T47 新能源汽车及其他类型汽车 标准查询与下载

QC/T 741-2014 车用超级电容器

本标准规定了电动道路车辆用超级电容器(电化学电容器)的要求、试验方法、检验规则、标志、包装、运输和储存。本标准适用于电动道路车辆用超级电容器(以下简称电容器)单体和模块。

Ultra-capacitor for electric vehicles

SAE J2578-2014 通用燃料电池车辆安全性用推荐实施规程

This SAE Recommended Practice identifies and defines requirements relating to the safe integration of the fuel cell system, the hydrogen fuel storage and handling systems (as defined and specified in SAE J2579) and high voltage electrical systems into the overall Fuel Cell Vehicle. The document may also be applied to hydrogen vehicles with internal combustion engines. This document relates to the overall design, construction, operation and maintenance of fuel cell vehicles. 1.1 Purpose The purpose of this document is to provide mechanical and electrical system safety guidelines, safety criteria and methodologies that should be considered when designing fuel

Recommended Practice for General Fuel Cell Vehicle Safety

SAE J2601-2014 轻型气态氢表面车辆用燃料添加协议

SAE J2601 establishes the protocol and process limits for hydrogen fueling of light duty vehicles. These process limits (including fuel temperature, the maximum fuel flow rate, and rate of pressure increase and end pressure) are affected by factors such as ambient temperature, fuel delivery temperature and initial pressure in the vehicle's compressed hydrogen storage system. SAE J2601-2014 establishes standard fueling protocols based on a look-up table approach with performance targets. The current standard is table-based and provides concise performance targets for both communications and non-communications fueling as described in Sections 7 through 10. An

Fueling Protocols for Light Duty Gaseous Hydrogen Surface Vehicles

QC/T 990-2014 电动汽车用锌空气电池

本标准规定了电动汽车用锌空气电池(以下简称电池)的术语和定义,符号及释义,要求,试验方法,检验规则,标志、包装、运输、储存。本标准适用于以机械更换式作为能量补充方式的电动汽车用锌空气电池。

Zinc-air batteries for electric road vehicle

GOST R ISO 12405-2-2014 电动道路车辆. 锂离子动力电池组和系统试验规范. 第2部分. 高能源应用

Electrically propelled road vehicles. Test specification for lithium-ion traction battery packs and systems. Part 2. High-energy applications

BS ISO 23828:2013 燃料电池道路车辆.能量消耗测量.供以压缩氢燃料的车辆

Fuel cell road vehicles. Energy consumption measurement. Vehicles fuelled with compressed hydrogen

BS CWA 16688:2013 电动汽车电池交换系统接口

Battery Swap Systems Interfaces for Electric Vehicles

DB44/T 1201-2013 电动汽车用车载充电装置的安全要求

本标准规定了输入功率不超过3.5kW，供电交流输入电压220V，符合II类电源安全要求的，为纯电动乘用车配备的车载充电装置的安全要求，包括装置安全工作的技术要求、测试方法、检验规则、标志、包装、运输和贮存等。 本标准适用于纯电动乘用车车载充电装置，其他类型的电动汽车充电装置也可参照使用。 本标准不适用混合动力电动汽车车载充电装置及工作在有易燃、爆炸性气体工作场所的电动汽车车载充电装置。

Safety requirements for on-board charging devices for electric vehicles

KS R IEC 61851-22:2013 电动车辆感应充电系统.第22部分:交流充电设备

KS C IEC 61851-1과 함께 이 표준은 IEC 60038에 따른 1 000 V 이하의 전기자동차 전도성 교류 충전설비에 관한 요구사항이다.이 표준은 전기자동차 충전에 사용될 수 있는 일반 범용 소켓-아웃렛을 갖는 조립체에는 적용하지않는다.이 표준은 유지 보수와 관련된 모든 안전 사항은 다루지 않는다.이 표준은 또한 모드 2에 사용되는 케이블 일체형 제어 박스(ICCB)에도 적용한다.이 표준에서 다루는 충전설비는 인화성 가스나 증기 및/또는 가연성 재료, 연료 또는 기타 인화성 또는 폭발성 재료가 있는 위험 지역에 배치하면 안 된다. 이러한 지역에 적용을 위하여 추가 요구사항을 적용할 수 있다.이 표준은 KS C IEC 61851-21의 온보드 장치에는 적용하지 않는다.이 표준은 전원 공급 장치와 ICCB 내부에 사용하는 전기 장치와 부품에는 적용하지 않으며, 내부에사용하는 전기 장치와 부품은 다른 표준에서 규정한다.

Electric vehicle conductive charging system－Part 22：AC electric vehicle charging station

ISO 23273:2013 燃料电池道路车辆.安全性规范.带压缩氢燃料汽车用氢危险防护措施

This International Standard specifies the essential requirements for fuel cell vehicles (FCV) with respect to the protection of persons and the environment inside and outside the vehicle against hydrogen-related hazards. It applies only to such FCV where compressed hydrogen is used as fuel for the fuel cell system. This International Standard does not apply to manufacturing, maintenance, and repair. The requirements of this International Standard address both normal operating (fault-free) and singlefault conditions of the vehicles.

Fuel cell road vehicles - Safety specifications - Protection against hydrogen hazards for vehicles fuelled with compressed hydrogen

QC/T 926-2013 轻型混合动力电动汽车（ISG型）用动力单元可靠性试验方法

本标准规定了轻型混合动力电动汽车(ISG型)用动力单元可靠性的试验方法。本标准适用于M类、N类和最大设计总质量不超过3.5t的M类混合动力电动汽车(ISG型)用动力单元。本标准不适用于怠速起停功能的考核。

The reliability test methods for powertrain unit of light-duty hybrid electric vehicles (ISG type)

QC/T 917-2013 燃气汽车专用手动截止阀

本标准规定了燃气汽车专用手动截止阀(以下简称截止阀)的定义、结构要求、技术要求、试验方法、检验规则、标志、包装、运输及储存。本标准适用于额定工作压力不大于20MPa(本标准所述压力均指表压)、环境温度为-40℃ ~ + 85℃、工作介质符合GB 18047要求的汽车用压缩天然气截止阀(以下简称CNG截止阀)及额定工作压力不大于2.2MPa、环境温度为-40℃ ~ + 85℃、工作介质符合GB 19159要求的汽车用液化石油气截止阀(以下简称LPG截止阀)。

Manual valve for gas vehicle

QC/T 916-2013 重型车用二甲醚单燃料发动机 技术条件

本标准规定了重型车用二甲醚单燃料发动机的技术要求、试验方法、检验规则、标志、包装、运输和储存的条件。本标准适用于设计车速大于25km/h的M、M、N和N类及最大设计总质量大于3500kg的M类机动车装用的二甲醚单燃料发动机(以下简称发动机)。

Specifications for mono-fuel DME engines of heavy-duty vehicles

QC/T 925-2013 超级电容电动城市客车 定型试验规程

本标准规定了超级电容电动城市客车新产品定型试验的实施条件、试验项目、试验方法、评定依据、试验程序以及试验报告等内容。本标准适用于采用超级电容器作为动力电源或主要以超级电容器作为动力电源的电动城市客车。

Ultracapacitor electric city bus.Engineering approval evaluation program

QC/T 914-2013 二甲醚汽车定型试验规程

本标准规定了燃用车用二甲醚燃料的汽车定型试验的试验条件及中止试验条件、试验项目和方法。本标准适用于M类和N类单燃料的二甲醚汽车。对于新开发的基本型二甲醚汽车,应按照相应的汽车定型试验规程和本标准适用的要求进行定型试验;对于在已经定型的汽车产品上安装二甲醚发动机和安装二甲醚专用装置的二甲醚汽车,应按本标准的相关要求进行定型试验;对于在已经定型的汽车产品上安装柴油-二甲醚双燃料发动机和安装相关专用装置的柴油-二甲醚双燃料汽车,应参照本标准的相关要求进行定型试验。

Engineering approval evaluation program of dimethyl ether vehicle

QC/T 915-2013 车用二甲醚钢瓶集成阀

本标准规定了车用二甲醚钢瓶集成阀的术语和定义、产品分类和型号标记方法、结构要求及主要参数、技术要求、试验方法、检验规则、标志、包装、运输及储存和出厂文件。本标准适用于公称工作压力为2.0MPa(本标准所述压力值均为表压),工作温度为-40℃~+ 60℃,以二甲醚为燃料的汽车用二甲醚钢瓶集成阀。

DME steel cylinder multivalve for vehicle

SAE J2579-2013 燃料电池和其他氢型车辆中燃料系统标准

The purpose of this document is to define design, construction, operational, and maintenance requirements for hydrogen fuel storage and handling systems in on-road vehicles. Performance-based requirements for verification of design prototype and production hydrogen storage and handling systems are also defined in this document. Complementary test protocols (for use in type approval or self-certification) to qualify designs (and/or production) as meeting the specified performance requirements are described. Crashworthiness of hydrogen storage and handling systems is beyond the scope of this document. SAE J2578 includes requirements relating to crashworthines

Standard for Fuel Systems in Fuel Cell and Other Hydrogen Vehicles

UL 2594-2013 电动汽车供应设备的安全性标准

Standard for Safety for Electric Vehicle Supply Equipment

SAE J2836/3-2013 分布式能源插电式电动汽车通信使用案例

This SAE Information Report establishes use cases for a Plug-in Electric Vehicle (PEV) communicating with an Energy Management System (EMS) as a Distributed Energy Resource (DER). The primary purpose of SAE J2836/3 is to define use cases which must be supported by SAE J2847/3. This document also provides guidance for updates to SAE J2847/2 to allow an inverter in an EVSE to use the PEV battery when operating together as a distributed energy resource (DER).

Use Cases for Plug-in Vehicle Communication as a Distributed Energy Resource

ANSI/UL 2594-2013 电动汽车供应设备的安全性标准

Standard for Safety for Electric Vehicle Supply Equipment