T21 传动系统 标准查询与下载

GOST R 53409-2009 车辆.摩擦干式离合器.一般技术要求和试验

Vehicles. Friction dgy clutch. General technical requirements and test methods

SAE J2475-2008 卡车和公共汽车轮子末端组件和轮轴接口尺寸规格

This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, seal and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, U, W, R, N and P.1.1 PurposeThe purpose of this recommended practice is to establish dimensional guidelines to promote a functional standardization of spindle dimensions for wheel end assemblies. Proper hub component dimensions can then be established.

Wheel End Assembly and Axle Spindle Interface Dimensions Truck and Bus

SAE J2817-2008 扭矩偏置差分的定义和测量

This SAE Recommended Practice covers passive torque biasing axle and center differentials used in passenger car and light truck applications. Differentials are of the bevel gear, helical gear and planetary types although other configurationsare possible.1.1 PurposeTo provide a common means to define, measure and quantify the operating characteristics of torque biasing differentials.

Definition and Measurement of Torque Biasing Differentials

QC/T 806-2008 汽车空调压缩机用电磁离合器技术条件

本标准规定了汽车空调压缩机用电磁离合器（以下简称离合器）的术语、要求、试验方法、检验规则及标志、包装、运输和储存。 本标准适用于汽车空调压缩机用电磁离合器。

Technical specincation of electromagnetic clutch for compressor of A/C

GOST R 52926-2008 车辆.汽车的连接传动轴.通用技术要求和试验方法

Vehicles. Joint drive shafts of cars. General technical requirements and test methods

BS ISO 23309:2007 液压传动系统.系统总成.冲洗法测定清洁度

ISO 23309:2007 specifies the procedures for flushing from the hydraulic lines of larger hydraulic fluid power systems solid particulate contamination that can be introduced during the initial build of a new hydraulic system or after maintenance or modification of an existing system. ISO 23309:2007 supplements, but does not replace, the requirements of the component supplier and customer, especially when those requirements are stricter than those specified by this International Standard.

Hydraulic fluid power systems - Assembled systems - Methods of cleaning lines by flushing

NF R15-505-2:2007 带传动.汽车行业用V型带、V型多楔带或同步带.第2部分:断裂时抗张强度的测定

Belt drives - V-belts, V-ribbed belts or synchronous belts for the automotive industry - Part 2 : determination of tensile strength at break.

JASO C201-2007 液力变矩器用试验规范

Test code for hydrodynamic torque converters

QC/T 777-2007 汽车电磁风扇离合器技术条件

本标准规定了汽车用电磁风扇离合器（以下简称电磁离合器）的技术要求、试验方法、检验规则、标志、包装、运输和储存。 本标准适用于汽车用电磁风扇离合器，与其他用途内燃机配套的电磁风扇离合器可参照采用。

Specifications for automobile electromagnetic fan clutch

ISO 3842:2006 道路车辆.(半挂牵引车)牵引座.互换性

This International Standard lays down the dimensional characteristics necessary for mounting and interchangeability of the fifth wheel mounted on a mounting plate (standard fifth wheel, Clause 4) or directly on the frame (direct-mounted fifth wheel, Clause 5) of towing vehicles for semi-trailers. It applies to the fifth wheels intended to hitch on semi-trailers equipped with a: 50 coupling pin as defined in ISO 337; 90 coupling pin as defined in ISO 4086. Dimensions not specified are left to the discretion of the component manufacturer. Test conditions and strength requirements to be met by 50 and 90 fifth wheel coupling are specified in ISO 8717.

Road vehicles - Fifth wheels - Interchangeability

ISO 18207:2006 道路车辆.3.5吨拖车.控制疲劳试验后联轴球焊接牵引支架

This International Standard defines a simplified and reliable check procedure of the mechanical coupling devices between light trailers, and towing vehicles, covered by ISO 3853 and European regulation (94/20/CE), which specify a dynamic test of mechanical resistance at the conclusion of which these devices should present neither fractures, splits, cracks, nor visible external deteriorations caused by the test. This International Standard is applicable to all the components of the mechanical coupling devices whose failure can cause the fracture of the attachment, manufactured out of steel, forged steel or cast steel (i.e. generally in ferromagnetic materials). In the case of use of other materials, the manufacturer will check their compatibility with the methods of nondestructive testing.

Road vehicles - Trailers up to 3,5 t - Control of welded towing brackets for coupling ball after fatigue testing

SAE J286-2006 SAE 2 号离合器摩擦试验机指南

This SAE Recommended Practice is intended as a guide toward implementation of a standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. The SAE No. 2 Friction Test Machine is used to evaluate the friction characteristics of automatic transmission plate clutch with automotive transmission fluids. It can also be used to conduct durability tests on wet friction systems. This document is intended for common use by both suppliers and end users to deine minimum test machine requirements to allow objective comparisons for wet friction material system performance.

SAE No. 2 Clutch Friction Test Machine Guidelines

KS R ISO 7653:2005 道路车辆.商用车辆.动力输出装置(PTO)和辅助传动组件之间的联结器

이 규격은 유압식 펌프와 같은 상용 차량에 설치되는 동력 인출 장치(PTO)와 보조 구동

Road vehicles-Commercial vehicles-Couplings between powertake-offs(PTO) and ancillary driven units

KS R ISO 7706:2005 道路车辆.商用车辆.动力输出装置(PTO)的自由空间

규격은 보통 그리고 강력 타입의 트럭 변속기 동력 인출 장치(PTO)의 틈새 덮개 치수를

Road vehicles-Commercial vehicles-Clearance envelope for power take-offs(PTO)

KS R ISO 7707:2005 商用道路车辆.后置式动力输出装置(PTO)的连接

이 규격은 후미 부착 동력 인출 장치(PTO)의 연결에 필수적인 치수를 규정한다. 이러한

Commercial road vehicles-Connections for rear-mountedpower take-offs(PTO)

SAE J2028-2005 前轮驱动常速连杆柔性封闭罩

This SAE Recommended Practice outlines qualification testing and performance related criteria of elastomeric boot seals used in constant velocity joint applications. These applications are referred to as front-wheel-drive halfshafts or axles, but can also be utilized in rear-wheel-drive halfshaft applications. For additional information regarding CV joint systems and their applications refer to SAE AE-7 "Universal Joint and Driveshaft Design Manual." The grease type and grease quantities, clamps and clamping mechanisms of an assemby are critical and considered to be the same as OEM, service, or aftermarket designation. Although joint lubricating grease and clamping mechanism are not addressed in this document, they are critical to a total system performance. The purpose of this document is to establish a uniform practice for those in the surface vehicle industry that specify and/or manufacture CV joint boot seals (boots) for OEM or aftermarket use with respect to qualification testing for physical and mechanical properties. This document is not intended to include or address propeller shaft, Power Take Off, heavy equipment, and marine boot seal applications.

Front-Wheel-Drive Constant Velocity Joint Boot Seals

SANS 10279:2005 汽车变速箱的再造

Covers the rebuilding of automatic and manual automotive gearboxes.Applies to gearboxes from which all the universal joints,in the case of manual gearboxes,the clutch plate and all clutch components and flexible attachment have been removed.Also applies

The rebuilding of automotive gearboxes

SAE J651-2005 乘用车和轻型卡车自动变速和自动传动试验规则

To provide a means of obtaining the performance characteristics of automatic transmissions and automatic transaxles. It outlines dynamometer tests that map the steady-state characteristics over a range of operations of an automatic transmission/automatic transaxle and provides a method of presenting test data. This procedure must be followed, with similar test facilities so that results obtained from different laboratories are comparable. For this SAE Recommended Practice, the transmission is defined as the complete automatic transmission or transaxle assembly between the engine and the driveshaft(s) used to effect a ratio change in transmitting power. For 4WD/AWD, it does not include transfer case or power take off subsystems. This test procedure deals with the aspect of conducting complete transmission and transaxle assembly testing. However, by its very nature a transmission should be viewed as a compilation of three major component systems: pump, torque converter, and gearbox (all ratio change elements). From a design perspective, it is important that the losses associated with each of these components be determined by conducting separate tests of each component under controlled test conditions that simulate the in-transmission operating conditions. Torque converter testing is described in SAE J643, and pump testing is described in SAE J2311. If done with strict attention to detail it is possible to subtract off the pump and torque converter losses from the transmission assembly losses in order to obtain gearbox losses only, eliminating the need to conduct a separate gearbox test.

Passenger Car and Light Truck Automatic Transmission and Automatic Transaxle Test Code

SAE J1532-2005 变速器冷油剂软管

This SAE Standard covers hose intended for use with automatic transmission cooling system applications. Type A hoses are intended for original equipment or replacement applications while Type B hoses are intended for aftermarket auxiliary cooler applications only. The reference fluid for tests requiring the use of automatic transmission fluid (ATF) shall be Dexron III / Mercon 5 or equivalent ATF that is agreed to by hose manufacturer and customer.

Transmission Oil Cooler Hose

ISO 2790:2004 带传动.汽车工业用V带及带轮.尺寸

This International Standard specifies the requirements for belts and pulleys for V-belt drives used for driving auxiliaries of internal combustion engines for the automotive industry.

Belt drives - V-belts for the automotive industry and corresponding pulleys - Dimensions