the intermediate plate and second driven member, consult the clutch manufacturer for the required J dimensions and drive arrangements for the intermediate plate.

Flywheels for Single-Plate Spring-Loaded Clutches

SAE J619-2012 双板弹簧支撑离合器用飞轮

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for dry spring-loaded clutches. Clutches to fit flywheels with configurations per this recommended practice may not be commercially available. Availability should be ascertained prior to flywheel design.

Flywheels for Two-Plate Spring-Loaded Clutches

ISO 13044-1:2012 道路车辆.重型商用汽车组合用24 V全自动耦合系统(FACS).第1部分:一般要求和定义

This part of ISO 13044 defines coupling classes, different levels of automation and the general limitations in terms of topology and procedures with respect to electrical and pneumatic connections. This part of ISO 13044 provides a framework under which detailed connector designs applicable for fifth wheel or drawbar couplings may be standardized. The framework refers to vehicle combinations that include trailers with a technical maximum mass in excess of 3500 kg.

Road vehicles - 24 V fully automatic coupling systems (FACS) for heavy commercial vehicle combinations - Part 1: General requirements and definitions