T21 传动系统 标准查询与下载

SAE J1499-2012 SAE 带式摩擦试验机指南

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice is intended as a guide toward implementation of a standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. The SAE band friction test method is used to evaluate the frictional characteristics of automatic transmission band friction materials with automatic transmission fluids. It can also be used to conduct durability tests on wet friction materials.

SAE Band Friction Test Machine Guidelines

QC/T 896-2011 电动汽车用驱动电机系统接口

本标准规定了电动汽车用驱动电机系统的电气接口型式、信号定义，对驱动电机系统的机械接口做了通用性的规定。 本标准适用于电动汽车用驱动电机系统，不适用于车用辅助电机系统。

Interface of electrical machine system for electric vehicles

QC/T 893-2011 电动汽车用驱动电机系统故障分类及判断

本标准规定了电动汽车用驱动电机系统故障的确认原则、故障模式和故障分类。 本标准适用于各类电动汽车用驱动电机系统。

Failure classification and assessment of electrical machine system for electric vehicle

DIN 73451:2011 离合器衬片.尺寸和公差

Clutch facings - Dimensions and tolerances

SAE J2228-2011 商用拖车和半拖车的中心轴的磨损极限

This SAE Recommended Practice applies to upper coupler kingpins for commercial trailers and semitrailers conforming to the dimensional requirements of SAE J700 when new and originally installed. The dimensions of SAE J700 are the frame of reference for this document. The purpose of this document is to establish maximum parameters for kingpin wear and to suggest a gauge configuration for inspecting kingpin wear. Kingpins exceeding the conditions of this specification must be removed from service and replaced.

Kingpin Wear Limits Commercial Trailers and Semitrailers

SAE J848-2011 商业拖车和半拖车的重型第五轮主销

This SAE Recommended Practice applies to fifth wheel kingpins for heavy- duty commercial trailers and semitrailers, used for off-highway operation or in hauling heavy loads.

Fifth Wheel Kingpin, Heavy-Duty Commercial Trailers and Semitrailers

SAE J2453-2011 手动变速箱和变速差速器效率以及附加损失测量

Because of the intense focus on CAFE and fuel emission standards, optimization of the automobile drivetrain is imperative. In light of this, component efficiencies have become an important factor in the drivetrain decision-making process. It has therefore become necessary to develop a universal standard to judge transmission efficiency. This SAE Recommended Practice specifies the dynamometer test procedure which maps a manual transmissions efficiency. The document is separated into two parts. The first compares input and output torque throughout a specified input speed range in order to determine "in-gear" transmission efficiency. The second procedure measures parasitic losses experienced while in neutral at nominal idling speeds and also churning losses while in gear. The application of this document is intended for passenger car and light truck. All references to transmissions throughout this document include transaxles.

Manual Transmission and Transaxle Efficiency and Parasitic Loss Measurement

SAE J2200-2011 客车和轻型卡车轴

This SAE Recommended Practice is intended to outline basic nomenclature for axle designs in common use for automotive drives. Over a period of years, there have been many different designs; however, for the purpose of this report, only the most common designs have been selected and only their general construction is illustrated to show the nomenclature of the various parts.

Passenger Car and Light Truck Axles

SAE J700-2011 联结器中心立轴在上部的商用挂车和半挂车

This SAE Standard applies to upper coupler kingpins for commercial trailers and semitrailers in the unladen condition. A 90 ± 1 degree angle extends (in all directions) from the centerline of the kingpin to the upper coupler plate surface within a 48.26 cm (19 in) radius. The upper coupler plate surface should not bow downward (convex) more than 0.635 cm (1/4 in) within a 48.26 cm (19 in) radius or more than 0.3175 cm (1/8 in) at a radius of 25.4 cm (10 in) from the kingpin. The upper coupler plate surface should not bow upward (concave) more than 0.15875 cm (1/16 in) within a 48.26 cm (19 in) radius.

Upper Coupler Kingpin Commercial Trailers and Semitrailers

SAE J133-2011 商用挂车和半挂车备用轮中心立轴的性能

The purpose of this SAE Recommended Practice is to establish test procedures and minimum performance standards for kingpins and their supporting structure manufactured to SAE specifications. The dimensions shown in SAE J 700 will permit the establishment of standard clearances in the installed condition which, in turn, will permit fifth wheel manufacturers to design their products to establish interchangeability with any kingpin made and installed to the SAE specification.

Fifth Wheel Kingpin Performance Commercial Trailers and Semitrailers

SAE J640-2011 液压驱动器的标志

The following system of symbols is recommended for use in technical papers and engineering reports dealing with hydrodynamic drives.

Symbols for Hydrodynamic Drives

QC/T 568.1-2011 汽车机械式变速器总成台架试验方法 第1部分：微型

QC/T 568的本部分规定了轻型车和微型车机械式变速器总成的台架试验方法。 本部分适用于输入扭矩不大于200N.m的乘用车和商用车机械式变速器总成。

Rig testing method for auto manual transmission assembly.Part 1:mini-vehicle

QC/T 29063.1-2011 汽车机械式变速器总成技术条件 第1部分：微型

QC/T 29063的本部分规定了轻型汽车和微型汽车机械式变速器总成的结构型式、技术要求、试验方法、检验规则、标志、包装、运输、储存及质量保证。 本部分适用于输入扭矩不大于200N.m的乘用车和商用车机械式变速器总成。

Technical specification for auto manual transmission assembly.Part 1:mini-vehicle

SAE J683-2011 轮胎防滑链间隙卡车,客车(市郊,城际和运输车除外),和车辆组合

The purpose of this SAE Information Report is to set up a guide as to body, frame, and wheel housing clearance to accommodate tire chains, and also the minimum bogie spacing to permit using chains on both axles. These dimensions apply to trucks, buses, and combinations of vehicles 10 001 lb (4535.06 kg) GVW and over, and are based upon recommendations of the Tire and Rim Association and of the National Association of chain Manufacturers. The diagram shows clearance for chains over the tire ONLY and allowance must be made for spring deflections in determining fender clearance.

Tire Chain Clearance Trucks, Buses (Except Suburban, intercity, and Transit Buses), and Combinations of Vehicles

SAE J643-2011 液压传动试验规程

The range of test conditions on the dynamometer shall be sufficient to determine the primary operating characteristics corresponding to the full range of vehicle operations. The characteristics to be determined are: a. torque ratio versus speed ratio and output speed; b. input speed versus speed ratio and output speed; c. efficiency versus speed ratio and output speed; d. capacity factor versus speed ratio and output speed; and e. input torque versus input speed.

Hydrodynamic Drive Test Code

SAE J1952-2010 全轮驱动系统分类

In this SAE Recommended Practice, attention will be given to passenger cars and light trucks (through Class III). The definitions are inteded to outline basic nomenclature and to categroize all-wheel drive concepts. The goal is to give those working in the field a common base for discussion regarding the type of all-wheel drive systems independent of marketing terminology.

All-Wheel Drive Systems Classification

ISO 1726-3:2010 道路车辆.牵引车和半拖挂车之间机械轴节.第3部分:半拖挂车备用轮接触面积要求

Road vehicles - Mechanical couplings between tractors and semi-trailers - Part 3: Requirements for semi-trailer contact area to fifth wheel

SAE J649-2010 自动传输功能术语

The following is a list of the most common terminology used in describing automatic transmission functions.

Automatic Transmission Functions Terminology

SAE J1459-2009 V-棱纹皮带及滑轮

This SAE Standard covers the dimensioning technique, tolerances, and methods of measurement of V-ribbed belts and mating pulleys for use on automotive accessory drives.

V-Ribbed Belts and Pulleys

KS R ISO 7656:2009 商业用道路车辆.尺寸代码

이 표준은 자동차 데이터 정보의 교환 및 전자 정보 처리를 위해 사용되는 상용 도로 차량에

Commercial road vehicles－Dimensional codes