GB/T 17467-2010
High-voltage/low-voltage prefabricated substation

2020-10
Standard No.
GB/T 17467-2010
Language
Chinese
Release Date
2010
Published By
General Administration of Quality Supervision, Inspection and Quarantine of the People‘s Republic of China
Replace By
GB/T 17467-2020
Lastest
GB/T 17467-2020
Replace
GB/T 17467-1998
Scope
This standard specifies the conditions for use of high-voltage/low-voltage or low-voltage/high-voltage outdoor prefabricated substations with a rated AC voltage of 3.6kV to 40.5kV on the high-voltage side, including one or more transformers, with a frequency of 50Hz and below, and installed in places accessible to the public. , rated characteristics, general structural requirements and test methods. The substation is cabled and can be operated from inside (entry type) or outside (non-entry type) of it. The relevant provisions of this standard apply to designs where not all components are present (for example: installations consisting only of power transformers and low-voltage switchgear and controlgear).

GB/T 17467-2010 Referenced Document

  • GB 1094.1 Power transformers.Part 1: General*， 2013-12-17 Update
  • GB 1094.11 Power transformers- Part 11: Dry-type transformers
  • GB 1094.2 Power transformers.Part 2:Temperature rise for liquid-immersed transformers*， 2013-12-17 Update
  • GB 1094.3 Power transformers Part 3: Insulation levels,dielectric tests and external clearances in air
  • GB 1094.5 Power transformers.Part 5:Ability to withstand short circuit
  • GB 14048.1 Low-voltage switchgear and controlgear.Part 1:General rules*， 2012-12-31 Update
  • GB 3906-2006 Alternating-current metal-enclosed switchgear and controlgear for rated voltages above 3.6kV and up to and including 40.5 kV
  • GB 4208-2008 Degrees of protection provided by enclosure(IP code)
  • GB 7251.1-2005 Low-voltage switchgear and controlgear assemblies-Part 1:Type-tested and partially type-tested assemblies
  • GB/T 1094.10 Power transformers— Part 10：Determination of sound levels*， 2022-10-14 Update
  • GB/T 1094.7 Power transformers.Part 7: Loading guide for oil-immersed power transformers
  • GB/T 11022-1999 Common specifications for high-voltage switchgear and controlgear standards
  • GB/T 13540 Seismic qualification for high-voltage switchgear and controlgear
  • GB/T 1408.1 Insulating materials.Test methods for electric strength.Part 1:Test at power frequencies*， 2016-12-13 Update
  • GB/T 230.1 Metallic materials.Rockwell hardness test.Part 1:Test method*， 2018-05-14 Update
  • GB/T 2423.1 Environmental testing for electric and electronic products.Part 2:Test methods.Tests A:Cold
  • GB/T 2423.10 Environmental testing—Part 2:Test methods—Test Fc:Vibration(sinusoidal)*， 2019-06-04 Update
  • GB/T 2423.101 Environmental testing for electric and electronic products.Part 2:Test methods.Test: Inclinations and swings
  • GB/T 2423.102 Environmental testing for electric and electronic products.Part 2:Test method.Test:combined temperature(cold and heat)/low air pressure/vibration(sinusoidal)
  • GB/T 2423.11 Environmental testing for electric and electronic products. Part 2: Test methods. Test Fd: Random vibration wide band--General requirements
  • GB/T 2423.12 Environmental testing for electric and electronic products. Part 2: Test methods. Test Fda: Random vibration wide band--Reproducibility high
  • GB/T 2423.13 Environmental testing for electric and electronic products. Part 2: Test methods. Test Fdb: Random vibration wide band--Reproducibility medium
  • GB/T 2423.14 Environmental testing for electric and electronic products. Part 2: Test methods. Test Fdc: Random vibration wide band--Reproducibility low
  • GB/T 2423.15 Environmental testing for electric and electronic products.Part 2:Tests methods.Test Ga and guidance:Acceleration,steady
  • GB/T 2423.16 Environmental testing—Part 2: Test methods—Test J and guidance: Mould growth*， 2022-07-11 Update
  • GB/T 2423.17 Environmental testing for electric and electronic products.Part 2:Test method.Test Ka:Salt mist
  • GB/T 2423.18 Environmental testing—Part 2: Test methods—Test Kb:Salt mist, cyclic（sodium chloride solution）*， 2021-05-21 Update
  • GB/T 2423.19 Environmental testing.Part 2:Test methods.Test Kc:Sulphur dioxide test for contacts and connections*， 2013-11-12 Update
  • GB/T 2423.2 Environmental testing for electric and electronic products.Part 2:Test methods.Tests B:Dry heat
  • GB/T 2423.20 Environmental testing.Part 2: Test methods.Test Kd: Hydrogen sulphide test for contacts and connections*， 2014-09-30 Update
  • GB/T 2423.21 Environmental testing for electric and electronic products.Part 2 Test methods Test M:Low air pressure
  • GB/T 2423.22 Environmental testing.Part 2:Test methods.Test N:Change of temperature*， 2012-12-31 Update
  • GB/T 2423.23 Environmental testing.Part 2:Test methods.Test Q:Sealing*， 2013-11-12 Update
  • GB/T 2423.24 Environmental testing—Part 2: Test methods—Test S: Simulated solar radiation at ground level and guidance for solar radiation testing and weathering*， 2022-07-11 Update
  • GB/T 2423.25 Environmental testing for electric and electronic products.Part2:Tsets Tset Z/AM:Combined cold/low air pressure tests
  • GB/T 2423.26 Environmental testing for electric and electronic products.Part 2 Test methods TestZ/BM:Combined dry heat/low air pressure tests
  • GB/T 2423.27 Environmental testing—Part 2: Test methods—Test method and guidance: Combined temperature or temperature and humidity with low air pressure tests*， 2020-06-02 Update
  • GB/T 2423.28 Environmental testing for electric and electronic products.Part2:Test methods-Test T:Soldering
  • GB/T 2423.29 Environmental testing for electric and electronic products-- Part 2:Test methods Test U:robustness of terminations and integral mounting devices
  • GB/T 2423.3 Environmental testing—Part 2：Testing method—Test Cab:Damp heat,steady state*， 2016-12-13 Update
  • GB/T 2423.30 Environmental testing.Part 2:Test methods.Test XA and guidance:Immersion in cleaning solvents*， 2013-12-17 Update
  • GB/T 2423.31 Basic environmental testing procedures for electric and electronic products--Test:inclinations and motions
  • GB/T 2423.32 Environmental testing for electric and electronic products.Part 2:Test methods.Test Ta:Solderability test by the wetting balance method
  • GB/T 2423.33 Environmental testing—Part 2: Test methods—Test Kca: High concentration sulfur dioxid*， 2021-05-21 Update
  • GB/T 2423.34 Environmental testing.Part 2:Test methods.Test Z/AD:Composite temperature/humidity cyclic test*， 2012-12-31 Update
  • GB/T 2423.35 Environmental testing—Part 2:Tests and guidance—Combined climatic(temperature/humidity)and dynamic(vibration/shock) tests*， 2019-06-04 Update
  • GB/T 2423.36 Environmental testing for electric and electronic products Part.2:Tests Tests Z/BFc:Combined dry heat/vibration(sinusoidal)tests for both heat-dissipating and non-heat-dissipating specimens
  • GB/T 2423.37 Environmental testing for electric and electronic products Part 2: Test methods Test L: Dust and sand
  • GB/T 2423.38 Environmental testing—Part 2:Test methods—Test R:Water test method and guidance*， 2021-05-21 Update
  • GB/T 2423.39 Environmental testing—Part 2：Test methods—Test Ee and guidance：Loose cargo testing including bounce*， 2018-12-28 Update
  • GB/T 2423.4 Environmental testing for electrical and electronic products - Part 2: Test method Test Db alternating damp heat (12h + 12h cycle)
  • GB/T 2423.40 Environmental testing.Part 2:Test methods.Test Cx:Damp heat, steady state(unsaturated pressurized vapour)*， 2013-12-31 Update
  • GB/T 2423.41 Environmental testing.Part 2:Test methods.Wind pressure*， 2013-11-12 Update
  • GB/T 2423.42 Basic environmental testing procedures for electric and electronic products. Combined low temperature/low air pressure/vibration(sinusoidal)test
  • GB/T 2423.43 Environmental testing for electric and electronic products.Part 2:Test method.Mounting of specimens for vibration,impact and similar dynamic tests
  • GB/T 2423.44 Environmental testing for electric and electronic products. Part 2: Test methods. Test Eg:Impact, spring hammer
  • GB/T 2423.45 Environmental testing.Part 2:Test methods.Test Z/ABDM:Climatic sequence*， 2012-12-31 Update
  • GB/T 2423.46 Environmental testing for electric and electronic products. Part 2: Tests methods. Test Ef: Impact, pendulum hammer
  • GB/T 2423.47 Environmental testing—Part 2: Test methods—Test Fg: Acoustic vibration*， 2018-12-28 Update
  • GB/T 2423.48 Environmental testing—Part 2:Test methods—Test Ff: Vibration—Time-history and sine-beat method*， 2018-12-28 Update
  • GB/T 2423.49 Environmental testing for electric and electronic products. Part 2: Test methods. Test Fe:Vibration--sine-beat method
  • GB/T 2423.5 Environmental testing—Part 2: Test methods—Test Ea and guidance: Shock*， 2019-05-10 Update
  • GB/T 2423.50 Environmental testing part 2: test method test Cy: constant damp heat is mainly used for accelerated testing of components*， 2012-11-05 Update
  • GB/T 2423.51 Environmental testing—Part 2: Test methods—Test Ke: Flowing mixed gas corrosion test*， 2020-06-02 Update
  • GB/T 2423.52 Environmental testing for electric and electronic products-Part 2:Test methods-Test 77:Body strength and impact shock
  • GB/T 2423.53 Environmental testing for electric and electronic products-Part 2:Test methods-Test Xb:Abrasion of markings and letterings caused by rubbing of fingers and hands
  • GB/T 2423.54 Environmental testing—Part 2: Test methods—Test Xc: Fluid contamination*， 2022-07-11 Update
  • GB/T 2423.55 Environmental testing for electric and electronic products.Part 2:Test methods.Test Eh:Hammer tests
  • GB/T 2423.56 Environmental Testing Part 2: Test Methods Test Fh: Broadband Random Vibration and Guidelines*， 2019-07-01 Update
  • GB/T 2423.57 Environmental testing for electric and electronic products.Part 2: Tests.Test Ei: Shock.Shock response spectrum synthesis
  • GB/T 2423.58 Enviromental testing for electric and electonic products.Part2:Tests methods.Test Fi:Vibration.Mixed Mode
  • GB/T 2423.59 Environmental testing for electric and electronic products.Part 2:Test methods.Test Z/ABMFh:Combined temperature(cold and heat)/low air pressure/vibration(random)
  • GB/T 2423.6 Environmental testing for electric and electronic products. Part 2: Test methods. Test Eb and guidance: Bump
  • GB/T 2423.60 Environmental testing for electric and electronic products.Part 2:Test methods.Test U:Robustness of terminations and integral mounting devices
  • GB/T 2423.61 Environmental testing—Part 2:Test methods—Test and guidance:Dust and sand test for large specimen*， 2018-12-28 Update
  • GB/T 2423.62 Environmental testing—Part 2:Test motheds—Test Fx and guidance:Mulit input mulit output vibration test*， 2018-12-28 Update
  • GB/T 2423.63 Environmental testing—Part 2:Test methods—Test: combined temperature(cold and heat)/low air pressure/vibration（mixed mode）*， 2019-05-10 Update
  • GB/T 2423.7 Environmental testing—Part 2：Test methods—Test Ec：Rough handling shocks，primarily for equipment—type specimens*， 2018-12-28 Update
  • GB/T 2423.8 Environmental testing for electric and electronic products. Parts 2: Test methods. Test Ed: Free fall
  • GB/T 2423.9 Environmental testing for electric and electronic products Part 2: Test methods Test Cb: Damp heat,steady state,primarily for equipment
  • GB/T 2900.20-1994 Electrotechnical terminology.High-voltage switchgear
  • GB/T 4796 Classification of environmental conditions—Environmental parameters and their severities*， 2017-12-29 Update
  • GB/T 4797.4 Classification of environmental conditions—Environmental conditions appearing in nature—Solar radiation and temperature*， 2019-12-10 Update
  • GB/T 4797.5 Classification of environmental conditions.Environmental conditions appearing in nature.Precipitation and wind*， 2017-12-29 Update
  • GB/T 5464 Non-combustibility test method for building materials*， 2010-09-26 Update

GB/T 17467-2010 history



Copyright ©2007-2023 ANTPEDIA, All Rights Reserved